wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

AAD EOC (1 of 2)

Total questions: 171

Worksheet time: 1hrs 26mins

Name
Class
Date
1.

What is a term used in building codes to describe access?

a)

Exit

b)

Stair wells

c)

IRC code book

d)

Egress

2.

Outlets should average one for every ___ feet of wall space.

a)

5'

b)

12'

c)

4'

d)

6'

3.

Choose the correct door swing.

a)

A

b)

B

c)

All of the options

d)

None of the options

4.

What is the minimum clearance distance in front of a sink?

a)

19"

b)

21"

c)

22"

d)

24"

5.

In residential construction, what is the minimum width of a half bath?

a)

30"

b)

32"

c)

34"

d)

36"

6.

What is the correct symbol for a Hose Bib in the image shown?

a)

A

b)

B

c)

C

d)

D

7.

What is the correct symbol for a standard 110v/115v outlet in the image shown?

a)

A

b)

B

c)

C

d)

D

8.

1/4"=1'-0" and 1:48 scale are the same.

a)

True

b)

False

9.

The soil stack is a vertical soil pipe carrying the discharge from the toilet fixture.

a)

True

b)

False

10.

When showing stairs on a floor plan you should always show and arrow going up but not going down.

a)

True

b)

False

11.

A hearth should always have a finish elevation of 0'-0".

a)

True

b)

False

12.

The ADA codes are always used in residential drawings.

a)

True

b)

False

13.

Doorknobs on doors can be operated more easily than levers.

a)

True

b)

False

14.

GFCI outlets should be installed near any water source.

a)

True

b)

False

15.

All outside outlets do not need to be weatherproof outlets.

a)

True

b)

False

16.

Floor plans should only be drawn at 1/4"=1'-0".

a)

True

b)

False

17.

Solid concrete or block walls are dimensioned the same as wood construction. (10-34)

a)

True

b)

False

18.

Sub-dimensions must add up to overall dimensions.

a)

True

b)

False

19.

Heating and cooling equipment located in a garage must be protected from impact. This is generally done by placing what in front of the equipment?

a)

Mesh wire

b)

Cyclone fencing

c)

Steel pipe

d)

Wood fencing

20.

The minimum size door required to access HVAC equipment is:

a)

42"

b)

36"

c)

22"

d)

20"

21.

Suspended HVAC equipment must be at least ____ from the ground.

a)

6"

b)

8"

c)

10"

d)

None of the options.

22.

Factory-made ducts must be approved and labeled by:

a)

LU

b)

UL

c)

IRC

d)

RAC

23.

When ducts must be run between floors, they need to be run in a(n):

a)

Open space

b)

Insulated space

c)

Concealed space

d)

Outside

24.

If a residential or commercial structure cannot be uniformly heated or cooled from one compressor a ____system may be required.

a)

double

b)

series

c)

split

d)

parallel

25.

One type of zonal heater is:

a)

Radiator

b)

Blower

c)

Baseboard

d)

None of the options

26.

In a central heating system, the thermostat should be placed:

a)

By a door

b)

In the kitchen

c)

Close to a return air duct

d)

Near a window

27.

A fitting with a removable plug is a:

a)

Drain

b)

Fitting

c)

Cleanout

d)

Main

28.

A pipe, normally underground, that carries wastewater and refuse is a :

a)

Soil pipe

b)

Stack

c)

Sewer

d)

Trap

29.

A pipe that carries the discharge of water closets or other similar fixtures is a:

a)

Sewer

b)

Soil pipe

c)

Stack

d)

Trap

30.

Locating the water heater in an insulated space is one example of:

a)

Poor design

b)

Energy conservation

c)

Unnecessary

d)

None of the options

31.

Another name for a water closet is:

a)

Bide

b)

Toilet

c)

Unnecessary

d)

None of the options

32.

Plumbing riser diagrams are usually drawn as an:

a)

Oblique

b)

Isometric

c)

Orthographic

d)

Prospective

33.

When indicating pipe elevation, the abbreviation "BOP" stands for:

a)

Bottom of plumbing

b)

Bottom of pipe

c)

Big outside pipe

d)

Beginning

34.

Electrical installation for new construction occurs in what phases?

a)

Finish

b)

Rough-in

c)

Temporary

d)

All the options

35.

