109. In which situation would a technician use the show interfaces switch command?

when packets are being dropped from a particular directly attached host

to determine if remote access is enabled

when an end device can reach local devices, but not remote devices

to determine the MAC address of a directly attached network device on a particular interface

110. What is a drawback of the local database method of securing device access that can be solved by using AAA with centralized servers?

User accounts must be configured locally on each device, which is an unscalable authentication solution.

There is no ability to provide accountability.

It is very susceptible to brute-force attacks because there is no username.

The passwords can only be stored in plain text in the running configuration.

111. What action does a DHCPv4 client take if it receives more than one DHCPOFFER from multiple DHCP servers?

It sends a DHCP REQUEST that identifies which lease offer the client is accepting.

It sends a DHCPNAK and begins the DHCP process over again.

It discards both offers and sends a new DHCPDISCOVER.

It accepts both DHCPOFFER messages and sends a DHCPACK.

112. Refer to the exhibit. The network administrator is configuring the port security feature on switch SWC. The administrator issued the command show port-security interface fa 0/2 to verify the configuration. What can be concluded from the output that is shown? (Choose three.)

Security violations will cause this port to shut down immediately.

The switch port mode for this interface is access mode.

Three security violations have been detected on this interface.

There is no device currently connected to this port.

114. A network administrator has found a user sending a double-tagged 802.1Q frame to a switch. What is the best solution to prevent this type of attack?

The VLANs for user access ports should be different VLANs than any native VLANs used on trunk ports.

The native VLAN number used on any trunk should be one of the active data VLANs.

Trunk ports should be configured with port security.

Trunk ports should use the default VLAN as the native VLAN number.

115. Refer to the exhibit. Which two conclusions can be drawn from the output? (Choose two.)

The port channel is a Layer 3 channel.

The bundle is fully operational.

The load-balancing method used is source port to destination port.

118. Refer to the exhibit. A network engineer is configuring IPv6 routing on the network. Which command issued on router HQ will configure a default route to the Internet to forward packets to an IPv6 destination network that is not listed in the routing table?

ip route 0.0.0.0 0.0.0.0 serial 0/1/1

119. Users are complaining of sporadic access to the internet every afternoon. What should be done or checked?

Check the statistics on the default route for oversaturation.

Create static routes to all internal networks and a default route to the internet.

Verify that there is not a default route in any of the edge router routing tables.

Create a floating static route to that network.

120. What action takes place when the source MAC address of a frame entering a switch appears in the MAC address table associated with a different port?

The switch replaces the old entry and uses the more current port.

The switch purges the entire MAC address table

The switch updates the refresh timer for the entry.

The switch forwards the frame out of the specified port

121. A network administrator is configuring a WLAN. Why would the administrator use a WLAN controller?

to facilitate group configuration and management of multiple WLANs through a WLC

to provide privacy and integrity to wireless traffic by using encryption

to centralize management of multiple WLANs

to provide prioritized service for time-sensitive applications

123. Which three statements accurately describe duplex and speed settings on Cisco 2960 switches? (Choose three.)

An auto negotiation failure can result in connectivity issues.

When the speed is set to 1000 Mb/s, the switch ports will operate in full-duplex mode.

The duplex and speed settings of each switch port can be manually configured.

Enabling autonegotiation on a hub will prevent mismatched port speeds when connecting the hub to the switch.

124. Refer to the exhibit. A network administrator configures R1 for inter-VLAN routing between VLAN 10 and VLAN 20. However, the devices in VLAN 10 and VLAN 20 cannot communicate. Based on the configuration in the exhibit, what is a possible cause for the problem?

D. The command interface gigabitEthernet 0/0.1 is wrong.

A. The port Gi0/0 should be configured as trunk port.

B. The encapsulation is misconfigured on a subinterface.

C. A no shutdown command should be added in each subinterface configuration.

125. A network administrator uses the spanning-tree portfast bpduguard default global configuration command to enable BPDU guard on a switch. However, BPDU guard is not activated on all access ports. What is the cause of the issue?

PortFast is not configured on all access ports.

BPDU guard needs to be activated in the interface configuration command mode.

Access ports configured with root guard cannot be configured with BPDU guard.

Access ports belong to different VLANs.

128. A WLAN engineer deploys a WLC and five wireless APs using the CAPWAP protocol with the DTLS feature to secure the control plane of the network devices. While testing the wireless network, the WLAN engineer notices that data traffic is being exchanged between the WLC and the APs in plain-text and is not being encrypted. What is the most likely reason for this?

Although DTLS is enabled by default to secure the CAPWAP control channel, it is disabled by default for the data channel.

DTLS only provides data security through authentication and does not provide encryption for data moving between a wireless LAN controller (WLC) and an access point (AP).

DTLS is a protocol that only provides security between the access point (AP) and the wireless client.

Data encryption requires a DTLS license to be installed on each access point (AP) prior to being enabled on the wireless LAN controller (WLC).

