Quiz about BLOCK 2 GENERAL SCIENCE II REVIEW (IN-PROGRESS))

Question 1

What is this drawing in the picture...

Accepted Answer

Assembly Drawing

Answer

Detail Drawing

Answer

Installation Drawing

Question 2

What is this drawing in the picture...

Accepted Answer

Installation Drawing

Answer

Assembly Drawing

Answer

Detail Drawing

Question 3

What is the drawing in this picture...

Accepted Answer

Detail Drawing

Answer

Installation Drawing

Answer

Assembly Drawing

Question 4

What is the name of this diagram?

Accepted Answer

SCHEMATIC DIAGRAM

Answer

TITLE DIAGRAM

Answer

WIRE DIAGRAM

Answer

PICTORIAL DRAWING

Question 5

What are zones?

Accepted Answer

Used to locate parts, sections, or alternate views of a drawing

Answer

Used to locate parts of a sectional drawing to alternate views of a large drawing

Answer

Used to locate parts, sections, and large drawings

Answer

Used to locate parts and sections

Question 6

Where does the engine pump receive fluid from?

Accepted Answer

The Reservior

Answer

The Hand Pumps

Answer

The Vent Line

Question 7

Under which condition will the warning horn be connected to ground through both gear switches when the throttles are closed?

Accepted Answer

Left gear up and right gear down

Answer

Both gears down and the control value in neutral

Answer

Right gear up and left gear down

Question 8

What does a hydraulic system schematic typically indicate?

Accepted Answer

The direction of fluid flow through the system

Answer

The specific location of the individual components within the aircraft

Answer

The pressure in the pressure lines, in the return lines, and in system components

Question 9

Zone numbers are read from

Accepted Answer

Right to left

Answer

Left to right

Answer

Top to bottom

Question 10

Parts numbered in the title block can be located on the drawing by finding the numbers in squares along the

Accepted Answer

Lower border

Answer

Upper border

Answer

Centerline border

Question 11

The sum of the plus and minus allowance figures is called

Accepted Answer

Tolerances

Answer

Allowances

Answer

Total results

Question 12

All changes to approved drawings must be carefully noted on the

Accepted Answer

All existing prints of the drawing.

Answer

First page existing prints of the drawing.

Answer

Second page existing prints of the drawing.

Question 13

The universal numbering system provides a means of identifying standard drawing sizes. Each drawing number consists of how many numbering digits?

Accepted Answer

Six or seven digits

Answer

Four or five digits

Answer

Ten digits

Question 14

Numbers that appears in the title block refer you to the numbers of other prints are called

Accepted Answer

Reference numbers

Answer

Station numbers

Answer

Dash numbers

Question 15

A description of a single part, describing by lines, notes, and symbols the specification for size, shape, material, and methods of manufacture to be used in making the part is called

Accepted Answer

Detail Drawing

Answer

Assembly Drawing

Answer

Installation Drawing

Question 16

When seen on a aircraft drawing, what does the application refer to?

Accepted Answer

To a specific aircraft

Answer

To a particular section

Answer

To a specific drawing

Question 17

A description of an object made up of two or more parts and its purpose is to show the relationship of the various parts, is what kind of a drawing is it?

Accepted Answer

Assembly Drawing

Answer

Installation Drawing

Answer

Detail Drawing

Question 18

Drawings should be handled carefully as they are

Accepted Answer

expensive and valuable

Answer

valuable and inexpensive

Answer

expensive and invaluable

Question 19

A section drawn directly on the exterior view shows the shape of the cross section of a part is called

Accepted Answer

Revolved Section

Answer

Half Section

Answer

Removed Section

Question 20

To protect drawings from damage

Accepted Answer

All the above

Answer

Never spread them on the floor

Answer

Hands should be free of oil, grease, and avoid smudges

Question 21

What type of line is normally used in a mechanical drawing or blueprint to represent an edge or object not visible to the viewer?

Accepted Answer

Medium weight dashed line

Answer

Medium solid line

Answer

Alternate short and long dashed line.

Question 22

A specific measured distance from the datum of some other point identified by the manufacture, to a point in or on the aircraft is called a?

Accepted Answer

Station number

Answer

Zone number

Answer

Reference number

Question 23

Which statement is true regarding an orthographic projection?

Accepted Answer

1 view, 2 view, & 3 view drawings are the most common.