A conduit is:

a)

Pipe or tube to enclose electrical conductors

b)

Person on a train

c)

Outlet box

d)

Panel

36.

Maximum distance between wall plug is:

a)

6'

b)

12'

c)

13'

d)

15'

37.

Each wall over ___ must have an outlet.

a)

2'

b)

3'

c)

4'

d)

5'

38.

Keeping outlets to a minimum at exterior walls is considered:

a)

Energy conservation

b)

Poor design

c)

Unnecessary

d)

None of the options

39.

Identify the HVAC symbol.

a)

Turning vane

b)

Corner cut

c)

90 turn

d)

None of the options

40.

Identify the symbol.

a)

Double elbow

b)

Double branched flanged elbow

c)

Y-elbow

d)

Lateral

41.

Identify the symbol.

a)

Floor outlet single

b)

Floor switch

c)

Junction box

d)

Generator

42.

Identify the symbol.

a)

Flood light

b)

Fluorescent light

c)

Yard light

d)

Can ceiling light

43.

Identify the symbol.

a)

Radio outlet

b)

Phone

c)

Vacuum

d)

Transformer

44.

Some principle parts of a refrigeration system are:

a)

Cooling coil

b)

Compressor

c)

Expansion valve

d)

All of the options

45.

The code that controls electrical circuits and plans is the:

a)

NEC

b)

NIC

c)

CIC

d)

CAB

46.

Light switches would normally be placed ___ above the floor.

a)

2'-10"

b)

3'-0"

c)

3'-4"

d)

3'-6"

47.

Identify the HVAC symbol.

a)

Supply

b)

Diffuser

c)

Return

d)

Louver opening

48.

Identify the HVAC symbol.

a)

Airline valve

b)

Solenoid valve

c)

Relief valve

d)

Automatic 3-way valve

49.

Identify the HVAC symbol.

a)

Solenoid valve

b)

Relief valve

c)

Airline valve

d)

3-way valve

50.

Identify the symbol.

a)

Elbow up

b)

Lateral

c)

Union

d)

Elbow down

51.

Identify the symbol.

a)

Gate valve

b)

Globe valve

c)

Check valve

d)

Relief Valve

52.

Identify the symbol.

a)

Gate valve

b)

Globe valve

c)

Check valve

d)

Relief Valve

53.

Identify the symbol. (11-36)

a)

Floor switch

b)

Generator

c)

Junction box

d)

Floor outlet single

54.

Heating and cooling equipment do not need to be accessible.

a)

True

b)

False

55.

HVAC equipment located on the ground should be supported on a concrete slab.

a)

True

b)

False

56.

Equipment connected to duct systems must have a temperature limit control.

a)

True

b)

False

57.

HVAC equipment installed outdoors must be listed and labeled for outdoor use.

a)

True

b)

False

58.

Ducts in unconditioned areas do not have to be insulated.

a)

True

b)

False

59.

A heat pump is a forced-air central heating and cooling system.

a)

True

b)

False

60.

A zonal heating system allows the heating of the home to family's needs.

a)

True

b)

False

61.

A zonal heating system has only one thermostat for the house.

a)

True

b)

False

62.

A central heating system requires using all the heat produced.

a)

True

b)

False

63.

Industrial piping is used to carry liquids and gases used in the manufacture of products.

a)

True

b)

False

64.

Residential piping is called plumbing.

a)

True

b)

False

65.

Using a low-flow shower head is a good example of energy conservation.

a)

True

b)

False

66.

The only plumbing items shown on the floor plan are fixtures.

a)

True

b)

False

67.

There should be at least one ceiling outlet for every two cars in a garage.

a)

True

b)

False

68.

Smoke detectors are required in all bedrooms rooms.

a)

True

b)

False

69.

The description of the angle of the roof compared to the horizontal run and vertical rise is the:

a)

Angle

b)

Drop

c)

Run

d)

Slope

70.

The most common material for shingles is:

a)

Wood

b)

Fiberglass

c)

Asphalt

d)

All the options

71.

Fiberglass and asphalt shingles are commonly referred to as:

a)

Mixed Shingles

b)

Composition Shingles

c)

Combined Shingles

d)

None of the options

72.

What type of material is used for roofing in high fire areas?

a)

Tile

b)

Metal

c)

Tile and metal

d)

Ceramic

73.

What is shown on a roof framing plan?

a)

Connections to the foundation

b)

Rafters and other roof members

c)

Window and door locations

d)

None of the options

74.

