Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?

distribute list 2 out FastEthernet0/0

distribute list 1 out FastEthernet0/0

Router A and Router B are configured with IPv6 addressing and basic routing capabilities using OSPFv3. The networks that are advertised from Router A do not show up in Router B's routing table. After debugging IPv6 packets, the message "not a router" is found in the output. Why is the routing information not being learned by Router B?

IPv6 unicast routing is not enabled on Router A or Router B.

OSPFv3 timers were adjusted for fast convergence.

The networks were not advertised properly under the OSPFv3 process

An IPv6 traffic filter is blocking the networks from being learned via the Router B interface that is connected to Router A.

Refer to the following access list. access-list 100 permit ip any any log After applying the access list on a Cisco router, the network engineer notices that the router CPU utilization has risen to 99 percent. What is the reason for this?

A packet that matches access-list with the "log" keyword is process switched.

A packet that matches access-list with the "log" keyword is Cisco Express Forwarding switched.

A packet that matches access-list with the "log" keyword is fast switched.

A large amount of IP traffic is being permitted on the router.

What are the three modes of Unicast Reverse Path Forwarding?

strict mode, loose mode, and VRF mode

strict mode, loose mode, and broadcast mode

strict mode, broadcast mode, and VRF mode

broadcast mode, loose mode, and VRF mode

Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?

R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0

R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0

R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0

R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0

EIGRP is configured on all routes in the network. On a basis of the show ip eigrp topology output provided, what conclusion can be derived?

Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent about network 10.6.1.0/24

Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0

Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachable

Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24

EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors?

R4(config)# ip default-network 10.0.0.0

R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

R4(config)# ip route 10.0.0.0 255.0.0.0 10.1.1.1

R4(config-router)# default-information originate

What is a key benefit of using a GRE tunnel to provide connectivity between branch offices and headquarters?

dynamic routing over the tunnel

authentication, integrity checking, and confidentiality

For a GRE tunnel to be up between two routers, which of the following must be configured?

Tunnel interfaces must be in the same subnet.

IP reachability between the loopback interfaces

Dynamic Routing between routers

Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However, router RTB and RTC are not receiving each other's routes. What is the solution?

Issue the no ip split horizon eigrp 1 command on router RTA.

Configure the auto summary command under router eigrp 1 on router RTA

Issue the no ip split horizon command on router RTA.

Configure subinterfaces on the spoke routers and assign different IP address subnets for each subinterface.

Configure a distribute list on router RTA that allows it to advertise all routes to the spoke routers.

A Boston company bought the assets of a New York company and is trying to route traffic between the two data networks using EIGRP. The show command output shows that traffic will not flow between the networks. As a network consultant, you were asked to modify the configuration and certify the interoperability of the two networks. For traffic to flow from subnet 172.16.8.0/24 to the 172.16.16.0/24 subnet. Which configuration change do you recommend?

Turn off autosummarization on routers N1 and B1.

Add IP summary addresses to the Internet-pointing interfaces of routers N1 and B1.

Turn off auto summarization on routers N2 and B2.

Add wildcard masks to the network commands on routers N2 and B2.

A Boston company bought the assets of a New York company and is trying to route traffic between the two data networks using EIGRP over EoMPLS. As a network consultant, you were asked to verify the interoperability of the two networks. From the show ip route command output, what can you tell the customer about the traffic flow between the subnet in New York (172.16.8.0/24) and the subnets in Boston (172.16.16.0/24 and 10.10.16.0/24)?

Auto-summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0.

Traffic is flowing between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0 and no configuration changes are needed.

Traffic will flow between the 172.16.8.0 subnet and 172.16.16.0 without any further configuration changes. However, auto-summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and the 10.10.16.0 subnet.

Auto-summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and the 172.16.16.0 subnet. However, traffic will flow between the 172.16.8.0 subnet and 10.10.16.0 without any further configuration changes.

Refer to the exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?

Default metrics are not configured under EIGRP.

Redistribution must be enabled mutually (in both directions) to work correctly.

Auto-summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.34.0.0, which is already covered by the EIGRP protocol.

Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.

Which three statements are true? (Choose three.)

On the routing table of R4, the 10.1.1.0/24 route appears as an O E2 route

On R4, the 172.16.1.0/24 route has a metric of 20.

The administrative distance of the 172.16.1.0/24 route in the routing table of R3 is 170.

The R3 S0/0 interface should not need the no ip split-horizon eigrp 1 configuration command for the 172.16.1.0/24 route to appear in the routing table of R2 as an D EX route.

On R5, the 4.0.0.0/8 route will have an administrative distance of 120 and a hop count of 6.

You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes. What should you verify to troubleshoot this problem?

The administrative distance is set for OSPF and EIGRP.

The border router is using a proper seed metric for OSPF

The border router is using a proper seed metric for EIGRP.

The administrative distance is set for OSPF and EIGRP.