Answer

There always at least two views.

Answer

It could have as many as eight views.

Question 24

A line used to show an edge which is not visible is a?

Accepted Answer

Hidden line.

Answer

Phantom line.

Answer

Break line.

Question 25

For sketching purposes, almost all objects are composed of one or some combination of six basic shapes which are?

Accepted Answer

Triangle, Circle, Cube, Cylinder, Cone, and Sphere

Answer

Angle, Arc, Line, Plane, Square, and Circle.

Answer

Triangle, Plane, Circle, Line, Square, and Sphere

Question 26

What should be the first step of the procedure in sketching an aircraft wing skin repair?

Accepted Answer

Block in the views.

Answer

Draw heavy guidelines.

Answer

Lay out the repair.

Question 27

What is the class of working drawing that is the description/depiction of a single part?

Accepted Answer

Detail drawing.

Answer

Installation drawing.

Answer

Assembly drawing.

Question 28

Zone numbers on aircraft blueprints are used to?

Accepted Answer

Locate parts, sections, and views on large drawings

Answer

Locate parts, views on larger drawings

Answer

Locate parts and Sections

Question 29

When reading a blueprint, a dimension is given as 4.387 inches +.005 -.002. What is the minimum acceptable size?

Accepted Answer

4.385

Answer

4.39

Answer

4.392

Question 30

When reading a blueprint, a dimension is given as 4.389 inches +.005 -.002. What is the maximum acceptable size?

Accepted Answer

4.394

Answer

4.387

Answer

4.39

Answer

4.392

Question 31

True or false. Schematic diagrams indicate the location of components with respect to each other within the system.

Accepted Answer

True

Answer

False

Question 32

What would be the last step of the procedure in sketching an aircraft wing skin repair?

Accepted Answer

Add the dimension

Answer

Add the aircraft wing

Answer

Add the scale

Question 33

True or False. A measurement should not be scaled from an aircraft print because the paper shrinks or stretches when the print is made.

Accepted Answer

True

Answer

False

Question 34

What type of diagram is used to explain a principle of operation, rather than show the parts as they actually appear?

Accepted Answer

A Schematic diagram

Answer

Diagram

Answer

A Flow diagram

Question 35

Working drawings may be divided into three classes. They are ______ drawings, _______ drawings, and _______ drawings

Accepted Answer

Instillation, Detail, and Assembly

Answer

Detail, Assembly, and Orthographic

Answer

Detail, Assembly, and Sectional

Answer

Detail, Assembly, and half

Question 36

There are 4 types of pictorial drawings used frequently by aircraft engineers and technician and they are:

Accepted Answer

Perspective, Isometric, Oblique and Exploded View

Answer

Full section, Half section, Revolved section and Removed section

Answer

Detail Drawing, Assembly Drawing, Installation Drawing and Sectional View Drawings

Question 37

What drawing are useful in showing the general appearance of an object and are extensively with orthographic projection drawings

Accepted Answer

Pictorial Drawings

Answer

Oblique Drawings

Answer

Isometric Drawings

Question 38

An object as it appears to the eye, but it is not satisfactory for showing complex forms and shapes is what kind of drawings

Accepted Answer

Pictorial Drawings

Answer

Exploded View Drawings

Answer

Perspective Drawings

Question 39

What view show only a part of the object, but in greater detail and to a longer scale than the principal view?

Accepted Answer

Detail View

Answer

One - View

Answer

Two - View

Question 40

When space is limited and two views must be shown, symmetrical object are often represented by

Accepted Answer

half view

Answer

full view

Answer

sectional view

Question 41

What types of drawings are commonly used for objects of uniform thickness, such as gaskets, shims, and plates

Accepted Answer

One - View

Answer

Two - View

Answer

Detail View

Question 42

What types of drawing are commonly used for cylindrical, spherical, or square parts if all the necessary dimensions can be properly shown?

Accepted Answer

One - View

Answer

Two - View

Answer

Detail View

Question 43

What types of view shows an object as it appears to an observer, and that some of the lines of an object are not parallel and therefore the actual angles and dimensions are not accurate.

Accepted Answer

Perspective View

Answer

Isometric View

Answer

Detail View

Question 44

What types of view uses a combination of the views of an orthographic and tilts the object forward so that portions of all three views can be seen in one view?