129. A new switch is to be added to an existing network in a remote office. The network administrator does not want the technicians in the remote office to be able to add new VLANs to the switch, but the switch should receive VLAN updates from the VTP domain. Which two steps must be performed to configure VTP on the new switch to meet these conditions? (Choose two.)

Configure the new switch as a VTP client.

Configure the existing VTP domain name on the new switch.

Configure all ports of both switches to access mode.

Configure an IP address on the new switch.

130. Refer to the exhibit. Consider that the main power has just been restored. PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?

to Fa0/1, Fa0/2, and Fa0/3 only

o Fa0/1, Fa0/2, Fa0/3, and Fa0/4

to Fa0/1, Fa0/2, and Fa0/4 only

131. What action takes place when the source MAC address of a frame entering a switch is not in the MAC address table?

The switch adds the MAC address and incoming port number to the table.

The switch adds a MAC address table entry for the destination MAC address and the egress port.

The switch replaces the old entry and uses the more current port.

The switch updates the refresh timer for the entry.

132. Employees are unable to connect to servers on one of the internal networks. What should be done or checked?

Use the “show ip interface brief” command to see if an interface is down.

Verify that there is not a default route in any of the edge router routing tables.

Create static routes to all internal networks and a default route to the internet.

Check the statistics on the default route for oversaturation.

133. What is the effect of entering the ip dhcp snooping configuration command on a switch?

It enables DHCP snooping globally on a switch.

It enables PortFast globally on a switch.

It disables DTP negotiations on trunking ports.

It manually enables a trunk link.

134. An administrator notices that large numbers of packets are being dropped on one of the branch routers. What should be done or checked?

Check the routing table for a missing static route.

Create static routes to all internal networks and a default route to the internet.

Create extra static routes to the same location with an AD of 1.

Check the statistics on the default route for oversaturation.

135. What are two switch characteristics that could help alleviate network congestion? (Choose two.)

frame check sequence (FCS) check

136. What is a result of connecting two or more switches together?

The size of the broadcast domain is increased.

The number of broadcast domains is increased.

The number of collision domains is reduced.

The size of the collision domain is increased.

138. Branch users were able to access a site in the morning but have had no connectivity with the site since lunch time. What should be done or checked?

Use the “show ip interface brief” command to see if an interface is down.

Verify that the static route to the server is present in the routing table.

Check the configuration on the floating static route and adjust the AD.

Create a floating static route to that network.

139. What is the effect of entering the switchport port-security configuration command on a switch?

It enables port security on an interface.

It dynamically learns the L2 address and copies it to the running configuration.

It enables port security globally on the switch.

It restricts the number of discovery messages, per second, to be received on the interface.

140. A network administrator is configuring a WLAN. Why would the administrator use multiple lightweight APs?

to facilitate group configuration and management of multiple WLANs through a WLC

to centralize management of multiple WLANs

to monitor the operation of the wireless network

to provide prioritized service for time-sensitive applications

141. Refer to the exhibit. PC-A and PC-B are both in VLAN 60. PC-A is unable to communicate with PC-B. What is the problem?

The VLAN that is used by PCA is not in the list of allowed VLANs on the trunk.

The native VLAN should be VLAN 60.

The native VLAN is being pruned from the link.

The trunk has been configured with the switchport nonegotiate command.

142. A network administrator is configuring a WLAN. Why would the administrator use RADIUS servers on the network?

to restrict access to the WLAN by authorized, authenticated users only

to centralize management of multiple WLANs

to facilitate group configuration and management of multiple WLANs through a WLC

to monitor the operation of the wireless network

143. What is the effect of entering the switchport mode access configuration command on a switch?

It disables DTP on a non-trunking interface.

It enables BPDU guard on a specific port.

t manually enables a trunk link.

145. A network administrator is configuring a WLAN. Why would the administrator disable the broadcast feature for the SSID?

to eliminate outsiders scanning for available SSIDs in the area

to centralize management of multiple WLANs

to facilitate group configuration and management of multiple WLANs through a WLC

to provide prioritized service for time-sensitive applications

146. Refer to the exhibit. An administrator is attempting to install an IPv6 static route on router R1 to reach the network attached to router R2. After the static route command is entered, connectivity to the network is still failing. What error has been made in the static route configuration?

The next hop address is incorrect.

The destination network is incorrect.

The network prefix is incorrect.

147. What action takes place when a frame entering a switch has a unicast destination MAC address that is not in the MAC address table?

The switch will forward the frame out all ports except the incoming port.

The switch updates the refresh timer for the entry.

The switch resets the refresh timer on all MAC address table entries.

The switch replaces the old entry and uses the more current port.

148. A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Check the configuration of the exit interface on the new static route.

Create a floating static route to that network.

Check the configuration on the floating static route and adjust the AD.

Verify that the static route to the server is present in the routing table.

149. What is the effect of entering the ip arp inspection vlan 10 configuration command on a switch?

It enables DAI on specific switch interfaces previously configured with DHCP snooping.

It specifies the maximum number of L2 addresses allowed on a port.

It enables DHCP snooping globally on a switch.

It globally enables BPDU guard on all PortFast-enabled ports.

