wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

Fire Inspector

Total questions: 61

Worksheet time: 31mins

Name
Class
Date
1.

Which of the following is true concerning the tensile strength of steel?

a)

The tensile strength of steel is one-half of the compressive strength

b)

The tensile strength of steel is twice the compressive strength

c)

The tensile strength of steel is ten times the compressive strength

d)

The tensile strength of steel is equal to the compressive strength

2.

Which of the following best describes the tensile strength of concrete?

a)

Strong

b)

Moderate

c)

Weak

d)

There is no tensile strength in concrete

3.

What is the supported at only one end and is rigidly held in position at the end?

a)

Bar joist

b)

Cantilever beam

c)

lintel

d)

overhanging beam

4.

What is supported at three or more joints?

a)

Continuous beam

b)

Cantilever beam

c)

Fixed beam

d)

Simple beam

5.

The proper way to breach a masonry wall is to open which of the following shaped holes?

a)

Square

b)

Circular

c)

Triangular

d)

Rectangular

6.

What is lumber that is eight inches or more in its smallest dimension called?

a)

Plywood

b)

Heavy timber

c)

Rough timber

d)

Timber

7.

Often wood chips are glued together to make flat sheets. ______is/are sometimes used for flooring of mobile homes. They are water-soluble and may dissolved in fires.

a)

Planks

b)

Finger joints

c)

Laminated timbers

d)

Chipboard

8.

Failure of a gusset plate will cause tensile loads to do which of the following?

a)

It will cause them to shift

b)

It will pull apart the truss

c)

It will remain the same as gusset plates have no bearing on tensile loads.

d)

It will cause them to stretch

9.

What is the covering that is applied directly to the studs or framing of the structure?

a)

Finish

b)

Sheathing

c)

Siding

d)

Veneer

10.

Bricks laid so that the long side is visible compose which of the following?

a)

A header

b)

A bond course

c)

A stretcher course

d)

A solid masonry wall

11.

Stone cut in rectangular units.

a)

Adobe

b)

Ashlar

c)

Terra cotta

d)

Parging

12.

Structural steel will fail at approxiamately which of the following temperatures?

a)

800 degrees Fahrenheit

b)

1000 degrees Fahrenheit

c)

1500 degrees Fahrenheit

d)

2000 degrees Fahrenheit

13.

Two stairways are frequently found in the same shaft. If there is a standpipe, the outlets will be alternative stairways, floor by floor. These stairways are known as ____stairways.

a)

Fire tower

b)

Smoke shaft

c)

Intermediate vestibule

d)

Scissor

14.

What is the fire resistance of floors and walls concerned with?

a)

Resisting collapse

b)

Resisting the passage of fire

c)

Resisting smoke movemenet

d)

Resisting the passage of fire and collapse

15.

What describes a passageway, usually vertical, that is cut into a masonry wall for a pipe or conduit?

a)

Course

b)

Cavity

c)

Header

d)

Chase

16.

What is the weight of a building and any equipment permanently attached to it or built in the building called?

a)

Live load

b)

Impact load

c)

Concentrated load

d)

Dead load

17.

A very heavy load located at one point in a building is known as which of the following?

a)

An eccentric load

b)

A live load

c)

A torsional load

d)

A concentrated load

18.

What is a measure of the ability of a material to yield and return to its original shape?

a)

Moment of inertia

b)

Shear

c)

Buckle

d)

Modules of elasticity

19.

Which of the following is any beam, of any material, that supports other beams?

a)

Joist

b)

Needle Beam

c)

Grillage

d)

Girder

20.

A material that returns to its original shape after a load is removed is said to be within its ______ range?

a)

plastic

b)

elastic

c)

target

d)

design

21.

A material that is permanently deformed after the load is removed is said to have exceeded its _________ range.

a)

plastic

b)

elastic

c)

target

d)

design

22.

What is the top membr of the truss called?

a)

A web

b)

A pratt

c)

A strut

d)

A chord

23.

What is the bottom member of a truss known as?

a)

A chord

b)

A web

c)

A tie

d)

A pratt

24.

To benfit from the most support, wood beams are placed....

a)

On top of girders

b)

In-line with the girders

c)

Below the girders

d)

connected into the girders

25.

Loads that are delivered in a short time are termed as which of the following?

a)

Traumatic loads

b)

Impact loads

c)

Dead loads

d)

Shock loads

26.

Which of the following describes a beam that spans an opening in a masonry wall?

a)

Lintel

b)

Spandrel

c)

Cantilever

d)

Grillage

27.

The process of covering a masonry wall with a thin coat of concrete is known as which of the following?

a)

Veneering

b)

Parging

c)

Facing

d)

Finishing

28.

A bearing wall common to two structures. If structural members of both buildings are located in common sockets, fire can extend through the opening. This is a problem area of a _____ wall.

a)

Fire

b)

Barrier

c)

Wing

d)

Party

29.

Which of the following beams would support its load longer while burning?

a)

2-inch by 10-inch wooden beam

b)

4-inch by 10-inch wooden beam

c)

1-inch by 8-inch wooden beam

d)

3-inch by 10 inch wooden beam

30.

What is a vertical section of a wall, one brick or masonry unit thick called?

a)

Wythe

b)

Bond course

c)

Column

d)

Cavity wall

31.

Veneer walls, curtain walls and partition walls are example of what type of walls?

a)

Fire-rated

b)

Self-sustaining

c)

Non-load bearing

d)

Panel

32.

What is used to limit the movement of fire through relatively small concealed passages such as under stairs and inside walls?

a)

Draft stops

b)

Insulations

c)

Fire stops

d)

Firebreaks

33.

The main common characteristic of ordinary construction is that the exterior walls are made of which of the following?

a)

Wood

b)

Masonry

c)

Cast-iron

d)

Concrete

34.

