GLOBAL MUTICAST HAS BEEN CONFIGURED FOR MULTICAST-MULTICAST. BUT MULTICAST IS NOT FUCTIONING ON ANY OF THE WLANS IN THE NETWORK, WHICH ACTION ENABLES MULTICAST?

ENABLED THE MULTICAST VLAN FEATURE

SET THE RADIO POLICY TO ALL ON THE WLAN

ENABLE WLAN ADVANCED SETTINGS TO SUPPORT MULTICAST-MULTICAST MODE

an engineer configures qos on aireos wlc b8.5. the engineer configures a wlan for voice traffic and must give a higher priority to WMM clients that non-wmm clients, which two configurations should be performed?

set multicast default priority to voice

implement the platinum QoS profile

select video from the unicast default priority drop down menu

set unicast default priority planinum

After the rogue reports from Cisco Prime Infrastructure are reviewed, it is determined that the automatic rogue mitigation is not working as planned. Which security measure must be taken to help prevent rogue APs from being plugged into the network?

A. Apply port security to the switch.

B. Add a MAC filter to the switch.

C. Apply a different version of spanning tree.

D. Apply an IP access list to ports.

An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications: • Primary CMX IP address: 192.168.1.4/24 • Secondary CMX IP address: 192.168.4.4/24 • Virtual IP address: 192.168.4.1/24 During testing, the engineer discovers that the failover fails. Which action resolves the issue?

D. Place the primary CMX IP address and the secondary CMX IP address in the same subnet.

A. Place the primary CMX IP address and the virtual IP address in the same subnet.

B. Place the secondary CMX IP address and the virtual IP address in different subnets.

C. Use a virtual IP address with CMX Layer 3 high availability.

An engineer supports the network infrastructure within a football stadium, and there is a new requirement to send media over wireless. Multicast direct must be used to optimize multicast communication over wireless. Which multicast address must be added in the media stream configuration to meet this requirement?

B. video server multicast destination address

A company has a Cisco wireless network with Cisco ISE. The company wants to allow employees to use their personal mobile devices on the wireless network. The company wants to allow access to the network only if the devices meet certain criteria. To meet the requirement, the company asked a network engineer to create a native supplicant profile. Which two fields must be configured when the profile is created? (Choose two.)

B. Allowed Protocol (Ms-CHAPv2/ EAP-FAST)

E. Allowed Protocol (LEAP/ EAP-TTLS)

A wireless network has two RF groups where Cisco WLCs are joined. APs are associated with different controllers using the round-robin approach. Rogue containment must be deployed in all controllers, but the network must not be affected by any RRM neighbor packets sent by friendly APs. Which AP authentication protection type must be enabled?

B. AP Wireless Protection Rules

AN ENGINEER COMPLETED THE CONFIGURATION OF A WIRELESS CONTROLLER. WHAT ARE TWO RESULTS OF THIS CONFIGURATION?

Cisco discovery is globally enabled and it can be turned off for a specific Ap, if desired

AP's inherit the credentials from this global configuration on the WLC, unless specifically overridden on an AP level

APS Joined to this WLC can be accessed through the default credentials

global configuration for AP's is AP group specific in the WLC

The changes on this page only apply to AP's that would associate to WLC in the future

a customer implements AVC on the AireOS controllers. all of the netflow data is configured for export to cisco prime insfraestructure to be analyzed for a specified period. during testing, no data is reported from the controllers. which two configurations must be applied for the data to be exported? choose two

config flow add monitor AVC_test exporter Export_to_prime_Infraestructure

config flow create exporter Export_to_prime_Infraestructure 10.20.30.6 port 8080

config flow add monitor avc_test

config flow create exporter Export_to_prime_Infraestructure 10.20.30.6 port 9991

an engineer receives a report that a client cannot authenticate via phone in a secure WLAN. THE PHONE USES LAYER 2 SECURITY WPA2, AND OTHER CLIENTS CAN AUTHENTICATE SUCCESFULLY. THE ENGINEER ISSUES THE (CONTROLLER)>DEBUG CLIENT 64:89:9A:31:7F:A1 and (CONTROLLER)> debug aaa al enable commands in the controller and sees this output , what are the two sources of this issue? (choose two)

The incorrect EAP method was configured on the client device

An invalid user account or passowrd was used

certificate services are not working properly

the server certificate expired or not in use

Radius is incorrectly configured

AN ENGINEER MUST IMPLEMENT MULTICAST ON AIRE WLC V8.2 THAT HAS 200 LWAPS CONNECTED. RELIABLE RECEPTION IS A MAIN REQUIREMENT OF THIS IMPLEMENTATION. WHICH WIRELESS CONFIGURATION MUST BE PERFORMED?

