Free Printable Table saws unit 211

1.

What does PUWER is stand for?

a)

Provision and Use of Work Equipment Requirements

b)

Provision and Use of Work Equipment Regulations

c)

Provision and Use of Work Equipment Restrictions

d)

Prolonging and Use of Work Equipment Regulations

2.

he extension table fitted at the back of a circular saw must not be positioned:

a)

Less than 1200mm from the centre of the saw

blade

b)

Less than 1200mm from the riving knife

c)

Less than 1200mm from the saw teeth

d)

Less than 1200mm from the operator

3.

What type of tooth pattern should a crosscut saw

have?

a)

Positive hook

b)

Negative hook

c)

Positive pitch

d)

Negative pitch

4.

What does TCT stand for?

a)

Technically crafted tip

b)

Tungsten carbide tip

c)

Tungsten carbon tip

d)

Tensile carbon tip

5.

What should be the minimum length of a push

stick?

a)

400mm

b)

425mm

c)

350mm

d)

450mm

6.

What are positive tooth pattern saw blades

suitable for?

a)

Cutting along the grain

b)

Cutting deep cuts

c)

Cutting hardwoods

d)

Cutting across the grain

7.

A saddle uses on a circular rip saw bench will

assist with:

a)

Deep cuts

b)

Angled cuts

c)

Using negative tooth pattern saws blades

d)

Using positive tooth pattern saw blades

8.

What should you do if you find a circular saw

bench with a missing guard?

a)

Use the machine as long as long as you have told

your employer

b)

Use the machine as long as you have been trained

c)

Not use the machine and report to your employer

straightaway

d)

Not use the machine and carry on with another

job

9.

What is the most efficient form of dust collection

within a joiner’s workshop?

a)

Fixed ducted system

b)

Portable vacuum with hose

c)

Dust bag attached to machine

d)

Sweep up at end of job

10.

The riving on a circular saw bench can act as a

form of:

a)

Safety switch

b)

Guard

c)

Support for the timber

d)

Guide for the timber

11.

What is the minimum size of saw blade allowed

compared to the largest?

a)

40%

b)

50%

c)

30%

d)

60%

12.

What type of saw blade is best for ripping hard abrasive

timber such as oak?

a)

Negative tooth pattern with TCT teeth

b)

Positive tooth pattern with TCT teeth Negative tooth pattern with TCT teeth

c)

Negative tooth pattern with mild steel teeth

d)

Positive tooth pattern with mild steel teeth

13.

Cutting hard abrasive timber will:

a)

Prevent accurate cutting

b)

Dull the cutting edge more quickly

c)

Require the use of a push stick

d)

Prevent the need of cleaning the saw blade

14.

What is the total width of the saw cut called?

a)

Set

b)

Pitch

c)

Gauge

d)

Kerf

15.

The riving knife on a circular rip saw bench will help:

a)

Prevent binding

b)

Cause binding

c)

With extraction

d)

Hold the saw blade

16.

What is the most efficient method of timber

conversion?

a)

Through and through

b)

Quarter sawn

c)

Box heart

d)

Radial sawn

17.

For saw blades of less than 600mm diameter the riving knife should be

a)

Within 50mm of the top of the saw blade

b)

Within 50mm of the top of the saw bench

c)

Within 25mm of the top of the saw blade

d)

Within 225 from the saw bench

Table saws unit 211

Total questions: 17

Worksheet time: 5mins

Similar Resources on Wayground