NEW
Font size
WorksheetsTractors
Total questions: 25
Worksheet time: 13mins
What is the name of the system we use to attach implements in this picture?
Three-Point
Draw Bar
Hitch
PTO
What should we check every 8 hours of work?
Air Filter
Oil
Transmission Fluid
Radiator Coolant
All of the Above
When starting the tractor, what should I do first?
Take off the parking break
Warm the glow plugs for 10 seconds
Raise the bucket
Put the tractor in range (low, medium, high)
What happens when you get off the tractor without putting the parking break on?
An alarm will sound reminding you to set the break
The tractor may roll away
We don't need to set the break as long as the bucket is down
Options 1 and 2
When using the bucket, which way should we pull the lever to raise the bucket?
Down
Left
Right
Up
What rpm should the tractor be above when working?
100
900
1200
1500
T/F A student can ride with another student as long as they are helping control the hydraulics
True
False
Think back to our farm cleanup. When moving heavy materials like dirt the tractor will need a ______ rpm.
higher
lower
unchanged
T/F We can never ride in the bucket of the tractor.
True
False
When dumping a load, the operator should not
Raise the bucket past the tipping point
Drive carefully to not dump the load early
Be aware of surroundings
Use a higher rpm
When should the PTO be attached to the tractor?
When using an implement that needs power
When using a static implement
When we are only using the bucket
When a trailer is attached to the tractor
When is it acceptable to have the throttle fully open (as far forward as possible)?
When driving to the job site
When starting the tractor for the day
When doing heavy work like lifting dirt or mowing with an implement
When inspecting the tractor
When is it acceptable to drive with the bucket obstructing my view?
The instructor is guiding me
Another student is guiding me
I am in an open field
Never
When attaching the three point, what should be attached first?
The arm bars
The PTO
The linch pins
The top link
What should we do if the top link can not reach the implement?
Reverse the tractor until it can reach
Lift the implement without the top link to free up some pressure
Drive forward to pull the implement towards the tractor
Adjust the top link to the right length by spinning the shaft
T/F The three point does not need linch pins put in place before moving the implement.
True
False
What type of transmission does the tractor have?
Standard
Automatic
Hydrostatic
CVT
When should a fluid leak be reported to the instructor?
After the job is completed
Once we are cleaning up for class
Immediately
When switching student drivers
T/F We must get permission to drive the tractor in class
True
False
When leaving the farm we should...
Go without the instructor since the bell is going to ring
Walk together and stay quiet for other classes
talk loudly to make sure we hear each other
walk at our own speed no matter where the class is
When attempting to scoop material with the bucket what should I do first?
Get the tractor in position with the bucket parallel with the ground
Drive into the pile I would like to pick up
Use the hydraulic controls to curl the bucket
Lift the load by pulling down on the hydraulic controls
When should we be close to a wide open throttle (the throttle pushed all the way forward)
When we are driving the tractor to our job site
When we are starting the tractor
When we move the bucket out of the way
When we are doing heavy work with an implement or the bucket
What should we do before leaving the tractor?
Lower the bucket to the ground
Take the tractor out of range
Put on the parking break
All of the above
When should we put on our seat belt?
After starting the tractor
After removing the parking break
After putting the tractor into range
As we are driving away
When reversing I should...
Look over my shoulder
Be aware of the bucket in front of me
Turn the the wheel opposite of the way I want to go
All of the above
