High Availability

You have a Windows Server 2016 Hyper-V failover cluster that contains two nodes named Node1 and Node2.

On Node1, you create a virtual machine named VM01 by using Hyper-V Manager.

You need to configure VM01 to move to Node2 automatically if Node1 becomes unavailable. What should you do?

• From Failover Cluster manager, run the configure Role actions.

• From Hyper-V Manager, click VM01 and click Enable Replication.

• From Hyper-V Manager Click Node 1 and the modify the hyper-V settings.

• From Windows Powershell, run the Enable-VMReplication cmdlet.

You have two servers named Server1 and Server2 that run Windows Server 2016. Server1 and Server2 have the Hyper-V server role installed.

An iSCSI SAN connects to the network.

You create a LUN on the SAN and configure both servers to connect to the iSCSI target. You create a failover cluster and add Server1 and Server2 to the cluster.

You connect both servers to the iSCSI target and format the shared storage.

You need to add the shared storage to the cluster. The solution must ensure that virtual machines running on both nodes can access the shared storage simultaneously.

Which tool should you use?

• the clussvc.exe command

• the cluster.exe command

• the Computer Management console

• the Failover Cluster Manager console

• the Disk Management console

One of your team previously opened Hyper-V Manager, selected a virtual machine and followed the Enable Replication wizard.

The process was completed successfully and replications were occurring as expected.

Several weeks later and you now want to run a planned failover. Which of the following steps is the correct starting point?

• Right-click the primary vM and select Replication > Planned Failover

• Right-click the replica vM and select Replication > Planned Failover

• Right-click the primary VM and select Replication > Extend Replication

• Right-click the replica VM and select Replication > Test Failover

You have two servers named Server1 and Server2 that run Windows Server 2016. Server1 and Server2 have the Hyper-V server role installed and are nodes in a failover cluster.

On Server1, an administrator creates a virtual machine named VM1. You need to configure VM1 for high availability.

Which tool should you use?

• the Failover Cluster Manager snap-in

• the clussvc.exe command

• the cluster.exe command

• the Computer Management snap-in

• the configurehyperv.exe command

You deploy two servers that run Windows Server 2016. You install the Failovers Clustering feature on both servers. You need to create a workgroup cluster.

What should you do?

• Create matching local administrative accounts on both of the servers. Assign the same primary DNS suffix to both of the servers. Run the New-Cluster cmdlet and specify an administrative access point of None.

• Configure both of the servers to be in a workgroup named Workgroup. Configure the Cluster Service to log on as Network Service. Run the New-Cluster cmdlet and specify an administrative access point of DNS.

• Create matching local administrative accounts on both of the servers. Assign the same primary DNS suffix to both of the servers. Run the New-Cluster cmdlet and specify an administrative access point of DNS

• Configure both of the server to be in a workgroup named Workgroup. Configure the Cluster Service to log on as Network Service. Run the New-Cluster cmdlet and specify an administrative access point of None.

You have four Hyper-V hosts named Server1, Server2, Server3 and Server4 that run Windows Server 2016. The hosts are nodes in a failover cluster.

The failover cluster is configured to balance virtual machines when a node is more than 80 percent loaded.

You need to configure the failover cluster to balance the virtual machines when the load of a node is more than five percent higher than the average for the nodes.

Which command should you run?

• Get-Cluster AutoBalanceLevel=3

• Get-ClusterNode AutoBalanceMode=3

• Get-ClusterParameter DynamicQuorum=1

• Get-ClusterResource DynamicQuorum=5

You have a Windows Server 2016 failover cluster named Cluster1 that contains three nodes named Server1, Server2, and Server3. Each node hosts several virtual machines. The virtual machines are configured to fail over to another node in Cluster1 if the hosting node fails.

You need to ensure that if the Cluster service fails on one of the nodes, the virtual machine of that node will fail over immediately.

Which setting should you configure?

• FailureConditionLevel

• QuarantineDuration

• ResiliencyPeriod

• ResiliencyLevel

You have a Windows Server 2106 failover cluster named Cluster1 that contains four nodes named Server1, Server2, Server3, and Server4. Cluster1 hosts 40 virtual machines that are distributed evenly across the nodes.

Server1 and Server2 are located in a data center in Madrid. Server3 and Server4 are located in a data center in Barcelona.

You need to ensure that when you pause a node, the clustered virtual machines will always attempt to move automatically to another node in the same data center before attempting to move to a node in the other data center.

Which two actions should you perform? Each correct answer presents part of the solution.

• Run the New-ClusterFaultDomain cmdlet.

• Run the Add-ClusterGroup cmdlet.

• Configure a file share witness for each data center.

• Run the Set-ClusterFaultDomain cmdlet.

• Change the quorum configuration of the cluster to Node Majority.

You have a Scale-Out File Server that has a share named Share 1. Share1 contains a virtual disk named Disk1.vhd.

You plan to create a guest failover cluster.

You need to ensure that you can use the virtual disk as a shared virtual disk for the guest failover Cluster.

Which cmdlet should you use?

• Oplimize-VHD

• Convert-VHD

• Set-VHO

• Optimtze-VHDSet

You have two servers that run Windows Server 2016.

You plan to create a Network load Balancing (NLB) cluster that will contain both servers. You need to configure the network cards on the servers for the planned NLB configuration. Solution: You configure the network cards to be on the same subnet and to have dynamic IP addresses.

You configure the cluster to use multicast. Does this meet the goal?

• Yes

• No