Solid fuel fire PA9

Multiple Choice

Why is it important to ensure that solid fuel fires are installed properly in homes?

• To prevent house fires and ensure safety

• To make the fire look more attractive

• To reduce the cost of fuel

• To increase the temperature quickly

Multiple Choice

What are the main steps involved in the final stages of a building project as described in the session?

• Commissioning and handover

• Design and planning

• Site preparation and excavation

• Material procurement

Open Ended

What are the key documents and codes you need to access and read for your practical and theory assessments?

Fill in the Blanks

Multiple Select

Which of the following are component parts of the installation system mentioned in the session?

• Flue system

• Appliance

• Heat protectors

• Wood

Fill in the Blanks

Multiple Select

Which of the following codes must be used in addition to AS/NZ 2918:2018 for solid fuel heater installation?

• B1 (structure modifications)

• B2 (durability of modifications)

• E2 (flashing details and durability)

• C1 (fire safety)

Multiple Choice

Which regulation specifically covers the installation and compliance of solid fuel heaters in New Zealand?

• AS/NZ 2918: 2018

• B1

• B2

• E2

Open Ended

Explain the importance of maintaining minimum gaps between the flue pipe, inner casing, and outer casing in a tested flue system installation.

Multiple Choice

According to the general requirements for flue system installation, what is the maximum allowable flue length between 0° and 30° from the horizontal?

• 900 mm

• 1200 mm

• 1800 mm

• 600 mm

Open Ended

Describe how installing the eco flue system can improve the efficiency of a fire in a home environment.

Multiple Choice

According to AS/NZ2918 & Manufacturers Guides, what should be considered when installing appliances and heat protectors?

• Clearances and heat shielding

• Electrical wiring

• Plumbing connections

• Paint color

Open Ended

Explain the importance of proper flashing detail for pipe penetrations through roofing, as shown in the codes AS/NZ 2918 & E2.

Multiple Select

Which of the following are key steps in ensuring penetration and waterproofing are done correctly for a flue system?

• Using appropriate flashing materials

• Ensuring a tight seal around the pipe

• Leaving gaps for ventilation

• Securing the flashing with screws

Multiple Choice

What is the main difference between the flue systems shown for normal wind load and high wind load requirements?

• The height of the flue

• The use of support braces

• The color of the roof

• The type of roofing material

Fill in the Blanks

Multiple Choice

When a heat shield is more than 45° off the vertical, what is the clearance factor for a single layer of continuous material with a 12 mm air gap?

• 0.20

• 0.40

• 0.80

• 0.60

Multiple Select

Which materials shown in the first image are commonly used as heat shield materials?

• Brick

• Galvanized metal

• Wood

• Plastic

Multiple Choice

Which of the following is NOT a correct way to mount a wall protector for heat shielding?

• Mounted with all edges open

• Mounted on a single flat wall with top and bottom edges open

• Installed in a corner

• Mounted with all edges sealed against the wall

Open Ended

Explain why cross-ventilation air space is important in the construction of a floor protector for a heater.

Fill in the Blanks

Multiple Choice

What is the primary purpose of preparing the hearth surface before tiling, as shown in the third image?

• To improve aesthetics

• To ensure a level and stable base for the tiles

• To increase the height of the hearth

• To make cleaning easier

Multiple Choice

When setting out the fire as per manufacturer’s instructions on combustible surfaces, what is the most important consideration?

• Aesthetic alignment with the room

• Ensuring correct clearances from combustible materials

• Choosing the largest possible fire unit

• Using the thickest hearth material

Multiple Choice

What is one important reason to ensure your solid fuel fire is installed properly?

• To prevent house fires and ensure safety

• To make the fire look more attractive

• To reduce the amount of smoke produced

• To save money on installation costs