NEW
Font size
S
M
L
XL
WorksheetsUnit 113 Hand tools
Total questions: 31
Worksheet time: 8mins
Name
Class
Date
1.
Which chisel is the most flexible?
a)
Gouge
b)
Pairing
c)
Firmer
d)
Bevel
2.
What plane is this ?
a)
Boat plane
b)
Curved plane
c)
Compass plane
d)
spoke shave
3.
What blade is this ?
a)
Crosscut
b)
Rip
c)
Tenon
d)
I don't know
4.
A Tenon saw is a type of what saw?
a)
Back
b)
Shoulder
c)
Joint
d)
Bench
5.
What is the bottom of the plane called?
a)
Back
b)
Bottom
c)
Base
d)
Sole
6.
What is the part of the chisel that sits inside the handle ?
a)
shaft
b)
tang
c)
Ferrell
d)
handle
7.
What is the grinding angle for chisels?
a)
25 degrees
b)
30 degrees
c)
20 degrees
d)
35 degrees
8.
What does TPI stand for?
a)
Threads per inch
b)
Teeth per inch
c)
Tooth piece increase
d)
Tuned port injection
9.
What is the space between the teeth called?
a)
space
b)
kerf
c)
Gullet
d)
Gap
10.
What plane is this?
a)
Convex
b)
Round
c)
Orbit
d)
Compass
11.
Name this screwdriver bit?
a)
Phillips
b)
Positive
c)
Pozi
d)
Peter
12.
What stone is used for Gouge chisels?
a)
Oil stone
b)
Dimond stone
c)
Coarse stone
d)
Slip stone
13.
What is the Honing angle for chisels?
a)
30 degrees
b)
25 degrees
c)
35 degrees
d)
20 degrees
14.
Name this chisel?
a)
Pairing
b)
Firmer
c)
Parting
d)
Bevel edge
15.
Which plane is the longest?
a)
Jack
b)
smoothing
c)
Block
d)
Trying
16.
Which Hammer do you strike a chisel with?
a)
Claw hammer
b)
Lump hammer
c)
Mallet
d)
Pein hammer
17.
How many teeth per inch on a Dovetail saw?
a)
8-10
b)
6-8
c)
16-22
d)
12-14
18.
Which is the third stage of setting and sharpening a saw?
a)
Sharpening
b)
Shaping
c)
Topping
d)
Setting
19.
On what surface would you use these drill bits?
a)
Masonary
b)
Timber
c)
Plasterboard
d)
Tiles
20.
Name this Holding device?
a)
G clamp
b)
Sash clamp
c)
F clamp
d)
Frame clamp
21.
Which drill hole is smaller?
a)
Clearance
b)
Pilot
c)
Spade
d)
Auger
22.
When Honing a chisel or plane blade which direction do you move it?
a)
Figure of 8
b)
Left to Right
c)
Forward and Bacwards
d)
Criss
23.
Which chisel is best to use on Dovetails?
a)
Mortice
b)
Firmer
c)
Bevel edged
d)
Gouge
24.
Block planes are used for what?
a)
Redressing timber
b)
Smoothing
c)
Dressing joints
d)
Cutting end grain
25.
This saw is a?
a)
Masonary saw
b)
Dovetail saw
c)
Tenon saw
d)
Floorboard saw
26.
Which Legislation covers the use of hand tools?
a)
COSHH
b)
PPE
c)
PUWER
d)
WAHR
27.
What is the name of the cut that the saw makes?
a)
Crosscut
b)
Curfew
c)
Kerf
d)
Rip
28.
Which pencil grade is the most recommended for use in carpentry?
a)
HB
b)
B
c)
2H
d)
3B
29.
What is the Bullnose plane used for?
a)
Noseings
b)
Clearing out corners
c)
Hinges
d)
Dovetails
30.
What gauge is this?
a)
Cutting
b)
Marking
c)
Mortice
d)
Wooden
31.
Name the part labelled at C
a)
Top iron
b)
Guard
c)
Lever cap
d)
Backing iron
Reset