Cutting the end of a beam at an angle so that the beam can fall out of the wall during a fire is called which of the following?

a)

Fire cutting

b)

Shaping

c)

Compartmentalization

d)

Chasing

35.

What term is used to describe the loss of surface material when concrete is subjected to heat?

a)

Spalling

b)

Casting

c)

Flaking

d)

Shedding

36.

Row houses, town houses, and condominiums are examples of:

a)

Ordinary construction

b)

Wood construction

c)

Steel construction

d)

Garden apartments

37.

What is a method of construction known as where all of the concrete in a building is properly bonded together to be like one piece of stone?

a)

Pre-cast construction

b)

Slip forming construction

c)

Monolithic construction

d)

Composite construction

38.

What are the two prestressing methods used with concrete construction?

a)

Pretensioning and post-stressing

b)

Precast and post-cast tensioning

c)

Pretensioning and post-tensioning

d)

Prestrung and post indicating tension

39.

*NFPA 20 requires that an ______ flow test of the pump assembly be performed to determine its ability to continue to attain satisfactorily performance at shutoff, rated flow, and peak poads. It also requires that pumps designed to turn on in response to drops in water pressure shall be started _____.

a)

monthly, daily

b)

annual, daily

c)

*annual, weekly

d)

annual, monthly

40.

What is the temporary structure called that is erected to support concrete work in the course of construction?

a)

Falsework

b)

Shoring

c)

Formwork

d)

Sluffing

41.

A heated steel beam that is not past the point of strain (elastic range) will do which of the following when cooled with streams of water?

a)

It will buckle

b)

It will return to its original shape

c)

It will elongate

d)

It will keep its deformed shape

42.

A heated beam that is past the point of strain (plastic range) will do which of the following when cooled with streams of water?

a)

It will buckle

b)

It will return to its original shape

c)

It will elongate

d)

It will keep its deformed shape

43.

What represents the potential fuel available to a fire?

a)

Fuel load

b)

Fire load

c)

Fire resistance

d)

Design load

44.

Precast beams often have the word "____" cast in the top of the beam because the reinforcing rods are in the top of the beam.

a)

Precast

b)

P/C

c)

Top

d)

Reinforced

45.

There are two types of concrete construction. They are:

a)

Precast and cast-in-place

b)

Pretension and post tensioned

c)

Precast and post cast

d)

Post cast and pre-stressed

46.

Which of the following statements is incorrect?

a)

Reinforcing bars serve not only to create a composite material but also to carry some of the compressive load.

b)

Protruding bars are a serious sign of possible collapse and should bring about the immediate evacuation of the area

c)

Pre-stressing places engineered stresses in architectural and structural concrete to offset the stresses that occur in the concrete when it is placed under load

d)

Concrete is strong in tension strength with high shear resistance

47.

A common truss used for steep roofs would be a:

a)

Parallel Chord truss

b)

Inverted Queen post truss

c)

Inverted King Post truss

d)

Scissors truss

48.

Which of the following is represented by the ratio of the strength of the material just before failure, to the safe working stress?

a)

Tolerance

b)

Variance

c)

Ultimate stress

d)

Safety factor

49.

What are steel pipes called that are filled with concrete in order to increase their load-carrying capacity?

a)

Aggregates

b)

Lally columns

c)

Reinforcing bars

d)

Mushroom caps

50.

What is the covering that is applied directly to the studs or framing of the structure?

a)

Finish

b)

Sheathing

c)

Siding

d)

Veneer

51.

What type of force is perpendicular to the plane of the section under consideration but does not pass through the center of the section?

a)

A shear load

b)

A torsional load

c)

An eccentric load

d)

An axial load

52.

Structural steel will fail at approxiamately which of the following temperatures

a)

800 degrees Fahrenheit

b)

1000 degrees Fahrenheit

c)

1500 degrees Fahreneheit

d)

2000 degrees Fahrenheit

53.

Aircraft hangers are usually built of unprotected steel and are equipped with ____ sprinklers systems.

a)

wet pipe

b)

dry pipe

c)

pre-action

d)

deluge

54.

Sprinkler heads rated for the Ultra High temperatures classification are color coded:

a)

yellow

b)

white

c)

blue

d)

orange

55.

Which of the following sprinkler system components is used to limit water flow to one direction?

a)

OS&Y valve

b)

Check valve

c)

Control valve

d)

Butterfly valve

56.

Which of the following should be used by fire inspectors that will allow them to function within the normally-accepted legal guidelines?

a)

Inspectors should request a search warrant if entry for a code compliance inspection is denied

b)

Fire inspectors should invite a representative of the building/occupancy to walk alond during the inspection

c)

Fire inspectors must request permission from the property owner/occupant to conduct an inspection

d)

All of the above

57.

Which National Fire Protection Association (NFPA) standard provides the minimum design and installation requirements of sprinkler systems found in most buildings?

a)

NFPA 1001

b)

NFPA 30-A

c)

NFPA 30

d)

NFPA 13

58.

The pressure above the clapper valve in a wet pipe will be _____ than the pressure below the clapper valve.

a)

higher

b)

equal to

c)

lower

d)

both higher and equal to

59.

On a wet-pipe sprinkler system with an alarm check valve, the _____ is _____ to test the alarm without unseating the alarm check valve

a)

alarm test valve, opened

b)

2-inch drain open

c)

main control valve, opened

d)

Inspector's test connection, open

60.

How often should the alarms of the sprinkler system be tested?

a)

Annually

b)

Semiannually

c)

Quarterly

d)

Monthly

61.

How often should wet pipe system alarms be tested

a)

Daily

b)

Quartly

c)

Monthly

d)

Weekly