NEW
Font size
S
M
L
XL
WorksheetsTools of the Trade
Total questions: 20
Worksheet time: 10mins
Name
Class
Date
1.
Identify this hand tool. Also known as Channel locks.
a)
tongue & groove
b)
pliers
c)
pipe wrench
d)
slip joint pliers
2.
What name does NOT identify this hand tool.
a)
Lineman's pliers
b)
Side cutters
c)
Electrician's pliers
d)
Diagonal cutting pliers
3.
Identify this hand tool.
a)
diagonal cutting pliers
b)
side cutters
c)
needle nose pliers
d)
channel locks
4.
Identify this hand tool.
a)
nut driver
b)
reamer
c)
socket tool
d)
burr remover tool
5.
Which saw is NOT used to cut sheet rock?
a)
Sheetrock saw
b)
Keyhole saw
c)
Drywall saw
d)
Hand saw
6.
Identify this tool
a)
Socket drivers
b)
Nut drivers
c)
Screwdrivers
d)
Bolt drivers
7.
Identify this tool.
a)
Ratchet cable cutters
b)
Loppers
c)
Hand cable cutters
d)
Sidecutters
8.
The ________________ are similar to common scissors and is used for cutting sheet metal or metal studs.
a)
Hand scissors
b)
Cutters
c)
Tin snips
d)
Shears
9.
The ____________________ is used to remove the outer metal casing of MC or armored cable
a)
Roto splitter
b)
Roto stepper
c)
Roto spitter
d)
Cable splitter
10.
A _____________________is a tool for marking long, straight lines on relatively flat surfaces, much farther than is practical by hand or with a straightedge.
a)
Plumb bob
b)
Chalk line
c)
Chalk string
d)
Plumb tool
11.
The _____________________ can be used to drive in stakes and ground rods.
a)
Hammer
b)
Sledgehammer
c)
Mallet
d)
Ball-peen hammer
12.
When transferring a measurement from the ceiling to floor a _______________ is used.
a)
Chalk line
b)
Sponge bob
c)
Plumb bob
d)
Weight bob
13.
When an object is plumb, it is ________________.
a)
perfectly horizontal
b)
straight
c)
perfectly vertical
d)
flat
14.
The __________________ is used to check if a surface or object (like a piece of pipe) is level and/or plumb.
a)
torpedo level
b)
chalk line
c)
plumb bob
d)
combination square
15.
What type of hammer is shown?
a)
ball-peen
b)
claw
c)
sledge
d)
Electrician's hammer
16.
Identify this tool also known as long nose pliers used to grab things in tight places.
a)
slip joint pliers
b)
diagonal cutting pliers
c)
needle nose pliers
d)
channel locks
17.
A length of thin flexible metal, marked off in units (such as inches or centimeters) for measuring.
a)
Chalk line
b)
Tape measure
c)
Ruler
d)
Scale
18.
Used to remove insulation of larger size cables.
a)
box cutter
b)
razor knife
c)
scissors
d)
unity knife
19.
Is designed to cut through metal and cuts on the push stroke rather than the back stroke.
a)
hand saw
b)
band saw
c)
sawzall
d)
hacksaw
20.
This tool can replace several sizes of screwdrivers whether phillips or slotted, square, torx or nut drivers.
a)
10 in 1
b)
combination screwdriver
c)
Phillips head screwdriver
d)
Slotted screwdriver
Reset
