wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

Fuel injection review 2

Total questions: 25

Worksheet time: 1hrs 15mins

Name
Class
Date
1.

Direct fuel injection sprays fuel...

a)

Into the pre cup

b)

Directly into the combustion chamber

c)

Underneath the piston

d)

From the side

2.

In an evaporative fuel system which valve(s) is (are) normally closed ?

a)

Canister purge valve

b)

Canister vent valve

c)

Both purge and vent valves

d)

Neither purge nor vent valves

3.

All of thefollowing can increase the pressure in the evaporative emission control system except _______?

a)

Fuel temperature

b)

Returned fuel from the fuel-injection system

c)

Inlet fuel at the fuel pump

d)

Volatility of the fuel

4.

Evaporative emission control systems operate on low pressure measured in inches of water (in. H2O) 28 in. H20 is equal to how many psi

a)

1

b)

5

c)

7

d)

14.7

5.

An enhance evaporative system is able to detect leaks of which size in the system ?

a)

.010 and .020 inch

b)

.040 and .060 inch

c)

.020 and .040 inch

d)

.060 and .080 inch

6.

Which evap valve is subject to rust ans corrosion more than all of the others ?

a)

Purge valve

b)

Vacuum control valve

c)

Vent valve

d)

Roll over check valve

7.

Before an evaporative emission monitor wil run, the fuel level must be where ?

a)

At least 75% full

b)

Over 25%

c)

Between 15% and 85%

d)

The level of the fuel in the tank is not needed to run the monitor test

8.

Technician A says that low pressure smoke installed in the fuel system can be used to check for leaks. Technician B says the nitrogen under low pressure can be installed in the fuel system to check for leaks. Which technician is correct ?

a)

Techncian A only

b)

Technician B only

c)

Both technician A and B

d)

Neither Technician A nor B

9.

The EGR valve is used to control which exhaust emission ?

a)

Unburned hydrocarbons (HC)

b)

Oxide of nitrogen (NOx)

c)

Carbon monoxide (CO)

d)

Both NOx and CO

10.

OBD II regulations require that the EGR system be tested. Technician A says that the PCM can monitor the commanded position of the EGR valve to determine if it is functioning correctly. Technician B says that the PCM can open the EGR valve and monitor for a change in the MAP sensor or oxygen sensor reading to detect if the system is fonctioning correctly. Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Both technician A and B

d)

Neither technician A nor B

11.

Two technician are discussing clogged EGR passages. Technician A says clogged EGR passages can cause excessive NOx exhaust emission. Technician B says that clogged EGR passages cancause the engine to ping (spark knock or detonation). Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Both technician A and B

d)

Neither technician A nor B

12.

An EGR valve is partially stuck open, would most likely cause what condition ?

a)

Rough idling or stalling

b)

Excessive NOx exhausts emissions

c)

Ping (spark knock or detonation)

d)

Missing at highway speed

13.

A P0401 DTC (exhaust gas recirculation flow insufficient) is being discussed. Technician A says that a defective EGR valve could be at cause. Technician B says that clogged EGR passages could be the cause. Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Both Technician A and B

d)

Neither Technician A nor B

14.

The PCV system controls which exhaust emission(s) ?

a)

Hydrocarbons (HC)

b)

Carbon monoxide (CO)

c)

NOx

d)

Both HC and CO

15.

Technician A says that if a PCV valve ratles, then its okay and does not need to be replace. Technician B says that if a PCV valve does not ratle, it should be replaced. Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Technician A and B

d)

Technician A nor B

16.

A blocked or PCV system may cause which of the following to occur ?

a)

Rough or unstable idle

b)

Excessive oil consumption

c)

Oil in the air filter housing

d)

All of the above

e)

None of the above

17.

Fuel injectors can be tested using ___________.

a)

An ohmmeter

b)

A stethoscope

c)

A scope

d)

All of the above

e)

None of the above

18.

Most port fuel injected engines operate on how much fuel pressure ?

a)

3 to 5 psi

b)

9 to 13 psi

c)

35 to 45 psi

d)

55 to 65 psi

e)

75 to 85 psi

19.

The vacuum hose from the fuel-pressure regulator was removed from the regulator and gasoline dripped out of the hose. Technician A says that isnormal and that everything is OK. Technician B says that one or more of the injectors may be defective, causing the fuel to get into the hose. Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Technician A and B

d)

Neither Technician A nor B

20.

The fuel pressure drops rapidly when the engine is turned off. Technician A says that one or more injectors could be leaking. Technician B says that a defective check valve in the fuel pump could be the cause. Which technician is correct ?

a)

Technician A only

b)

Technician B only

c)

Technician A and B

d)

Technician A nor B

21.

What components pulses the fuel injector on most vehicle ?

a)

Power train control module (PCM)

b)

Ignition module (IM)

c)

Crankshaft sensor

d)

Both B and C

e)

All of the above

22.

If the throttle plate needs to be cleaned, what symptoms wil be present regarding the operation of the engine ?

a)

Stalls

b)

Rough idle

c)

Hesitation on acceleration

d)

All of the above

23.

The fuel pump inside the fuel tank on a vehicle equipped with gasoline direct injection produces about what fuel pressure ?

a)

5 to 10 psi

b)

10 to 20 psi

c)

35 to 45 psi

d)

50 to 60 psi

e)

100 to 250 psi

24.

The high pressure fuel pump used in gasoline direct injection (GDI) systems arepowered by __________.

a)

Electricaly DC motor

b)

Electricaly AC motor

c)

The camshaft

d)

The crankshaft

25.

A lack of power from an engine equipped with gasoline direct injection could be due to ______________.

a)

Noisy injectors

b)

Carbon on the injectors

c)

Carbon on the intake valves

d)

Both B and C

e)

All of the above