1. From where you can select frequencies for radio systems? (level 2)

B. Radio Management Panels (RMPs),

A. Audio Control Panels (ACPs),

C. Multipurpose Control and Display Units (MCDUs).

1. How is the audio signal from acoustic equipment connected to AMU (level 2)

C. Audio signal from acoustic equipment is not connected to AMU

1. If the flight crew needs to maintain contact and communicate with the mechanic, the flight crew can push: (level 2)

B. The MECH pushbutton on the CALLS panel on the overhead,

A. The GROUND pushbutton on the CALLS panel on the overhead,

C. The MECH transmission key and reception knob on Audio Control Panels (ACPs)

1. The INT/RAD selector switches to the INT position: (level 2)

A. This position enables permanent use of the flight interphone without any further reaction and whatever radio key is selected.

B. This position acts like the selection of the hand microphone pushbutton or the Push To Talk trigger on the side-stick.

C. This position is momentary contact to passenger address.

1. The INT/RAD selector switch in INT position, when can direct flight interphone transmission be allowed? (level 2)

C. No transmission key is selected or the transmission key is selected and no Push-To-Talk switch is activated

A. No transmission key is selected.

B. The transmission key is selected and no Push-To-Talk switch is activated

1. What is reason for the service interphone system is disabled when the weight off wheels? (level 2)

B. To eliminate potential static noise generated and amplified through the AMU due to the length of wires acting as antenna into the audio system.

A. It might not be necessary to communicate between personnel at various points around the aircraft when jacking the aircraft

C. To protect static discharger.

1. For RMP interface, what are the dialog buses used for? (level 3)

A. Exchange of information between the three RMPs.

B. To transmit data to transceiver.

1. What happens if RMP1 fails? (level 3)

C. All communication frequencies can be controlled by using RMP2 or RMP 3 .

A. The communication systems are inoperative

B. VHF1 frequencies cannot be controlled.

1. What is purpose of RMP (level 3)

B. Selection of radio communication frequencies and selection of radio navigation frequencies as back−up of the Flight Management Guidance Computers (FMGCs).

A. Selection of radio communication frequencies and selection of interphone system frequencies

C. Selection of radio communication frequencies

1. The audio switching selector is used for the: (level 3)

C. Reconfiguration of channels, in case of ACP failure.

A. Selection of various items of acoustic equipment.

B. Control of the received audio signal levels.

1. What is function of the AUDIO SWITCHING selector? (level 3)

A. Is used in case of communication failure on CAPT or F/O channels.

B. Is used in case of boomset failure on CAPT or F/O side.

C. Is used in case of handset failure on CAPT or F/O side.

1. How can the Captain control audio when ACP 1 failed: (level 3)

C. Use ACP 3 by using “AUDIO SWITCHING”

1. The audio switching selector is used in case of communication failure on CAPT or F/O channels. when switch set to CAPT 3: (level 3)

A. The CAPT will use the 3rd occupant ACP. The 3rd occupant audio equipment cannot be used.

B. The CAPT will use the 3rd occupant ACP. The 3rd occupant audio equipment still can be used.

C. The 3rd occupant will use ACP 1.

1. How is CAPT’s acoustic equipment audio line connected when AUDIO SWITCHING selector is switched to CAPT 3 position: (level 3)

B. CAPT’s acoustic equipment audio line is connected to AMU

A. CAPT’s acoustic equipment audio line is connected to 3rd occupant ACP

C. CAPT’s acoustic equipment audio line is connected to 3rd occupant RMP

1. When is the muting circuit operative? (level 3)

C. The muting circuit is operative when any microphone is keyed to transmit

A. The muting circuit always mutes the audio output

B. The muting circuit is operative only with the hand microphone selection

1. What is purpose of muting circuit: (level 3)

A. To avoid acoustic coupling between the loudspeakers and the microphones.

B. To avoid acoustic coupling between the Flight Warning Computer (FWC) audio outputs and the microphones.

C. To avoid noisy from high power engine running.

1. The high frequency (HF) system serves for: (level 3)

A. All long-distance voice communications.

B. All short-distance voice communications.

1. The HF system used for: (level 3)

A. Long-distance communications,

B. Short-distance communications,

C. Medium-distance communications,

1. The very high frequency (VHF) system serves for: (level 3)

A. Short range voice communications.

B. Long-distance voice communications

C. Any range voice communications

1. The VHF system used for: (level 3)

B. Short-distance communications,

A. Long-distance communications,

C. Medium-distance communications,

The purpose of the SELCAL system is to give (level 3)

Visual and aural indications to the crew, concerning calls received from ground stations through VHF and HF systems.

