What causes expansion noise in hot water or central heating pipework?

Heated water passing through the pipes

Cold water passing through the pipes

Electrical current passing through the pipes

What should be inspected to address expansion noise in pipework?

Clips/brackets, notching, insulation and padding

What is another method to manage flow noise besides increasing pipe diameter?

Install a pressure reducing valve

Install a pressure increasing valve

What happens if a thermostat fails open in a hot water system?

The customer will have no hot water.

The temperature will continue to rise.

The water will become too cold.

The system will shut down completely.

What is a potential consequence of a thermostat failing closed?

The temperature will continue to rise to dangerous levels.

The water will become too cold.

The customer will have no water at all.

What is a common indicator of immersion element failure in a water heating system?

No hot water; fuse blowing; MCB tripping

In a direct cylinder, what happens when the immersion element fails?

The customer will have no hot water

What should be done to comply with Building Regulations Part P when replacing an immersion element?

Replace immersion, complying with Building Regulations Part P

Replace immersion without any regulations

What should be checked first if there is no hot water due to a heat source failure?

The fuse and time clock settings

What happens if the coil fails in the system described?

Water is forced into the primary system.

The system shuts down completely.

The pressure from the F&E cistern becomes greater.

What is an indicator of a coil failure in the system?

F&E overflow dripping and hot water discoloured.

Complete loss of water pressure.

What should be done if the coil fails?

Replace cylinder with a current approved part L cylinder.

Increase the pressure in the F&E cistern.

Turn off the system completely.

What issue occurs with a single feed cylinder when the air bubble is lost?

The hot water will be discoloured when drawn off.

The water will be clear when drawn off.

The pressure relief valve will not discharge.

The system will not need draining.

What happens with an unvented cylinder when the air bubble is lost?

The pressure relief valve will discharge when the water is heated.

The system does not need refilling.

The air bubble is automatically reinstated.

What is required in both cases of air bubble loss in the system?

The secondary system needs draining to the base of the hot water cylinder.

The system should be left as is.

The air bubble will automatically return.

The pressure relief valve should be replaced.

What is a sign that water is boiling in a heating system?

Steam is present in the loft area.

The water is cold when drawn off.

What should be done if old immersion heater thermostats are found?

Replace them with new immersions with a non self-resetting thermal cut out.

Increase the water temperature.

What is a common cause of cold water warming up in pipes?

Hot water pipes are installed below cold water pipes.

Cold water pipes are too far from hot water pipes.

Cold water pipes are insulated.

Hot water pipes are installed above cold water pipes.

According to BS8000 pt15, what should be done to prevent heat transfer between pipes?

Install cold pipes above hot pipes.

Insulate the cold water pipes only.

Use larger pipes for hot water.

What happens if the hot water cylinder overheats?

The vent pipe discharges into the CWSC.

The cold water pipe cools down.

What is a common cause of air locks in pipework systems?

Incorrect installation of pipework

What is an indicator of an air lock in a pipework system?

No flow of water or intermittent water flow

What should be done at the commissioning stage to prevent blockages?

Flush out the system to remove debris

Which of the following is NOT a recommended action to address blockages?

Trace draw off points and pipework

What is a common issue caused by limescale in hard water areas?

Blockages and reduced efficiency

What is a recommended solution for dealing with limescale?

Install a water softener or scale inhibitor

Flow Rate Inspection Quiz Quiz

57 questions

Show all answers

1.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What should be inspected if the flow rate is less than required?

Temperature settings on thermostat

Limescale blockages

Filters cleaned

Valves are fully operational

2.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which of the following is NOT a potential cause of poor flow rate?

Temperature settings on thermostat

Filters cleaned

Lubrication of parts

Pipe size too small

3.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is a potential cause of unbalanced pressure in manually controlled showers?

Properly adjusted thermostat

Clean filters

Debris blocking the feed pipework

Fully operational valves

4.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which of the following is NOT listed as a maintenance indicator for showers?

Temperature settings on thermostat

Limescale blockages

Regular paint touch-ups

Lubrication of parts

5.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What effect can damaged or squashed feed pipework have on a shower?

Increase water pressure

Decrease flow rate and temperature

Improve water quality

Enhance showerhead performance

6.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What can cause an isolation valve to pass water?

A new valve

A build-up of limescale, debris, de-zincification, or a damaged O ring

Regular maintenance

Proper lubrication

7.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which of the following is NOT a recommended maintenance step for valves?

Dismantle valve

Remove debris or lime scale

Paint the valve

Lubrication of parts

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

60 questions

Rules and Regulations Course Review

Quiz

•

9th - 12th Grade

60 questions

PENGAJIAN AM SEMESTER 1 THE CHAMPS

Quiz

•

1st Grade - University

52 questions

In, At, On - Prepositions of Time and Place

Quiz

•

7th - 12th Grade

54 questions

Animal Anatomy & Physiology

Quiz

•

9th - 12th Grade

59 questions

DOG ID

Quiz

•

12th Grade

57 questions

Cold Water - Mock Exam

Quiz

•

12th Grade - University

55 questions

PBMF Final Review 1st Semester

Quiz

•

9th - 12th Grade

62 questions

miraculous 🐞 ladybug

Quiz

•

KG - Professional Dev...

Popular Resources on Wayground

8 questions

Spartan Way - Classroom Responsible

Quiz

•

9th - 12th Grade

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

14 questions

Boundaries & Healthy Relationships

Lesson

•

6th - 8th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

3 questions

Integrity and Your Health

Lesson

•

6th - 8th Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

9 questions

FOREST Perception

Lesson

•

KG

20 questions

Main Idea and Details

Quiz

•

5th Grade

Discover more resources for Other

8 questions

Spartan Way - Classroom Responsible

Quiz

•

9th - 12th Grade

22 questions

El Imperfecto

Quiz

•

9th - 12th Grade

25 questions

Logos

Quiz

•

12th Grade

20 questions

Grammar

Quiz

•

9th - 12th Grade

18 questions

Mendelian Genetics

Quiz

•

10th - 12th Grade

22 questions

Regular Preterite -AR-ER-IR-

Quiz

•

12th Grade

20 questions

verbos reflexivos en español

Quiz

•

9th - 12th Grade

14 questions

Making Inferences From Samples

Quiz

•

7th - 12th Grade

Flow Rate Inspection Quiz

What should be inspected if the flow rate is less than required?

Which of the following is NOT a potential cause of poor flow rate?

What is a potential cause of unbalanced pressure in manually controlled showers?

Which of the following is NOT listed as a maintenance indicator for showers?

What effect can damaged or squashed feed pipework have on a shower?

What can cause an isolation valve to pass water?

Which of the following is NOT a recommended maintenance step for valves?

What is one cause of leaks in components according to the maintenance document?

Which of the following is a recommended action to address leaks?

What causes expansion noise in hot water or central heating pipework?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Other