Font size
WorksheetsCTE Table Saw Test
Total questions: 32
Worksheet time: 22mins
What should be done with articles of clothing such as ties, coats & long sleeves when operating the table saw?
Keep them away from the sawblade
Remove or fasten them out of the way
Do not get to close to the saw
Have a student hold them out of the way
Which of the following items should NOT be worn when operating the table saw?
Rings
Gloves
Bracelets
All of them
Personal Protective equipment which should be worn when operating the table saw is/are
Gloves
Ear protection
Safety glasses
Both B & C
When Setting the table saw up for a job, the saw blade should be checked for......
Stripped threads
Loss of temper
Cracks & missing teeth
Distorted arbor
The Arbor nut on the table saw is tightened only when......
It becomes loose
The electrical service is disconnected at the circuit breaker
The class is over by the teacher
Permission granted
To prevent slipping or falling when using the table saw......
Turn the saw off before removing material
Stay within the saefty zone
Do not over-reach when feeding material through the saw
Wear tennis shoes
When sawing with the table saw, which of the following would not be safe practice?
Use the blade guard
Secure A helper to support the material being sawed
Push the material through the saw with the right hand and a push stick
Stand in line with the saw blade
After a cut has been completed, what should the operator do before leaving the table saw
Turn the electrical service off at the circuit breaker or fuse box
Clear the work zone of all students
Make sure the saw blade has stopped turning
Lock the blade
When making a rip or crosscut, the saw blade should extend no more than ______ inches above the stock being cut
1/4
1/8
3/8
1/2
Which type of stock should never be ripped on the table saw
Square stock
Thick Stock
Round Stock
Flat Stock
Which of the following operations the use of a push stick on the table saw
Ripping narrow material
Crosscutting
Mitering
Dadoing
Which Table saw accessory gives width settings for the rip fence
Front rail/Table ruler
Rear table rail
Saw blade
Miter head
A push stick must be used if the material is less than ______ inches in width
4
6
8
10
The purpose of the off-bearer, in table saw operations, is to......
Pull the stock through the saw
Support the stock as it is pushed through the saw
Support and pull the stock through the saw
Remove scraps, support and help pull the stock through the saw
When ripping warped lumber the bow should be turned
Down
Up
Horizontally
It doesn't matter
The maximum distance the rip fence can be set from the saw blade is
36 inches
48 inches
12 inches on a 12 inch table saw
The distance measured when the carriage is flush with the end of the front rail
The accessory used when crosscutting on the table saw is
Front rail
Miter head
Fence
Table slot
When crosscutting. most table saw operators prefer to work on the ______ side of the saw table
Right
Left
Both
Neither
The miter head & right hand table slot are recommended for use when_____
Right angle rip cuts are to be made
Compound bevel crosscuts are to be made
Ripping short pieces
Ripping multiple cuts of the same size
When stock is held loosely against the miter head one may experience
Poor cuts
Binding of the blade
Material vibration
All of these
What # is the BLADE GUARD
(a)
What # is the TABLE INSERT
(a)
What is TABLE
(a)
What # is the MITER HEAD
(a)
What # is the BLADE TILT HAND WHEEL
(a)
What is TABLE SLOT
(a)
What # is the FENCE
(a)
What # is the FENCE LOCK
(a)
What # is the FENCE CARRIAGE
(a)
What is ON-OFF SWITCH
(a)
What # is the BLADE LOWERING & RAISING HANDWHEEL
(a)
What # is the FRONT RAIL
(a)