The subnet keyword on the border router in the redistribute OSPF command

In a redundant hub-and-spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response

Use the EIGRP Stub feature on routers C, D, E, and F.

Use address summarization at routers C, D, E, and F

Use passive-interface on the spoke links in routers A and B

Change the administrative distance in routers A and B for routes learned from routers C, D, E, and F

Which three statements are true about EIGRP operation? (Choose three.)

Automatic summarization across major network boundaries is enabled by default

When summarization is configured, the router will also create a route to null 0

Summarization is configured on a per-interface level

The summary route remains in the route table, even if there are no more specific routes to the network

The maximum metric for the specific routes is used as the metric for the summary route

Which two statements about the EIGRP DUAL process are correct? (Choose two.)

The stuck in active state is caused when the wait for the query replies have timed out.

An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table

An EIGRP route will go passive if there are no successors in the EIGRP topology table

DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.

A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to

Based on the exhibited output, which three statements are true? (Choose three.)

R1 is configured with the variance command

A default route has been redistributed into the EIGRP autonomous system

R1 is configured with the ip summary-address command

The route to 10.2.0.0/16 was redistributed into EIGRP

The router at 10.1.1.2 is configured with the ip default-network 0.0.0.0 command

When an EIGRP topology change is detected, what is the correct order of events when there is a FS?

DUAL is notified. The neighbor adjacency is deleted. Remove all topology entries learned from that neighbor. The feasible route is used.

The neighbor adjacency is deleted. The feasible route is used. DUAL is notified. Remove all topology entries learned from that neighbor

DUAL is notified. Remove all topology entries learned from that neighbor. The neighbor adjacency is deleted. Routes enter the Active state and the feasible route is used

The neighbor adjacency is deleted. Routes enter the Active state and the feasible route is used. DUAL is notified. Remove all topology entries learned from that neighbor

Which two statements are true about EIGRP manual summarization? (Choose two.)

Manual summarization is configured on a per interface basis.

The summary address is entered into the routing table and is shown to be sourced from the Null0 interface

Manual summaries can be configured with the classful mask only.

When manual summarization is configured, autosummarization is automatically disabled by default.

The summary address is assigned an administrative distance of 10 by default.

Given the above output, which statement is true?

192.168.1.0 is a redistributed route into EIGRP

192.168.1.0 is a summarized route

192.168.1.0 is equal path load balancing with 172.16.1.0

What happens when the router stops receiving advertisements for the 10.1.2.0/24 network?

The summary route will remain in the table

The summary route will be removed from the table

The more specific routes will be advertised from the table.

10.1.2.0/24 will still be advertised but packets destined for it will be dropped when they reach this router

On all routers in the network, EIGRP has been configured for load balancing across the three links. However, traffic destined for Network B from R1 is only load balanced over paths R1- R2-R5 and R1-R3-R5. What is the cause of the problem?

Because Router R4 is not a feasible successor, EIGRP will not select path R1-R4-R5 for load balancing

EIGRP will not select more than two links for unequal cost path load balancing

Because the path has a different link type, EIGRP will not select path R1-R4-R5 for load balancing

EIGRP will not select path R1-R4-R5 for load balancing unless the value of the variance parameter is increased

Identify three characteristics of EIGRP feasible successors? (Choose three.)

A feasible successor is selected by comparing the advertised distance of a non-successor route to the feasible distance of the best route.

If the advertised distance of the non-successor route is less than the feasible distance of best route, then that route is identified as a feasible successor

If the successor becomes unavailable, then the feasible successor can be used immediately without recalculating for a lost route.

The feasible successor can be found in the routing table.

Traffic will be load balanced between feasible successors with the same advertised distance

Which are three features of EIGRP? (Choose three)

Support VLSM and discontiguous subnets

External Administrative distance is 100

Which two options are requirements for EIGRP authentication? (Choose two)

. The Authentication key must be configured under the interface running EIGRP

. The authentication key IDs must match between two neighbors

A crypto map must be configured

The authentication key must be configured within the EIGRP routing configuration

A separate key chain must be configured.

Which two actions can you take to prevent routes from becoming stuck in active? (Choose two.)

Design the network so that it uses the lowest possible number of queries

Increase the time a router waits before it declares routes stuck in active

Manually increase the EIGRP metrics on interfaces connected to successors

Use port channeling to aggregate multiple EIGRP interfaces.

Increase the EIGRP K values on low-bandwidth interfaces

Which two statements about the passive-interface command issued under EIGRP are true? (Choose Two.)

If it is enabled globally under EIGRP on the device, it can be disable for individual interfaces to allow those interfaces to remain

It disables processing of incoming hello messages

It configures the interface to use unicast messages to establish EIGRP neighbor relationships

It configures the device to advertise only connected interfaces to neighbors with EIGRP

It allows incoming routing updates to be received but disables outgoing updates

Which condition must be satisfied before an EIGRP neighbor can be considered a feasible successor?