DISABLE LOWER MANDATORY DATA RATES

DISABLE HIGHER MANDATORY DATA RATES

EN ENGINEER CONFIGURES AN ACL ON A CISCO WLC V8.7. THE ENGINEER MUST CONTROL IP TO THE CPU OF THE CONTROLLER. WHICH RULES SHOULD BE V4 TRAFFIC ADDED AT THE TOP OF THE ACL TO CONTROL IPV4 TRAFFIC?

DENY MOBILITY PORTS 16666,16667,16668

ALLOW MOBILITY PORTS 16666,16667,16668

ALLOW RRM PORTS 12124-12125 AND 12134-12135

A shopping center uses AireOS controllers with Cisco Wave 2 APs. A separate WLAN named Guest-012345678-WLAN is used for guest wireless clients. Management needs location analytics to determine popular areas. CMX must track only associated clients. What must be selected on the CMX server settings?

Enable Locally Administered MAC Filtering

A WIRELESS NETWORK HAS LIGHTWEIGHT APS DISTRIBUTED ON MULTIPLE BUILDINGS AND DIFFERENT AP GROUPS, AN ADMINISTRATOR REPORTED THAT APPLETV FROM ONE BULDING IS DISCOVERED IN OTHER BULDINGS AFTER IT IS QUERIED. WHY IS THIS HAPPENING?

no acl entry has been deployed to filter mDNS service advertisement between ap groups

LIGHWEIGHT APS INCORRECTLY FILTER mDNS service for each location

mDNS service is configured as a wireless service provider for user access

apple tv service is discovered as a wired service provider

an engineer must deply flexconnect aps to a branch office . if the connection to the WLC fails and 802.11x authentication is available, users must stay connected to the Ap . which flexconnect state should be implemented?

authentication central/switch local

authentication central/switch central

authentication local/switch local

authentication local/switch central

an engineer must enable location services using cisco dna space through a DNA space connector on a client located in the us. which two requirements are mandatory for a succesful implementation?(choose two)

ensure that the wireless controller API is accesible for the DNA space connector

Cisco DNA space connector must be able to reach out to https://connector.dnaspaces.io

the wireless controllers must enable cisco CMX connector

Cisco DNA spaces connector must connect to the wireless controllers

Cisco DNA space connector must be able to connect to wireless network

a company has an existing cisco wireless solutuin dedeployed to a remote bran d locatioon with centrally switched control and data traffic. a new solution us needed to locally switch client traffic when wifi is used only for vouce devices must be mapped to an onside new ssid that is voice vlan named vlan 25. which configuration on the switch interface that connects to the APs meets this requirement?

switchport mode trunk switchport trunk allowed vlan add vlan 25

switchport mode trunk switchport trunk native vlan 25

switchport mode access switchport access vlan 25

switchport mode access switchport access voice vlan 25

an engineer configures qos on an aireos wlc v8.5 the engineer configures a wlan for voice traffic and must set the data rates within the qos profile, how should the data rates be configured to ensure that the QoS PROFILE ALLOWS TRAFFIC TO AN FROM THE WIRELESS CLIENT?

THE BURST DATA RATE SHOULD BE GREATER THAN OR EQUAL TO THE AVERAGE DATA RATE.

