NEW
Font size
S
M
L
XL
WorksheetsLV012 Revision
Total questions: 20
Worksheet time: 10mins
Name
Class
Date
1.
Name this Component?
a)
Clutch Cover
b)
Release Bearing
c)
Friction Plate
d)
Bell Housing
2.
Name this component?
a)
Flu Hat
b)
Cold Hat
c)
Cold Sore
d)
Australian Flu
3.
How would you diagnose a fault with this component?
a)
Road test on full lock, listen for knocking noise coming from wheel
b)
Just fit a new one
c)
Road test drive in straight line
d)
Road test , reverse car uphill
4.
What fault would occur if you had excessive clutch free play?
a)
Change gear perfectly
b)
Difficult to engage gears
c)
Jump out of gear
d)
No fulat this is correct
5.
What fault would occur if you had to much free play?
a)
Nothing
b)
Jump out of gear
c)
Crunch gears on selection
d)
Slip
6.
What is the cushioning spring called in the middle of a friction plate?
a)
Marcell
b)
Callum Morgan
c)
Fred
d)
Martini
7.
Name this Component?
a)
Flywheel
b)
Clutch Center plate
c)
Clutch assembly
d)
Clutch cover
8.
What component helps to keep the engine running on its non power stroke?
a)
Starter motor
b)
Ring Gear
c)
Clutch cover
d)
Flywheel
9.
What is the purpose of the springs in the center of this component?
a)
To make it look good
b)
To absorb shocks
c)
To lock the plate against the flywheel
d)
To transmit drive
10.
Which of the following is a common oil used in light vehicle manual gearbox?
a)
DOT 4
b)
10w 5
c)
EP 80
d)
TQ12
11.
Name this clutch operating system?
a)
Cable
b)
Water
c)
Hydraulic
d)
Air
12.
What is the purpose of this component?
a)
To connect the gear stick to the steering wheel
b)
Connect the gear stick to front wheels
c)
Connect the gear stick to the gearbox
d)
Handbrake cables
13.
What is the purpose of this component?
a)
To synchronize the road wheels to flywheel speed
b)
To synchronize the speed of the gears to allow smooth gear change
c)
To bulk the gear change
d)
To make the gearbox more expensive
14.
What is the purpose of the grooves on the inner part of a SYNCHRO ring?
a)
To cut into the taper on the gear
b)
To cut away the sawdust
c)
To cut away the film of oil to help slow the gear down
d)
To cut technicians fingers when new
15.
What is the purpose of a differential?
a)
To make both wheels spin in opposite directions
b)
To slow the outer wheel down when cornering
c)
To increase the speed of the outer wheel on cornering
d)
To prevent brakes locking up
16.
What is the primary function of this component?
a)
To prevent gears from jumping out of mesh
b)
To make it hard to move the selector
c)
To make the gears jump out their skin
d)
To make it hard to strip the gearbox
17.
What is the primary function of this component?
a)
To prevent selection of two gears
b)
To stop Callum moaning
c)
To keep Raymont quite
d)
Play a violin for Kirsten
18.
Name the primary purpose of playing this instrument?
a)
To help others understand the hardship we all have to endure
b)
Callums favorite instrument
19.
Name this component and the type of drive
a)
Propshaft front wheel drive
b)
Constant velocity joint rear wheel drive
c)
Propshaft rear wheel drive
d)
Constant velocity joint front wheel drive
20.
On a rear wheel drive vehicle why would we have either a sliding joint at the gearbox or in the middle of the propshaft?
a)
To allow for movement of the prop when the vehicle goes up and down over different terrain
b)
To make it more expensive
c)
No real advantage
d)
To allow the gearbox and rear diff to move in tandem
Reset