Voice communications between different aircraft (in flight or on the ground), or between the aircraft and one or several ground stations.

A/C identification for ATC ground stations.

The reset key on ACPS is used to: (level 3)

Cancel the previous selections.

The SELCAL code is used for: (level 3)

Receive calls from ground station

Receive the call from cabin attendant stations

SELCAL provides: (level 3)

Visual and aural indication of calls received from ground stations

Visual and aural indication of calls received from other aircrafts

Visual and aural indication of calls received from ground stations and other aircrafts

The ACPs reset key is used to (level 3)

Extinguish the buzzer sound when the call is coming

Extinguish all the lighted calls

When do CALL lights of transmission key on ACP go off automatically? (level 3)

When transmission on the called channel is done

After 60 seconds if the call is not cancelled by the RESET key

CALL lights of transmission key on ACP can not go off automatically.

Which requisition must be meet to receive the SELCAL CALL? (level 3)

The code of SELCAL signal and the code programmed on the SELCAL code panel are agree.

At lease a reception knob on an ACP pops out (reception channel is selected).

At lease a transmission key on an ACP is pressed.

test23

Authored by vinh vũ

Science

1st Grade

Used 15+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

150 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. On RMP, the LCD active window displays the: (level 2)

A. Standby frequency or the course in back-up navigation mode.

B. Operational frequency.

C. Operational frequency or the course in back-up navigation mode.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. What is function of Push To Talk (PTT) button (level 2)

A. Connect audio signal to loudspeaker

B. Connect audio signal to transceiver

C. Connect audio signal to transceiver and switch reception to transmission

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. The audio control panels (ACP) are used for the: (level 2)

A. Control of the received audio signal levels.

B. Selection of communication systems (in transmission and reception) and for the control of the received audio signal levels.

C. Selection of communication systems (in transmission and reception)

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. The flight interphone system allows communication between the: (level 2)

A. Flight crew members

B. Flight crew and the ground mechanic only.

C. Flight crew members, and between the flight crew and the ground mechanic.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. How many transmission channel can be selected at a time: (level 2)

A. Two

B. Three

C. Only one

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. Three green bars illuminated on the ACP’S VHF 2 key means: (level 2)

A. VHF 2 operation is correct

B. A SELCAL is received on VHF 2

C. VHF 2 is selected in transmission

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

1. The radio management panels (RMPs) are used for the selection of (level 2)

A. Radio communication.

B. Navigation frequencies.

C. Radio communication and navigation frequencies.

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Popular Resources on Wayground

10 questions

5.P.1.3 Distance/Time Graphs

Quiz

•

5th Grade

10 questions

Fire Drill

Quiz

•

2nd - 5th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

22 questions

School Wide Vocab Group 1 Master

Quiz

•

6th - 8th Grade

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

20 questions

Inferences

Quiz

•

4th Grade

12 questions

What makes Nebraska's government unique?

Quiz

•

4th - 5th Grade

Discover more resources for Science

14 questions

Physical Properties Of Matter

Quiz

•

KG - 1st Grade

10 questions

Gravity and Static Electricity TCAP Review

Presentation

•

1st - 5th Grade

6 questions

CA4 Science

Presentation

•

1st - 5th Grade

10 questions

Exploring Food Webs and Energy Flow

Interactive video

•

1st - 5th Grade

10 questions

Exploring Food Chains and Webs in Ecosystems

Interactive video

•

1st - 5th Grade

7 questions

Sorting and Classifying Items

Quiz

•

1st Grade

10 questions

Identifying Physical and Chemical Changes

Interactive video

•

1st - 5th Grade

15 questions

Electricity TCAP Review

Presentation

•

1st - 5th Grade

test23

1. On RMP, the LCD active window displays the: (level 2)

1. What is function of Push To Talk (PTT) button (level 2)

1. The audio control panels (ACP) are used for the: (level 2)

1. The flight interphone system allows communication between the: (level 2)

1. How many transmission channel can be selected at a time: (level 2)

1. Three green bars illuminated on the ACP’S VHF 2 key means: (level 2)

1. The radio management panels (RMPs) are used for the selection of (level 2)

1. From where you can select frequencies for radio systems? (level 2)

1. How many transmission key can be selected at a time? (level 2)

1. How is the audio signal from acoustic equipment connected to AMU (level 2)

Access all questions and much more by creating a free account

Popular Resources on Wayground

Discover more resources for Science