In biologically contaminated fuel, corrosion takes place.

C. the bottom 2 inches of the tank.

The purpose of a scavenge system within a fuel system is.

C. to ensure that any water in the fuel is constantly dispersed thus reducing microbiological contamination.

A. to ensure that all unused fuel is returned to the tanks efficiently.

B. To prevent water flows to fuel tank

D. to ensure that all available fuel can be used

To shut-off the LP fuel supply to the engine for the purpose of engine removal you would.

A. close the cross-bleed valve.

The advantages of integral fuel tanks are that they.

B. use the maximum volume for fuel and have the minimum amount of weight.

A. are safer on fire hazard compare to others

C. are easier to design and construct and use the maximum volume of fuel.

D. are cheaper to manufacture, more durable and easier to maintain.

In a light fixed wing aircraft, the fuel warning light indicates.

D. ice blockage, filter popped or pump fail.

B. the tank does not pressurized.

C. Fuel is lower than normal level

A fuel tank suction valve will open when.

B. either the engine driven pump fails or booster pump fails.

C. the engine driven pump fails.

D. both the engine driven and booster pump fails

A check valve is fitted to a fuel jettison system to.

B. prevent the dumping of the outer tanks.

A. prevent the center from being defueled.

C. automatically stop the fuel jettison operation after a period of time.

The purpose of control cable regulators is to.

B. maintain preset cable tensions during flight.

C. compensate for low temperature only.

D. compensate for high temperature only.

A yaw damper gain could be fitted with.

B. increased sensitivity for increased speed.

A. decreases sensitivity for decreased speed.

C. decreases sensitivity for increased speed.

D. increased sensitivity for decreased speed.

With respect to flight spoilers, they.

A. can operate both on the ground and in flight.

In a fly-by-wire aircraft, what controls the roll spoilers?

B. Flight augmentation computer.

What is an aileron balance cable for?

A. To allow the cable to be tensioned.

B. To correct for wing heaviness.

C. To allow aircraft to fly hands off.

D. To correct for balancing aircraft.

A horn balance on a control will.

A. increase degree of movement at high speed.

B. decrease degree of movement at low speed.

C. decrease degree of movement at high speed.

D. increase degree of movement at low speed.

Differential aileron control will.

prevent yawing in conjunction with rudder input.

In an aircraft system employing balance tabs, the installation of external ground locks between control surface and balance tabs.

would not prevent the movement of the control column.

would prevent the movement of the control column.

is unnecessary since the system is irreversible.

A stick shaker is a device which

vibrates the control column near stalling speed.

gives a short period of landing.

helps extricate an aircraft from soft ground.

gives a short period of extra lift to assist take off.

The purpose of the servo valve in a power operated control is

to direct hydraulic fluid to the jack in response to the pilots control in cockpit.

to provide pressure to operate the control.

to revert the system to manual operation.

Differential aileron control will.

prevent yawing in conjunction with rudder input.

A servo tab is operated.

directly by the pilot to produce forces which in turn move the main control surfaces.

indirectly by the pilot to produce forces which in turn move the main control surfaces.

by a trim wheel and moves in the opposite direction to the main control surfaces when moved.

automatically, and moves in the same direction as the main control surfaces.

What type of packing’s should be used in hydraulic components to be installed in a system containing Skydrol?

Packing materials made for ester base fluids.

AN packing’s made of natural rubber.

AN packing’s made of neoprene.

What is the viscosity of hydraulic fluid?

The internal resistance of a fluid which tends to prevent it from flowing.

The increase in volume of a fluid due to temperature change.

The fluid's ability to resist oxidation and deterioration for long periods.

Which is a characteristic of petroleum base hydraulic fluid?

Flammable under normal conditions.

Compatible to natural rubber seals and packings.

Nonflammable under all conditions.

What is the main purpose of a pressurized reservoir in a hydraulic system?

Prevent hydraulic fluid from foaming.

Prevent hydraulic pump cavitation.

Prevent tank collapse at altitude.

Two types of hydraulic fluids currently being used in civil aircraft are

Mineral base, and phosphate ester base.

Mixed mineral base and phosphate ester base.

Petroleum base and mixed mineral base.

Which of the following lists only desirable properties of a good hydraulic fluid that has chemical stability?

Low viscosity, high flash point, high fire point.

High viscosity, low flash point, high fire point.

High flash point, low viscosity, low fire point.

Characteristics of MIL-H-8446 (Skydrol 500 A & B) hydraulic fluid are

light purple color, phosphate ester base, fire resistant, butyl rubber seals.

blue color, phosphate ester base, fire resistant, butyl rubber seals.

light green color, phosphate ester base, fire resistant, butyl rubber seals.

In brake service work, the term “bleeding brake” is the process of.

withdrawing fluid from the system for the purpose of removing air that has entered the system

replacing small amounts of fluid in reservoir.

withdrawing air only from the system.

What should be check when a shock strut bottoms during a landing?

Packing seals for correct installation.

Excluding line, which components are required to make up a simple hydraulic system?

Pump, reservoir, selector valve, and actuator.

Pump, reservoir, relief valve, and shuttle valve.

Actuator, pressure reservoir, accumulator, and selector valve.

Aircraft fuel and flight control systems worksheet

Authored by YoShiko Deten!

Professional Development

Used 45+ times

Aircraft fuel and flight control systems worksheet

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

112 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A fuel cross-feed valve is usually in

A. the closed position.

B. the open position.

C. its last position.

D. on position.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

The primary purpose of an aircraft's fuel jettison system is to quickly achieve a:

A. lower landing weight.

B. balanced fuel load.

C. reduced fire hazard.

D. all of above.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Integral tanks are.

A. cavities within the aircraft's airframe itself.

B. external tanks needs to be fabricated.

C. external tanks required to put in the airframe.

D. there is no such type of fuel tank.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

When refueling.

A. the fuel nozzle will automatically cut off the supply when the tank is full.

B. the fuel nozzle will manually cut off by pilot.

C. it is important to fill the expansion space in the tank.

D. it is important not to fill the expansion space in the tank.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Microbial growth is.

A. red dots

B. brown black slime

C. green sludge

D. yellow dots

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

A zero fuel test on a fuel quantity indicating system is carried out with.

A. tanks completely full.

B. tanks with unusable fuel.

C. tanks empty apart from unusable fuel.

D. tanks completely empty.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

On large transport aircraft fuel is delivered to each engine using

A. a parallel system.

B. a series system.

C. a separate system for each engine.

D. the same system for each engine.

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Popular Resources on Wayground

10 questions

Fire Safety Quiz

Quiz

•

12th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

20 questions

Inferences

Quiz

•

4th Grade

36 questions

6th Grade Math STAAR Review

Quiz

•

6th Grade

19 questions

Classifying Quadrilaterals

Quiz

•

3rd Grade

12 questions

What makes Nebraska's government unique?

Quiz

•

4th - 5th Grade

Discover more resources for Professional Development

17 questions

Filling out Forms

Quiz

•

Professional Development

Aircraft fuel and flight control systems worksheet

A fuel cross-feed valve is usually in

The primary purpose of an aircraft's fuel jettison system is to quickly achieve a:

Integral tanks are.

When refueling.

Microbial growth is.

A zero fuel test on a fuel quantity indicating system is carried out with.

On large transport aircraft fuel is delivered to each engine using

In biologically contaminated fuel, corrosion takes place.

Cross feed valves permit fuel transfer from.

The purpose of a scavenge system within a fuel system is.

Access all questions and much more by creating a free account

Popular Resources on Wayground

Discover more resources for Professional Development