The neighbor's advertised distance must be less than the feasible distance of the current successor

The neighbor's advertised distance must be less than or equal to the feasible distance of the current successor

The neighbor's advertised distance must be greater than the feasible distance of the current successor

The neighbor's advertised distance must be equal to the feasible distance of the current successor.

For a GRE tunnel to be up between two routers, which of the following must be configured?

Tunnel interfaces must be in the same subnet

IP reachability between the loopback interfaces

Dynamic Routing between routers

When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful. What is the next thing that should be checked?

Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router

Verify that the EIGRP hello and hold timers match exactly

Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command

Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command

Which statement about dynamic routing protocols for this network is true?

With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization points.

No dynamic interior routing protocol can summarize as shown

Unless configured otherwise, EIGRP would automatically summarize the prefixes as shown in the exhibit.

The IP address design lends itself to OSPF. Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy

CCNP Route

Authored by gopi venketesan

Computers

University

Used 22+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

50 questions

Show all answers

MULTIPLE CHOICE QUESTION

1 min • 1 pt

Which method allows IPv4 and IPv6 to work together without requiring both to be used for a single connection during the migration process?

dual-stack method

6to4 tunneling

GRE tunneling

NAT-PT

MULTIPLE SELECT QUESTION

2 mins • 1 pt

A network administrator executes the command clear ip route. Which two tables does this command clear and rebuild? (Choose two.)

IP routing

FIB

ARP cache

MAC address table

Cisco Express Forwarding table

MULTIPLE SELECT QUESTION

30 sec • 1 pt

Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three.)

header compression

explicit congestion notification

keepalive

time stamps

TCP path discovery

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the opposite
direction. Which UDP characteristic does this scenario describe?

latency

starvation

connectionless communication

nonsequencing unordered packets

jitter

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

PPPoE is composed of which two phases?

Active Authentication Phase and PPP Session Phase

Passive Discovery Phase and PPP Session Phase

Active Authorization Phase and PPP Session Phase

Active Discovery Phase and PPP Session Phase

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which one statement is true?

Traffic from the 172.16.0.0/16 network will be blocked by the ACL.

The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the 10.0.0.0/8 network is missing from Router B.

The 10.0.0.0/8 network will not be in the routing table on Router B.

Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but users on the 192.168.5.0/24 cannot successfully ping users on

the 10.0.0.0/8 network.

Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. Which message is required to obtain a global
unicast address when a router is present?

DHCPv6 request

router-advertisement

neighbor-solicitation

redirect

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

47 questions

Relational Database Design

Quiz

•

University

50 questions

USBN TIK KELAS 9A-9C

Quiz

•

9th Grade - University

50 questions

Examen final hardware y software

Quiz

•

University

50 questions

AP CS P 5.1

Quiz

•

10th Grade - University

45 questions

Kuis Sistem Komputer

Quiz

•

10th Grade - University

45 questions

IP MIDTERM

Quiz

•

University

50 questions

PNETSEC Final Examination (II-BINS)

Quiz

•

University

50 questions

MidExam InfoAssuSec2

Quiz

•

University

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

54 questions

Analyzing Line Graphs & Tables

Quiz

•

4th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

15 questions

Equivalent Fractions

Quiz

•

4th Grade

Discover more resources for Computers

20 questions

CompTIA Network+ - Ports and Protocols

Quiz

•

University

CCNP Route

Which method allows IPv4 and IPv6 to work together without requiring both to be used for a single connection during the migration process?

A network administrator executes the command clear ip route. Which two tables does this command clear and rebuild? (Choose two.)

Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three.)

A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the opposite
direction. Which UDP characteristic does this scenario describe?

PPPoE is composed of which two phases?

Which one statement is true?

A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. Which message is required to obtain a global
unicast address when a router is present?

An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters:

mac address C601.420F.0007
subnet 2001:DB8:0:1::/64

Which IPv6 addresses should the engineer add to the documentation?

Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?

Which prefix is matched by the command ip prefix-list name permit 10.8.0.0/16 ge 24 le 24?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers

CCNP Route

Which method allows IPv4 and IPv6 to work together without requiring both to be used for a single connection during the migration process?

A network administrator executes the command clear ip route. Which two tables does this command clear and rebuild? (Choose two.)

Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three.)

A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the oppositedirection. Which UDP characteristic does this scenario describe?

PPPoE is composed of which two phases?

Which one statement is true?

A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. Which message is required to obtain a globalunicast address when a router is present?

An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters:mac address C601.420F.0007subnet 2001:DB8:0:1::/64Which IPv6 addresses should the engineer add to the documentation?

Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?

Which prefix is matched by the command ip prefix-list name permit 10.8.0.0/16 ge 24 le 24?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers

A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the opposite
direction. Which UDP characteristic does this scenario describe?

A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. Which message is required to obtain a global
unicast address when a router is present?

An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters:

mac address C601.420F.0007
subnet 2001:DB8:0:1::/64

Which IPv6 addresses should the engineer add to the documentation?