A wall which supports its own weight and some other structural elements of the house such as

joists is called a:

a)

Strong wall

b)

Thick wall

c)

Bearing wall

d)

Non-bearing wall

75.

Identify the roof type.

a)

A-frame

b)

Hip

c)

Mansard

d)

Gable

76.

An opening framed in a roof to allow for window placement is called a:

a)

Domo

b)

Dormer

c)

Mansard

d)

Major domo

77.

On a roof framing plan, joists are drawn as:

a)

Hidden line

b)

Dashed line

c)

Thick line

d)

Thin line

78.

Identify the roof type.

a)

Hip

b)

Minaret

c)

Shed

d)

Gable

79.

Identify the roof type.

a)

Shed

b)

Gable

c)

Hip

d)

Arch

80.

Identify the roof type.

a)

Shed

b)

Gable

c)

Mansard

d)

Hip

81.

Identify the roof type.

a)

Gambrel

b)

Hip

c)

Arched

d)

Mansard

82.

Identify the roof style.

a)

Butterfly

b)

Mansard

c)

Hip

d)

Gable

83.

The basic shape of a roof corresponds with the design of the floor plan.

a)

True

b)

False

84.

A roof plan is used to show the shape of the roof.

a)

True

b)

False

85.

Complicated residential roofs usually require a roof framing plan.

a)

True

b)

False

86.

Roof pitch and slope mean the same thing. (12-18)

a)

True

b)

False

87.

Flat roofs are primarily used where there is a lot of rain.

a)

True

b)

False

88.

Gable roofs are the most common roof types in residential construction.

a)

True

b)

False

89.

A hip roof can create a structure with a smaller appearance.

a)

True

b)

False

90.

Wind resistance and seismic concerns can be considered when doing a roof framing plan.

a)

True

b)

False

91.

A roof framing plan shows the size and direction of the framing members.

a)

True

b)

False

92.

The roof framing plan would be drawn at the same scale as the floor plan.

a)

True

b)

False

93.

A hip roof slopes on only two sides.

a)

True

b)

False

94.

A nailing schedule is common with roof framing plans.

a)

True

b)

False

95.

A shed roof must be constructed at a 30º angle.

a)

True

b)

False

96.

A flat roof will often have a parapet wall surrounding the perimeter of the roof.

a)

True

b)

False

97.

Which of the following is not an elevation?

a)

Front

b)

Back

c)

Top

d)

Side

98.

Which of the following is not a basic type of information found on exterior elevation?

a)

Wall assemblies

b)

References

c)

Dimensional

d)

Structural

99.

The scale of exterior elevation is usually:

a)

As large as possible to fit on the drawing

b)

The same as the floor plan

c)

Selected to show the most detail

d)

1/4"=1'-0"

100.

The elevation which shows the most detail and clarity is generally the:

a)

Back

b)

Side

c)

Front

d)

Top

101.

How many elevations are typically required?

a)

1

b)

2

c)

3

d)

4

102.

What items would you normally show on exterior elevations?

a)

Windows, Doors, Siding, Brick

b)

Windows, Trees, Roof, Concrete

c)

Property lines, Roof, Utilities

d)

Windows, Doors, Plumbing fixtures

103.

Identify the item indicated by the arrow.

a)

Fascia

b)

Siding

c)

Foundation

d)

Wainscot

104.

Identify the item indicated by the arrow. (13-8)

a)

Topper

b)

Dormer

c)

Doghouse

d)

Shed

105.

The type of view shown in this image is called:

a)

Front and side elevation

b)

Angled View

c)

Perspective

d)

Elongated view

106.

In elevation, this symbol best describes what material?

a)

Standard Tabbed Shingles

b)

Architectural Shingles

c)

Rough Laid Shingles

d)

Structural Shingles

107.

Typical scale for drawing elevation is:

a)

1/16"=1'-0"

b)

1/8"=1'-0"

c)

1/4"=1'-0"

d)

1/2"=1'-0"

108.

When are additional elevations required on a building?

a)

When parts of the building are hidden

b)

When a building has more than one story

c)

When the building has a basement

d)

Never

109.

