Horizontal Structural member in a framed wall that provide lateral support to the wall panel

Maximum spacing between STIFFENER COLUMNS on ordinary CHB Wall is _____ Meters

MIN Thickness of CHB wall of a 1-Hr Fire Rating as per Code is ______

Stiffener beam is requireed for CHB wall if the wall height exceeds ________ Mts

When is the most important period of curing concrete for it to improve STRENGHT AND DURABILITY?

When using control joints son slab on grade, what is the depth of cut for a 4" THK concrete slab?

What compromises as much as 60% to 80% of a typical concrete mix to reduce cost

What is a good replacement for steel rebars on Large Area of Slab on Grade if ready mix concrete is used?

Durability and Strength improve in concrete mix when water to cement ratio is _________

Continuous footing that supports an entire heavy structure and reduces settlements on weak soil

What is often used on a sloping site where the foundation follow the slope without too much excavation?

Continuous strip of concrete supporting a continuous wall carrying a uniformly distributed load

What footing to use when ground bearing capacity is low and heavy columns are closely spaced

Footing used to support two parallel columns

What type of building will benefit the most from steel construction

When Specifying fireproofing for steel, which materials are the most expensive?

What is the Major Steel construction company in the Philippines

Who should be responsible for the structural steel design

In structural steel design, what does W4 x 13 stands for?

I-Beam used for steel column

Part of the I-Beam Section used for Structural Steel that resists Shear Forces

If I-Beam structural steel have equal or near equal width and depth, they are more suited as_________

Minimum curing / breaking of cylinder for compressive strength test

In site construction, backfilling materials are estimated by

Local Manufacturer of pre-stressed bars

Horizontal Spacing of rebars for firewall is every__________ layers

Refers to long, light gauge materials of various shapes and a non-structural metal attachment that is used to hold a finish material and a method of supporting one layer of material over another.

Minimum compressive strength fot Class A Concrete Mixture

Minimum Compressive Strength for Class C Concrete Mixture

Soil boring test must have a MIN depth of ________ mts

For every clear span of 4.0 mts, reinforced concrete beam should have a camber of at least _________ mm

Foundation should not rest on

Minimum Concrete Cover in MM for reinforcing bars of walls above grade

Minimum Concrete cover in MM for reinforcing bars of walls above grade

Max Slump for concrete in beams and slabs in MM

Common size of Rebar for both Vertical and Horizontal CHB walls in mm

Minimum Thickness of Concrete footing in MM

Crushed stone, crushed gravel or natural gravel with particles retained on a 5mm sieve is a __________ aggregate

What steel section is commonly used for EXPOSED structures

Strength of a 1:2 1/2:5 Concrete Mix

Column that raises/supports a mass of structure above ground

Long Column is designed for

Advantage of steel over concrete

Ready mix concrete should be tested _______

Water used for concrete mix

Minimum thickness of one way slab unless deflections are computed if simply supported

Most important determinant of Concrete Strength

Horizontal member in a building which is subjected to bending?

Type of wood column which consists of a single piece of wood, square or rectangular in cross sections?

Essentially vertical truss system of the concentric or eccentric type which is provided to resist lateral forces

Upper flexible portion of a structure having a vertical combination of structural system

A web found in a structural member

A brick wall is weak in

ALso known as elastic limit

When the beam is in its elastic limit, which among the situation below would most likely happen?

What component of steel dictates its ductility

What is the coincidence of the natural period of structure with the dominant frequency in the ground motion

This element at any transverse cross section of a straight beam is the algebraic sum of the moments taken about an axis passing through the centroid of the cross section, of all the loads and reactions apploed to the portion of the beam on either side of the cross section

which Standard specification should quality steel welded wire fabric for concrete reinforcement conform to