THE BURST DATA RATE SHOULD BE SET A NON-ZERO VALUE

THE BURST DATA RATE SHOULD BE CONFIGURE D BEFORE THE AVERAGE DATA RATE

DATA RATES SHOULD BE APPLIED PER AP RADIO

<a target="_blank" rel="noopener noreferrer nofollow" class="link-style gL9Hy" href="https://www.google.com/search?sca_esv=7bed0de0dada41c5&rlz=1C1GCEA_enCR1024CR1024&sxsrf=ADLYWIJQAy_VRci1hNhfIrCd5cmCAZ-Ghg:1725225560775&q=you+are+seeing+an+excessive+number+of+rogue+AP+alarms+in+cisco+prime+infrastructure.+All+these+alarms+have+severity+level+of+minor.+which+two+actions+must+be+taken+to+make+more+efficient+use+of+rogue+AP+alarms?(choose+two)&spell=1&sa=X&ved=2ahUKEwjS_dOF1qKIAxWsRTABHQhgADMQkeECKAB6BAgJEAE">you are seeing an excessive number of rogue AP alarms in cisco prime infrastructure . All these alarms have severity level of minor. which two actions must be taken to make more efficient use of rogue AP alarms?(choose two)

Create and install a configuration template the modifies the minimum rogue detection RSSI of the controller to a stronger value

Create and install a configuration template to establish rogue rules that use specific criteria to declare APs as friendly rogues

disable rogue detection on the infraestructure APs that are detecting the rogue APs

delete the alarms. they do not return even if the same rogue ap is detected again

clear the alarms. they do not return even if the same rogue ap is detected again

which characteristic of multicast mode that affects the wireless network when configured on a Cisco WLC?

Packet replication is performed on the network

The controller sends every multicast packet associated APs

The controller sends multicast packets to a user group

Packet replication is performed on the controller

an engineer implements QoS on aire WOLC v8.3 when configuring AVC on a WLAN, the engineer must configure the appropoate AVC profile for a cisco wireless IP phone 8821. which command must be used?

config ave profile AUTO QOS-AVC-PROFILE rude add application cisco-phone-audio mark 46

config ave profile AUTO QOS-AVC-PROFILE rude add application cisco-phone-audio mark 56

config ave profile AUTO QOS-AVC-PROFILE rude add application cisco-phone-audio mark 48

config ave profile AUTO QOS-AVC-PROFILE rude add application cisco-phone-audio mark 41

an engineer is configuring wireless guests using CWA. when a device connects . it must be redirected to the Webauth, but this was failing. what must be configured for the device to be redirected correctly?

Configure ACL name on the anchor controller

Remove the CN entry from the SAN

a cisco wlc is deployed to a customer site. the customer provides a list of wired and wireless subnets that must be allowed to pass though the WLC, what is the path in the WLC user interface to create the access list?

security>access control lists> access control lists

Controller>interfaces<acl name drop-down list

security>access control lists>CPU access control list

WLANS<WLAN ID>ADVANCED>OVERRIDE interface ACL

THE REDIRECT ACL IS CONFIGURED ON CISCO CATALYST 9000-40 WLC version 17.3.3. The acl is pushed by cisco ISE version 3 for a CWA SSID implementation. the ip address 10.48.39.28 represents the ISE ip address , where must the ACL be applied?

On a new or existing authorization profile as cisco-av pair for URL redirect under policy elements

On a new or existing cisco-ac-pair dictionary under policy elements for URL redirect

On a new allowed protocol under authentication profile under policy elements for URL redirect

On an existing cisco-av-pair library condition under policy elements for URL redirect

100-517

Authored by Jeaustin Zumbado

Computers

1st Grade

Used 6+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

57 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

which protocol enables multicast traffic only on a specific wlan instead of the hole network?

TPC

DCA

WMM

WMF

MULTIPLE SELECT QUESTION

45 sec • 1 pt

An engineer has eight WLCs in a mobility group and must reduce the bandwidth consumed. Which two configuration items achieve this result? (Choose two.)

A. global multicast mode

B. mobility group unicast messaging

C. global unicast messaging

D. mobility group multicast messaging

E. global symmetric mobility messaging

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Split Tunneling must be configured for traffic sent by the client to be classified based on packet content, using an ACL. To accomplish this, the packets must be either locally switched from Cisco FlexConnect AP or centrally-switched over CAPWAP. Which type of ACL must be configured to accomplish this switching?

A. Interface

B. CPU

C. FlexConnect

D. WLAN

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A customer must use deep-packet inspection on the Cisco Catalyst 9800 Series Wireless Controller. The details must include all wireless client use details. Where must AVC be configured to meet this requirement?