What information would you need to draw the elevations of a building?

a)

Floor Plan- Roof Plan- Wall Sections- Site Plan

b)

Floor Plan- Roof Plan- Plumbing- Schedules

c)

Floor Plan- Elevations- Wall Sections- Schedules

d)

Floor Plan- Roof Plan- Wall Sections- Schedules

110.

When making an elevation for a presentation what would be recommended?

a)

Show Notations

b)

Show in color

c)

Draw partial views

d)

Draw very large

111.

Skylights drawn on a front elevation would appear to be:

a)

Circular

b)

Oblique

c)

Elliptical

d)

Fat Bold Lines

112.

Knowing the direction of North on the Floor Plan, how would you label the elevations?

a)

Never Label

b)

Direction- North, South, East, West

c)

Use only the Front & Right Side Label

d)

By the Drawing- Front, Rear, Right and Left Side

113.

In elevation, the symbol shown best describes what material?

a)

Stucco

b)

Ceramic Tile

c)

Concrete Masonry Unit

d)

Drywall

114.

Elevation layout will depend on:

a)

Number of elevations required

b)

Sheet size

c)

Drawing scale

d)

All the options

115.

On an architectural elevation, one would not see a schedule for:

a)

Room Finishes

b)

Doors

c)

Roofing Materials

d)

Windows

116.

Identify the item indicated by the arrow.

a)

Side Trim

b)

Shutter

c)

Sash

d)

Storm Sash

117.

Identify the best description for the item indicated by the arrow.

a)

Stiff Leg

b)

Column

c)

Post

d)

Support

118.

If the Floor plans are drawn at 1/4"=1'-0," what would be the scale of the Elevations?

a)

1/4"=1'-0"

b)

1/2"=1'=0"

c)

3/4"=1'-0"

d)

1.1/2"=3'-0"

119.

Elevations can be either presentation drawings or working drawings.

a)

True

b)

False

120.

Elevations are necessary in calculating heat loss.

a)

True

b)

False

121.

Pitch or slope of the roof will determine if sky lights are drawn on elevations. (13-25)

a)

True

b)

False

122.

Which of the following is not a type of wood frame construction?

a)

Balloon

b)

Tongue and groove

c)

Post and beam

d)

Platform

123.

What is a major difference between balloon framing and platform framing?

a)

Balloon-framed studs end at the top plate of each floor level.

b)

Balloon-framed walls are always shorter than platform framed walls.

c)

Balloon-framed joists rest directly on the foundation wall.

d)

Balloon-framed studs start on the sill and continue uninterrupted to the top plate.

124.

In platform framing, the covering over the floor joists is:

a)

Floor covering

b)

Plywood

c)

Floor sheathing

d)

Plastic

125.

A beam is unsupported for a certain distance between posts; this distance is the _____ ?

a)

Reach

b)

Length

c)

Span

d)

Girder

126.

The most common interior wall covering is:

a)

OSB

b)

Gypsum board

c)

Plywood

d)

Foam board

127.

In residential construction, a veneer is:

a)

A non-structural covering material

b)

Thin material

c)

Shown as thin lines

d)

None of the options

128.

A sill plate usually rests on concrete or masonry; therefore it is:

a)

Foam board

b)

Painted

c)

Glued to the masonry or concrete wall

d)

Pressure-treated

129.

The lower vertical end of a rafter of truss is covered by the:

a)

Ridge board

b)

Soffit

c)

Frieze board

d)

Fascia

130.

The sill is secured to the foundation by:

a)

Frieze board

b)

Anchor bolts

c)

Soffit

d)

Ridge board

131.

The purpose of the wood sill in a framed structure is to:

a)

Provide a nailing surface

b)

Strengthen the foundation

c)

Serve as a spacer for the joist

d)

Straighten the wall aligned

132.

A truss gains its strength from ____ formed throughout it.

a)

Squares

b)

Triangles

c)

Circles

d)

Hexagons

133.

When a floor joist extends past it's support, the extension is known as a :

a)

Floor extension

b)

Cantilever

c)

Joist extension

d)

Poor floor design

134.

A bearing wall supports:

a)

Finish Floor

b)

Plywood

c)

Blocking

d)

All of the options

135.

Identify "BB."

a)

Plywood

b)

Blocking

c)

Sub Floor

d)

Finish Floor

136.

Identify "DD." (14-15)

a)

Post

b)

Studs

c)

Corner

d)

Lash Post

137.

Identify "EE."

a)

Header

b)

Beam

c)

Top Plate

d)

Sole Plate

138.