Accepted Answer

Isometric View

Answer

Perspective View

Answer

Oblique View

Question 45

Unlike a perspective drawing where lines converge and dimensions are not true, lines in an isometric drawing are parallel and dimensioned as they are to what

Accepted Answer

orthographic projection

Answer

perspective drawings

Answer

oblique drawings

Question 46

What drawing has two of the three drawing axes and is always at the right angles to each other?

Accepted Answer

Oblique Drawing

Answer

Perspective Drawing

Answer

Detail Drawing

Question 47

What view drawing is a pictorial drawing of two or more parts that fit together as an assembly.

Accepted Answer

Exploded View

Answer

Detail view

Answer

Installation View

Question 48

What is it call that define a graphic representation of an assembly or system and expresses the methods or principles of operation

Accepted Answer

Diagrams

Answer

Troubleshooting flowchart

Answer

Nomogram

Question 49

Diagrams that are used extensively in aircraft maintenance and repair manuals, and are invaluable in identifying and locating components and understanding the operation of various systems are what type of diagrams?

Accepted Answer

Installation Diagrams

Answer

Schematic Diagrams

Answer

Assembly Diagrams

Question 50

What diagrams show the principal of operation of an aircraft system and are often used for troubleshooting and training purposes?

Accepted Answer

Schematic Diagrams

Answer

Installation Diagrams

Answer

Assembly Diagrams

Question 51

Individual components that are drawn as a rectangle with lines connecting it to other components that it interfaces with during operation are what type of diagrams?

Accepted Answer

Block Diagrams

Answer

Step by step diagram

Answer

Wiring Diagrams

Question 52

What diagrams show the electrical wiring and circuitry, coded for identification, of all the electrical appliances and devices used on aircraft?

Accepted Answer

Wiring Diagrams

Answer

Step by step diagram

Answer

Troubleshooting Flowchart

Question 53

There are two types of flow charts most frequently used in the aviation industry and they are

Accepted Answer

troubleshooting & logic flowcharts

Answer

Fluid & Pneumatic flowcharts

Answer

Nomograms & graphically flowcharts

Answer

All of the above

Question 54

Flowchart that used standardized symbols to indicate specific types of logic gates and their relationship to other digital devices in a system is what type of flowchart is it?

Accepted Answer

Logic flowcharts

Answer

Pneumatic flowcharts

Answer

Fluid flowcharts

Question 55

What are used to show dimensions and hidden surfaces and to indicate centers?

Accepted Answer

Lines

Answer

Lines & Symbols

Answer

Symbols & Graphs

Question 56

Help locate a point and are mentally drawn as a horizontal or vertical line from letters and numerals

Accepted Answer

Zone numbers

Answer

Zones

Answer

Copy numbers

Answer

Bill of material

Question 57

A list of materials and parts necessary for fabrication or assembly of a component or system often included on a drawing

Accepted Answer

Bill of material

Answer

Drawing Standards

Answer

Materials

Answer

Title blocks

Question 58

A specific measured distance from the datum or some other point identified by the manufacturer, to a point

in or on the aircraft is called a

Accepted Answer

Station number

Answer

Zone number

Answer

Reference Number

Question 59

What type of drawing line consists of alternating long and short lines?

Accepted Answer

Center

Answer

Hidden

Answer

Dimension

Question 60

A line used to show an edge which is not visible is a

Accepted Answer

Hidden line

Answer

Phantom line

Answer

Break line

Question 61

(1) Schematic diagrams indicate the location of individual components in the aircraft

(2) Schematic diagrams indicate the location of components with respect to each other within the system

Accepted Answer

both 1 and 2 are true

Answer

only 2 is true

Answer

only 1 is true

Question 62

What are the proper procedural steps for sketching repairs and alterations?

Accepted Answer

3, 1, 4, and 2

Answer

4, 2, 3, and 1

Answer

1, 3, 4, and 2

Question 63

What is the next step required for a working sketch of the illustration?

Accepted Answer

Add notes, dimensions, title, and date

Answer

Sketch extension and dimension lines

Answer

Darken the object outlines

Question 64

In a sectional view drawing, what section illustrate particular parts of an object?

Accepted Answer

Removed

Answer

Revolved

Answer

Half

SCHEMATIC DIAGRAM

WIRE DIAGRAM

PICTORIAL DRAWING

Create a free account and access millions of resources

Popular Resources on Wayground

Discover more resources for Science