NEW
Font size
S
M
L
XL
WorksheetsExcavator and Bulldozer ID Test
Total questions: 22
Worksheet time: 40mins
Name
Class
Date
1.
This is an example of a track ____________ .
a)
Floater
b)
Pad
c)
Mat
d)
Plate
2.
This component circled in the picture would be called a ________ _________ .
a)
Bottom roller
b)
Track wheel
c)
Carrier roller
d)
Drive wheel
3.
The purple arrow in the picture is pointing to the front _____________________ .
a)
Idler
b)
Boggy wheel
c)
Pivot wheel
d)
Roller
4.
The arrow in this photo is pointing to the _____________________ .
a)
ROPs
b)
Sweeps
c)
Supports
d)
Channels
5.
The component on this hydraulic excavator that the green arrow is pointing to is called a ______________ .
a)
Grapple
b)
Shear
c)
Backing Pad
d)
Thumb
6.
The red arrow is pointing to what of the following components ?
a)
Boom
b)
Jib
c)
Stick(arm)
d)
Extender
7.
The component circled in this picture is an example of a blade ______ _______ .
a)
End bit
b)
Cutting edge
c)
Corner cutter
d)
Ripper shank
8.
The cylinder circled in this photo would be called the __________________ cylinder .
a)
Boom
b)
Stick
Stick
Stick
c)
Bucket
d)
Outrigger
9.
This circled component in this picture would be referred to as a __________________ .
a)
Rear bumper
b)
Counterweight
c)
Component cover
d)
Sheet metal
10.
The arrow in this picture is pointing to the _________________ .
a)
Final Drive
b)
Speed Reducer
c)
Interaxle Differential
d)
Transmission
11.
This bucket in this photo would be considered a _____________ bucket .
a)
Ditching
b)
General purpose
c)
Clamshell
d)
4 in 1
12.
The component circled in this photo is referred to as a _____________ .
a)
Cable spool
b)
Drum spool
c)
Winch
d)
Cable guide
13.
The component circled in this photo is referred to as a __________________ .
a)
Pin holder
b)
Draw bar
c)
Rear A arm
d)
Anchor tie down
14.
The arrow in this photo of a dozer is pointing to the _______________ .
a)
FOPs
b)
Sun canopy
c)
Post uprights
d)
ROPs
15.
This type of bucket found on this excavator would be considered a ___________ bucket.
a)
General purpose
b)
Clam shell
c)
Ditching
d)
4 in 1
16.
The circled cylinder on this bulldozer would described as a blade ______________ cylinder.
a)
Angle
b)
Tilt
c)
Lift
d)
Boom
17.
The circled part of the blade in this photo that runs along the bottom of the blade and is bolted to the moleboard is referred to as the ___________________ .
a)
End bits
b)
Ice grouser
c)
Level plane
d)
Cutting edge
18.
This picture is an example of a ________________ .
a)
Broken sprocket
b)
Sprocket segment
c)
Tooth wear gauge
d)
Tooth shank
19.
The circled portion of this track pad represents a ________________ .
a)
Grouser
b)
Paddle
c)
Flap
d)
Digger
20.
This component is an example of a track _____________ .
a)
Sprocket
b)
Idler
c)
Rotary wheel
d)
Tooth wheel
21.
The control pattern shown in the picture would be called ___________________________ type controls.
a)
SAE (ISO)
b)
John Deere
c)
Caterpillar
d)
Terex
22.
The control pattern shown in the picture would be an example of what type of controls ?
a)
John Deere
b)
SAE (ISO)
c)
Caterpillar
d)
Terex
Reset