Identify "BB."

a)

Header

b)

Runner

c)

Top Beam

d)

Beam

139.

Identify "HH."

a)

Base Plate

b)

Sole Plate

c)

Runner

d)

Casing Plate

140.

Identify item "AA."

a)

Top plate

b)

Sill

c)

Header

d)

Stud

141.

Identify item "GG."

a)

Header

b)

Sill

c)

Stud

d)

Top plate

142.

Ceiling joists span between the top plates of bearing walls.

a)

True

b)

False

143.

A truss is usually prefabricated off site.

a)

True

b)

False

144.

"O.C" stands for "on center" and indicates the distance objects are apart, center to center.

a)

True

b)

False

145.

Gutters are most often attached to the soffit.

a)

True

b)

False

146.

A floor framing system doesn't require knowledge of loads and material strength.

a)

True

b)

False

147.

Platform framing is the most common framing system in use now.

a)

True

b)

False

148.

Knowing about balloon framing is not helpful when an old building is remodeled or renovated.

a)

True

b)

False

149.

A two-story structure is the maximum structure that can be built with balloon framing.

a)

True

b)

False

150.

Platform framing gets its name from a platform created on the foundation.

a)

True

b)

False

151.

Concrete Masonry Units (CMUs) provide excellent structural and insulation values.

a)

True

b)

False

152.

I - Joists are always made of steel or aluminum. (14-31)

a)

True

b)

False

153.

The main purpose of a foundation system is?

a)

Distribute the load of the building over the soil.

b)

To provide a solid, level base for wall construction.

c)

To allow even settlement of the building since all building settle to some degree.

d)

Dew point

154.

The maximum depth at which the ground may freeze is known as the:

a)

Freeze depth

b)

Ice line

c)

Frost line

d)

Dew point

155.

A sill plate usually rests on concrete or masonry; therefore it is:

a)

Foam board

b)

Glued to the masonry or concrete wall

c)

Painted

d)

Pressure-treated

156.

The most typical type of foundation used in residential construction is:

a)

Stem wall

b)

Piling

c)

Slab on grade

d)

Continuous or spread

157.

Control joints are used in concrete slabs for what reason?

a)

Control expansion

b)

Control sweating

c)

Control cracking

d)

None of the options

158.

Expansion joints are used in concrete slabs for what reason?

a)

Control cracking

b)

Control expansion

c)

Control Sweating

d)

None of the options

159.

The primary or most important ingredient in Concrete Mix is what?

a)

Cement

b)

Potash

c)

Sand

d)

Gravel

160.

What is the minimum thickness of concrete floor slabs allowed by code?

a)

2-1/2"

b)

3"

c)

3-1/2"

d)

4"

161.

Identify the type of foundation.

a)

Turn Down Foundation

b)

Slip Foundation

c)

Concrete

d)

Slab on Grade

162.

Crawl Space is defined as the:

a)

The area above the ceiling joist

b)

Area below the floor joist

c)

The area around the fire place

d)

The area underneath the stairs

163.

To meet building codes, every Footing is required to have:

a)

Drain pipe

b)

Waterproofing

c)

Insulation

d)

Reinforcing

164.

The one thing that every structure built is required to have is:

a)

Roof

b)

Foundation

c)

Walls

d)

Door

165.

Retaining walls are used to hold back:

a)

Wind

b)

Water

c)

Soil and rocks

d)

People

166.

A footing is used for the purpose of:

a)

Limiting building loads

b)

Spreading building loads

c)

Walking the concrete slab

d)

Creating building loads

167.

Concrete piers are used to:

a)

Support the walls

b)

Support the slab

c)

Tie up a boat

d)

Support interior loads

168.

The minimum footing thickness of a single story residential structure is normally never LESS than:

a)

4"

b)

6"

c)

8"

d)

10"

e)

12"

169.

What is the first step necessary when pouring a slab on grade?

a)

Purchase the concrete

b)

Remove all topsoil and grass

c)

Install the reinforcing

d)

Call a contractor

170.

In most areas, foundation slabs are required to have ___ installed under the slab.

a)

a polyethylene vapor barrier

b)

a plywood sheet

c)

pilings

d)

None of the options

171.

Identify the type of material indicated. (5-19)

a)

Brick

b)

Concrete

c)

Stone

d)

Masonry