151. A network administrator is configuring a WLAN. Why would the administrator apply WPA2 with AES to the WLAN?

to provide privacy and integrity to wireless traffic by using encryption

to reduce the risk of unauthorized APs being added to the network

to centralize management of multiple WLANs

to provide prioritized service for time-sensitive applications

152. Users on a LAN are unable to get to a company web server but are able to get elsewhere. What should be done or checked?

Verify that the static route to the server is present in the routing table.

Ensure that the old default route has been removed from the company edge routers.

Check the configuration on the floating static route and adjust the AD.

Create a floating static route to that network.

154. What is the effect of entering the ip dhcp snooping limit rate 6 configuration command on a switch?

It restricts the number of discovery messages, per second, to be received on the interface.

It displays the IP-to-MAC address associations for switch interfaces.

It enables port security globally on the switch.

It dynamically learns the L2 address and copies it to the running configuration.

155. A network administrator is configuring a WLAN. Why would the administrator change the default DHCP IPv4 addresses on an AP?

to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range

to eliminate outsiders scanning for available SSIDs in the area

to reduce the risk of unauthorized APs being added to the network

to reduce the risk of interference by external devices such as microwave ovens

156. What is the effect of entering the ip arp inspection validate src-mac configuration command on a switch?

It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.

It displays the IP-to-MAC address associations for switch interfaces.

It enables portfast on a specific switch interface.

Finale Exam 100-170

Authored by мадияр алимов

History, Science

10th Grade

Used 12+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View
Student View

65 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

101. What protocol or technology uses source IP to destination IP as a load-balancing mechanism?

VTP

DTP

STP

EtherChannel

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

102. What protocol should be disabled to help mitigate VLAN attacks?

CDP

ARP

STP

DTP

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

103. What protocol or technology requires switches to be in server mode or client mode?

EtherChannnel

STP

VTP

DTP

MULTIPLE SELECT QUESTION

45 sec • 1 pt

104. What are two reasons a network administrator would segment a network with a Layer 2 switch? (Choose two.)

to create fewer collision domains

to eliminate virtual circuits

to isolate ARP request messages from the rest of the network

to isolate traffic between segments

to enhance user bandwidth

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

105. What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server?

a static route

the ipv6 route ::/0 command

the ip routing command

the ipv6 unicast-routing command

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

106. A network administrator is using the router-on-a-stick model to configure a switch and a router for inter-VLAN routing. What configuration should be made on the switch port that connects to the router?

Configure it as a trunk port and allow only untagged traffic.

Configure the port as an access port and a member of VLAN1.

Configure the port as a trunk port and assign it to VLAN1.

Configure the port as an 802.1q trunk port.

MULTIPLE SELECT QUESTION

45 sec • 1 pt

107. What are three techniques for mitigating VLAN attacks? (Choose three.)

Use private VLANs.

Enable BPDU guard

Enable trunking manually

Disable DTP.

Set the native VLAN to an unused VLAN.

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Microsoft

or continue with

Facebook

Apple

Others

By signing up, you agree to our Terms of Service & Privacy Policy

Already have an account?

Similar Resources on Wayground

64 questions

AP Government Unit 1 Test

Quiz

•

9th - 12th Grade

68 questions

ÔN KT GIỮA KÌ 2- SỬ 10--2023

Quiz

•

10th Grade

68 questions

Governments of Southwest Asia

Quiz

•

7th - 10th Grade

64 questions

Articles of Confederation/Shays' Rebellion/Constitutional Convention

Quiz

•

5th - 11th Grade

68 questions

Science at Work - Chapter 1 - Lvl1

Quiz

•

6th - 12th Grade

61 questions

KOREA!

Quiz

•

6th - 12th Grade

70 questions

Unit 4 Practice quiz astrophysics

Quiz

•

9th - 10th Grade

70 questions

Metals Non-metals & Metalloids

Quiz

•

7th Grade - University

Popular Resources on Wayground

10 questions

Safety Day 2026 – Student Review

Quiz

•

9th Grade

21 questions

Continents and Oceans

Quiz

•

6th Grade

20 questions

Parts of Speech

Quiz

•

5th Grade

16 questions

Subject & Predicate

Quiz

•

5th Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

12 questions

Map Skills

Quiz

•

3rd Grade

22 questions

Continents and Oceans

Quiz

•

5th Grade

15 questions

Rounding Decimals

Quiz

•

5th Grade

Discover more resources for History

25 questions

The American Revolution

Quiz

•

7th - 10th Grade

15 questions

The Bill of Rights

Quiz

•

8th - 12th Grade

15 questions

Ancient Rome

Quiz

•

7th - 10th Grade

16 questions

Students of Civics Unit 2: The Constitution

Quiz

•

7th - 11th Grade

10 questions

Exploring the 7 Principles of the Constitution

Interactive video

•

6th - 10th Grade

10 questions

Significance of the Declaration of Independence

Interactive video

•

6th - 10th Grade

10 questions

Exploring the Age of Exploration

Interactive video

•

6th - 10th Grade

10 questions

French and Indian War

Interactive video

•

9th - 10th Grade