A. AP join tag

B. policy profile

C. RF tag

D. WLAN

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

An engineer needs to configure the infrastructure for wireless clients to use IEEE 802.1X to the onboarding VLAN. After authentication and profiling, it must be determined if the client is a company device that is up-to-date. After this step, the device must connect to the corporate VLAN and access all resources. What must be implemented to meet these requirements?

A. Change of Authentication

B. Completion of Authentication

C. Change of Authorization

D. Completion of Authorization

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A customer recently upgraded the network to Cisco SD-Access. Cisco DNA Center manages the wireless network; all SSIDs are Fabric-enabled. Cisco DNA Center must be able to classify “Rogue on Wire" APs. Which action must the customer take?

A. Configure all access switches to be managed by Cisco DNA Center.

B. Allow SNMPv3 between Cisco DNA Center and access switches.

C. Connect APs to the network using a trunk port with native VLAN.

D. Disable all the DCA channels under RRM on the WLC.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

An engineer set up RADIUS for WLC management to harden the configuration. Read-only access must be provided to a user. Which Service-Type attribute must be configured on the RADIUS server to meet this requirement?

A. NAS Prompt

B. Administrative

C. Call Check

D. Callback Login

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

55 questions

on tap lop 10

Quiz

•

1st Grade

60 questions

PENILAIAN AKHIR TEORI SET A

Quiz

•

1st Grade

62 questions

ITIL V4 - QUIZ 5

Quiz

•

KG - Professional Dev...

60 questions

UML Final

Quiz

•

KG - Professional Dev...

52 questions

Predict the output of algorithm - recreate algorithm as progrm

Quiz

•

1st Grade

56 questions

Multiprocessor Systems Quiz

Quiz

•

1st Grade

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

10 questions

Probability Practice

Quiz

•

4th Grade

15 questions

Probability on Number LIne

Quiz

•

4th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

6 questions

Appropriate Chromebook Usage

Lesson

•

7th Grade

10 questions

Greek Bases tele and phon

Quiz

•

6th - 8th Grade

Discover more resources for Computers

12 questions

Presidents' Day

Quiz

•

KG - 5th Grade

20 questions

Telling Time to the Hour and Half hour

Quiz

•

1st Grade

10 questions

Exploring Rosa Parks and Black History Month

Interactive video

•

1st - 5th Grade

16 questions

Morning Math Review

Lesson

•

1st - 5th Grade

17 questions

Reading Comprehension

Quiz

•

1st - 4th Grade

16 questions

3D shapes (1st grade)

Quiz

•

1st Grade

20 questions

Place Value

Quiz

•

KG - 3rd Grade

6 questions

President's Day

Lesson

•

1st Grade

100-517

which protocol enables multicast traffic only on a specific wlan instead of the hole network?

An engineer has eight WLCs in a mobility group and must reduce the bandwidth consumed. Which two configuration items achieve this result? (Choose two.)

A customer must use deep-packet inspection on the Cisco Catalyst 9800 Series Wireless Controller. The details must include all wireless client use details. Where must AVC be configured to meet this requirement?

A customer recently upgraded the network to Cisco SD-Access. Cisco DNA Center manages the wireless network; all SSIDs are Fabric-enabled. Cisco DNA Center must be able to classify “Rogue on Wire" APs. Which action must the customer take?

An engineer set up RADIUS for WLC management to harden the configuration. Read-only access must be provided to a user. Which Service-Type attribute must be configured on the RADIUS server to meet this requirement?

The marketing department in a retail company has created a promotional video for the opening of a new branch store shp-GA4B6C860927AB. The video must be received by interested hosts only, over wireless multicast. What allows this feature?

Refer to the exhibit. An engineer must identify jammer devices on the wireless network. The AP must scan all configured channels. Which AP mode must be configured to accomplish this?

GLOBAL MUTICAST HAS BEEN CONFIGURED FOR MULTICAST-MULTICAST. BUT MULTICAST IS NOT FUCTIONING ON ANY OF THE WLANS IN THE NETWORK, WHICH ACTION ENABLES MULTICAST?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers