Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?

Default metrics are not configured under EIGRP

The subnet defined in OSPF is not part of area 0

There is no overlap in the subnets advertised

The routing protocols do not have the same AS number

Which statement about this neighbor of R1 is true?

R1 used ICMP to learn about this neighbor.

OSPFv3 adjacency has been lost, which causes the neighbor to be considered Stale.

Aggregate global addresses are always used between IPv6 neighbors.

OSPFv3 adjacency will not work between link-local addresses

What two statements are true? (Choose two)

Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command

The IP address of the backup designated router (BDR) is FE80:205:5FFF:FED3:5808

OSPF version 2 has been enabled to support IPv6

The output was generated by the show ip interface command

The router was configured with the commands: router ospf 1 network 172.16.6.0 0.0.0.255 area 1

What does the command clear ipv6 ospf process accomplish?

The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.

The OSPF adjacencies are cleared and initiated again

The route table is cleared. Then the OSPF neighbors are reformed

The shortest path first (SPF) algorithm is performed on the LSA database

In IPv6, the interfaces running OSPF can be configured with multiple address prefixes. Which statement is true about the IPv6 addresses that can be included into the OSPF process?

Specific addresses cannot be selected for importation into the OSPF process

Specific addresses can be selected using an ACL.

Specific addresses can be selected using a route map

Specific addresses can be selected using a prefix list

Which statement is true about the command ipv6 ospf 1 area 0?

It must be issued in interface configuration mode to enable the OSPF process for IPv6

It must be issued in router global configuration mode to enable the OSPF process for IPv6

It must be issued before the network command to enable the OSPF process for IPv6

It must be issued after the network command to enable the OSPF process for IPv6

Which statement is true?

RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will translate the type 7 LSAs into type LSAs and flood them throughout the OSPF backbone

RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will flood the type 7 LSAs throughout the backbone.

RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will flood the type 5 LSAs throughout the backbone

RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will translate the type of 5 LSAs unto type 7 LSAs and flood them throughout the OSPF backbone

RTA will not redistribute the RIP routers into the NSSA.

Will redistributed RIP routes from OSPF Area 2 be allowed in Area 1?

Because Area 1 is an NSSA, redistributed RIP routes will not be allowed

Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 5 LSAs in Area 0 and passed on into Area 1.

Because NSSA will discard type 7 LSAs, redistributed RIP routes will not be allowed in Area 1.

Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 7 LSAs in Area 0 and passed on into Area 1

RIP routes will be allowed in Area 1 only if they are first redistributed into EIGRP

Which three route filtering statements are true? (Choose three)

After the router rip and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface

When you use the passive-interface command with EIGRP, hello messages are not sent out the specified interface

When you use the passive-interface command with OSPF, hello messages are not sent out the specified interface

After the router eigrp 10 and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface

After the router ospf 10 and passive-interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface

Which two statements are correct regarding the routes to be redistributed into OSPF? (Choose two)

The network 192.168.1.0 will be allowed and assigned a metric of 100

The network 172.16.0.0/16 will be allowed and assigned a metric of 200

The network 192.168.1.0 will be allowed and assigned a metric of 200

All networks except 10.0.0.0/8 will be allowed and assigned a metric of 200

The network 10.0.10.0/24 will be allowed and assigned a metric of 200

Which three statements are true when configuring redistribution for OSPF? (Choose two)

Subnets do not redistribute by default

Subnets redistribute by default

A network administrator is troubleshooting a redistribution of OSPF routes into EIGRP. router eigrp 1 network 10.0.0.0 ! router ospf 1 network 172.10.0.0 0.0.255.255 area O redistribute eigrp 1 Given the exhibited commands, which statement is true?

Redistributed routes will have an external type of 2 and a metric of 20.

Redistributed routes will have an external type of 1 and a metric of 1.

Redistributed routes will maintain their original OSPF routing metric

Redistributed routes will have a default metric of 0 and will be treated as reachable and advertised.

Redistributed routes will have a default metric of 0 but will be treated as unreachable and not advertised.

A router is configured for redistribution to advertise EIGRP routes into OSPF on a boundary router. Given the configuration: router ospf 1 redistribute eigrp 1 metric 25 subnets What is the function of the 25 parameter in the redistribute command?

It specifies the seed cost to be applied to the redistributed routes

It specifies the administrative distance on the redistributed routes

It specifies the metric limit of 25 subnets in each OSPF route advertisement

It specifies a new process-id to inject the EIGRP routes into OSPF.

R1 and R2 belong to the RIP routing domain that includes the networks 10.20.0.0/16 and 10.21.0.0/16. R3 and R4 are performing two-way route redistribution between OSPF and RIP. A network administrator has discovered that R2 is receiving OSPF routes for the networks 10.20.0.0/16 and 10.21.0.0/16 and a routing loop has occurred. Which action will correct this problem?

Configure distribute-lists on R3 and R4

Apply an inbound ACL to the R2 serial interface

Change the RIP administrative distance on R3 to 110

Set the OSPF default metric to 20

Change the OSPF administrative distance on R3 to 110

Which command should be added to RTB under router bgp 100 to allow only the external OSPF routes to be redistributed to RTC?

redistribute ospf 1 match external 1 external 2

redistribute ospf 1 match external 1

redistribute ospf 1 match external 2

Routers R2, R3, R4, and R5 have OSPF enabled. What should be configured on the routers in area 1 to ensure that all default summary routes and redistributed EIGRP routes will be forwarded from R6 to area 1, and only a default route for all other OSPF routes will be forwarded from R5 to area 1.

R5(config-router)# area 1 nssa no-summary R6(config-router)# area 1 nssa

R5(config-router)# area 1 stub R6(config-router)# area 1 stub

R5(config-router)# area 1 stub no-summary R6(config-router)# area 1 stub

R5(config-router)# area 1 nssa R6(config-router)# area 1 nssa

A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. What did the TAC engineer configure incorrectly?

The interface tunnel configuration is not correct

The crypto isakmp configuration is not correct

The crypto map configuration is not correct

The network 172.16.1.0 is not included in the OSPF process

In the network diagram, Area 1 is defined as a stub area. Because redistribution is not allowed in the stub area, EIGRP routes cannot be propagated into the OSPF domain. How does defining area 1 as a not-so-stubby area (NSSA) make it possible to inject EIGRP routes into the OSPF NSSA domain?

by creating a link between the EIGRP domain and the RIP domain, and redistributing EIGRP into RIP

by manually changing the routing metric of EIGRP so that it matches the routing metric of OSPF

A network engineer configures two connected routers to run OSPF in Area 0; however, the routers fail to establish adjacency. Which option is one of the caused for this issue?

The Same OSPF router IDs are configured on both routers

OSPF process numbers do not match on both neighbor routers

The Same MTU sizes are configured on both sides

Which two OSPF router types can perform summarize in an OSPF network? (Choose Two)

autonomous system boundary router

Which two statements about OSPF E1 routes are true? (Choose Two)

They use the OSPF cost from redistribution and the OSPF cost to the ASBR

They are preferred over E2 routes

They are preferred over interarea routes

They use only the OSPF cost to the ASBR

They use only the OSPF cost from redistribution

If this configuration is applied to a device that redistributes EIGRP routes into OSPF. which two statements about the behavior of the device are true? (Choose Two )

The device redistributes all EIGRP networks into OSPF

The device redistributes only classful EIGRP networks into OSPF

EIGRP routes appears in the routing table as E2 OSPF routes

The device router ID is set to Loopback0 automatically

EIGRP routes appears in the routing table as N2 OSPF routes

A network engineer has configured NTP on a Cisco router, but the time on the router is still incorrect. What is the reason for this problem?

The router is not syncing with the peer, even though the NTP request and response packets are being exchanged.

The router is not syncing with peer, and the NTP request and response packets are not being exchanged.

The router is syncing with the peer, and the NTP request and response packets are being exchanged.

The router is dropping all NTP packets

If you convert a WAN connection with OSPF from T1 to a Frame Relay circuit, which two actions must you take to enable the connection? (Choose Two)

Change the OSPF network type to nonbroadcast

Manually configure neighbors in the OSPF process

Manually configure the hello and dead timers

Change the OSPF network type to broadcast

Change the OSPF network type to multipoint nonbroadcast

OSPF has R1 router ID 172.18.1.1 . What happens when R1 configure with a new loopback interface IP address 172.17.1.1 ?

OSPF chooses 172.17.1.1 as new router ID when R1 is rebooted

OSPF chooses 192.168.21.0 as new router ID when apply new configuration

OSPF chooses 172.17.1.1 as new router ID when apply new configuration.

OSPF retains 172.18.1.1 as router ID until interface on which is configured goes down

What are two impotant differences between OSPFv2 and OSPFv3 (Choouse two.)

Only OSPFv3 provides support for IPv6

Only OSPFv3 supports multiple OSPF instances on a single link.

Only OSPFv3 automatically chooses a router ID for the local device

Only OSPFv3 automatically enable interfaces when you create them in device configuration mode

Only OSPFv3 automatically detects OSPF neighbors on an NBMA interface.

Which two statements about OSPFv3 are true?(Choose two)

The router ID is configured as an IPv4 address

It uses link-local addresses to from neighbor relationships

The router ID is configured as an IPv6 address

It uses loopback IPv6 addresses to from neighbor relationships

It uses LSA type 6 for intra-area prefixes

You want to configure a device to select an OSPF-learned route as the preferred path over an EBGPlearned route Which action must you take?

Decrease the OSPF administative distance

Increase the OSPF administrative distance

OSPF chooses routes in which order, regardless of route's administrative distance and metric?

Intra-Area (O) - Inter-Area (O IA) - External Type 1 (E1) - External Type 2 (E2) - NSSA Type 1 (N1) - NSSA Type 2 (N2)

Intra-Area (O) - Inter-Area (O IA) - NSSA Type 1 (N1) - NSSA Type 2 (N2) - External Type 1 (E1) - External Type 2 (E2)

Intra-Area (O) - Inter-Area (O IA) - NSSA Type 1 (N1) - External Type 1 (E1) - NSSA Type 2 (N2) - External Type 2 (E2)

Intra-Area (O) - NSSA Type 1 (N1) - External Type 1 (E1) - Inter-Area (O IA) - NSSA Type 2 (N2) - External Type 2 (E2)

Intra-Area (O) - Inter-Area (O IA) - NSSA Type 1 (N1) - External Type 1 (E1) - NSSA Type 2 (N2) - External Type 2 (E2)

Which two statements are true of the OSPF link-state routing protocol? (Choose two.)

OSPF sends summaries of individual link-state entries every 30 minutes to ensure LSDB synchronization

OSPF sends triggered updates when a network change occurs

Using the Bellman-Ford algorithm, each OSPF router independently calculates its best paths to all destinations in the network

Using the DUAL algorithm, each OSPF router independently calculates its best paths to all destinations in the network

OSPF sends updates every 10 seconds

You get a call from a network administrator who tells you that he typed the following into his router: Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0 He tells you he still can’t see any routes in the routing table. What configuration error did the administrator make?

The OSPF process ID is incorrect

Two aspects of an IP SLA operation can be tracked: state and reachability. Which statement about state tracking is true?

When tracking state, an OK return code means that the track's state is up; any other return code means that the track's state is down.

When tracking state, an OK or over threshold return code means that the track's state is up; any other return code means that the track's state is down.

When tracking state, an OK return code means that the track's state is down; any other return code means that the track's state is up

When tracking state, an OK or over threshold return code means that the track's state is down; any other return code means that the track's state is up

Which two reasons for IP SLA tracking failure are likely true? (Choose Two)

The source-interface is configured incorrectly

A route back to the RI LAN network is missing in R2

The destination must be 172.30.30.2 for icmp-echo

The default route has wrong next hop IP address

Given with configuration written on Picture as R1(Config)# ip sla 1 R1(Config-ip-sla)# icmp-echo 172.20.20.2 source-interface f1/0 R1(Config-ip-sla)# frequency 10 R1(Config-ip-sla)# threshold 100 R1(Config)# ip sla schedule 1 start-time now life forever R1(Config)# track 10 ip sla ??? R1(Config)# ip route 0.0.0.0 0.0.0.0 172.20.20.2 What make default route not removed when SLA state down or failed ?

missing of track feature on default static route command

the destination must be 172.30.30.2 for icmp-echo

UDP Jitter for VolP has not been configured

OSPF

Authored by gopi venketesan

Computers

Professional Development

Used 21+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

50 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?

Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 47.

Either a firewall between the two routers or an ACL on the router is blocking UDP 57

Either a firewall between the two routers or an ACL on the router is blocking TCP 47

Either a firewall between the two routers or an ACL on the router is blocking IP protocol number 57.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

The OSPF database of a router shows LSA types 1, 2, 3, and 7 only. Which type of area is this router connected to?

stub area

totally stubby area

backbone area

not-so-stubby area

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Refer to the exhibit showing complete command output. What type of OSPF router is Router A?

internal router

ASBR

ABR

edge router

MULTIPLE SELECT QUESTION

30 sec • 1 pt

Which two OSPF network types can operate without a DR/BDR relationship? (Choose Two)

Point-to-multipoint

Point-to-point

nonbroadcast

nonbroadcast multi-access

broadcast

MULTIPLE SELECT QUESTION

30 sec • 1 pt

A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two)

Change the network type to point-to-multipoint under WAN interface

Enable virtual links

Change the network type to nonbroadcast multipoint access

Configure the neighbor command under OSPF process for each remote site

Ensure that the OSPF process number matches among all remote sites

MULTIPLE SELECT QUESTION

30 sec • 1 pt

Refer to following:
router eigrp 1
redistribute ospf 1 route-map ospf-to-eigrp
default-metric 20000 2000 255 1 1500
!
route-map ospf-to-eigrp deny 10
match tag 6
match route-type external type-2
!
route-map ospf-to-eigrp permit 20
match ip address prefix-list pfx
set metric 40000 1000 255 1 1500
!
route-map ospf-to-eigrp permit 30
set tag 8

Which three statements accurately describe the result of applying the exhibited route map?

The map prohibits the redistribution of all type 2 external OSPF routes with tag 6 set.

The map prohibits the redistribution of all type 2 external OSPF routes.

The map redistributes into EIGRP all routes that match the pfx prefix list and the five metric values 40000, 1000, 255, 1, and 1500

All routes that do no match clauses 10 and 20 of the route map are redistributed with their tags set to 8.

The map permits the redistribution of all type 1 external OSPF routes.

MULTIPLE SELECT QUESTION

30 sec • 1 pt

Using new backup router in spite of faulty one in ospf domain but relationship with neighbor in one interface only not working, what is the reason of this problem? (Choose Two)

area Id mismatch

authentication mismatch

process id of ospf not match

ospf timers not match

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

50 questions

Quizz Compition(Social Media,cyber Crime,Ms Word,Cyber Security)

Quiz

•

Professional Development

50 questions

RUTS Technology

Quiz

•

9th Grade - Professio...

46 questions

A+ 1101 Study Quiz 1

Quiz

•

Professional Development

50 questions

DGI- QUIZ

Quiz

•

Professional Development

50 questions

M1 R5 ( Chapter 4)

Quiz

•

Professional Development

54 questions

Cambridge L3 IT Hardware Diagnostic Quiz

Quiz

•

Professional Development

50 questions

Microsoft Azure Fundamentals AZ-900 ENG #6

Quiz

•

University - Professi...

50 questions

Orientation Quiz

Quiz

•

University - Professi...

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

54 questions

Analyzing Line Graphs & Tables

Quiz

•

4th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

15 questions

Equivalent Fractions

Quiz

•

4th Grade

Discover more resources for Computers

20 questions

Black History Month Trivia Game #1

Quiz

•

Professional Development

100 questions

Screening Test Customer Service

Quiz

•

Professional Development

20 questions

90s Cartoons

Quiz

•

Professional Development

10 questions

Reading a ruler in Inches

Quiz

•

4th Grade - Professio...

16 questions

Parallel, Perpendicular, and Intersecting Lines

Quiz

•

KG - Professional Dev...

12 questions

Valentines Day Trivia

Quiz

•

Professional Development

OSPF

After configuring GRE between two routers running OSPF that are connected to each other via a WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin the exchange of routing updates. What is the reason for this?

The OSPF database of a router shows LSA types 1, 2, 3, and 7 only. Which type of area is this router connected to?

Refer to the exhibit showing complete command output. What type of OSPF router is Router A?

Which two OSPF network types can operate without a DR/BDR relationship? (Choose Two)

A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two)

Using new backup router in spite of faulty one in ospf domain but relationship with neighbor in one interface only not working, what is the reason of this problem? (Choose Two)

Which LSA type can exist only in an OSPF NSSA area?

Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers