WorksheetsMSSC-Safety-9&10
Total questions: 32
Worksheet time: 16mins
Name
Class
Date
1.
The 3 prongs of a 110-volt power tool's power cord plug perform what purpose?
a)
One is the hot, one is the neutral, and one is the ground.
b)
One is the hot, one is the neutral, and one is the cheater.
c)
Two of them conduct electricity, and the third holds the plug in the outlet.
d)
Two of them are for AC current, and the third is used for DC current.
2.
Tools operated electrically or by pneumatic power are classified as __________ tools.
a)
Power
b)
Mechanic
c)
Hand
d)
Handyman
3.
Oxidizers, fuels, and flammable gases should be stored at least __________ from any ignition sources.
a)
10 feet
b)
20 feet
c)
50 feet
d)
100 feet
4.
The first step in safe hand tool use is __________.
a)
Only use a tool for its intended use
b)
Wear the proper personal protection equipment
c)
Be cautious using worn or damaged hand tools
d)
Alter tools to fit a task
5.
The contents of a gas cylinder are only determined by __________.
a)
The color of the tank
b)
Type of service valve
c)
Reading the cylinder label
d)
Opening the valve and smelling the gas
6.
When using compressed air to clean work areas, air pressures should be kept below what limit?
a)
30 psig
b)
25 psig
c)
20 psig
d)
15 psig
7.
Power tools are more dangerous than hand tools because they __________.
a)
Are connected to a power source
b)
Are heavier and bulkier than their hand tool counterpart
c)
Operate at higher speeds and forces
d)
Are by nature difficult to operate
8.
When is it okay to alter a hand tool?
a)
To increase torque
b)
To increase the number of jobs for which the tool can be used
c)
Both A & B
d)
None of the above
9.
How far apart should oxygen cylinders be stored from flammable materials?
a)
5 Feet
b)
10 Feet
c)
15 Feet
d)
20 Feet
10.
What device is used to protect the valve stem of a compressed gas cylinder?
a)
Restraining chain
b)
A dolly or handcart
c)
Steel safety cap
d)
A stainless steel regulator
11.
What word describes the types of gas that help a fire burn?
a)
Inert
b)
Oxidizer
c)
Flammable
d)
None of the above
12.
As a safety precaution, which of these should be chained to a rigid fixture?
a)
A compressed gas cylinder
b)
A forklift
c)
A drill press
d)
A welder
13.
Which of the following is NOT a common type of hand tool?
a)
Phillips screwdriver
b)
Pliers
c)
Circular saw
d)
Hex key
14.
What safety device is used as a last resort to keep robot from physically moving a certain point?
a)
Mechanical stop
b)
Teaching pendant
c)
E-stop
d)
Proximity sensor
15.
If the load obscures the view forward, the operator should __________.
a)
Reduce the load
b)
Drive slowly
c)
Drive the forklift truck in reverse
d)
Lower the load
16.
What type of crane is used to move a hoist within a single industrial facility?
a)
Overhead crane
b)
Gangry crane
c)
Jib crane
d)
Boom crane
17.
All safeguard devices should be __________ before operating a robot work cell automatically.
a)
Inspected
b)
Programmed openly
c)
Activated
d)
Connected
18.
Cranes can only be operated by a __________.
a)
Safety engineer
b)
Forklift truck driver or crane operator
c)
Certified crane operator or a supervisor
d)
Certified crane operator
19.
The Occupational Safety and Health Administration (OSHA) requires __________ forklift safety inspections.
a)
Hourly
b)
Weekly
c)
Daily
d)
Monthly
20.
Rules are designed to protect the operator and the robot equipment. The operator must follow and complete the safety system and training, locate the emergency stops, and __________.
a)
Monitor the controls and nearby personnel
b)
Monitor the material handling of the robot
c)
Maintain and monitor the parts being produced
d)
Complete a quality check on each part produced
21.
Why is it a good idea to dispose of damaged rigging equipment?
a)
So it is not accidentally used again.
b)
To avoid secondary inspections.
c)
This ensures a constant supply of good rigging equipment.
d)
To reduce an inventory surplus.
22.
When is it ok to use a hoist to lift something that weighs more than the rating on a hoist?
a)
When it does not exceed 5 percent of capacity
b)
Never
c)
When the load is lifted carefully
d)
When it does not exceed 10 percent of capacity
23.
Which of the following lifting devices do industrial workplaces use for moving loads?
a)
Forklifts, hoists, and overhead cranes
b)
Platform lifts, hoists, and chain falls
c)
Manual lifts, platform lifts, and scissor lifts
d)
Derricks, tower cranes, and scaffolding
24.
A robot's teach pendant should have a __________ on it to stop the robot's motion immediately.
a)
Light curtain
b)
Lockout hasp
c)
Keyed interlock
d)
Emergency Stop
25.
A __________ is a manually operated forklift.
a)
Pallet jack
b)
Hand truck
c)
Pry truck
d)
Dolly
26.
OSHA requires that a person who operates a forklift __________.
a)
Be at least 21 years of age
b)
Have a valid automobile driver's license
c)
Be trained and certified
d)
Have a commercial driver's license
27.
Which of the following is NOT considered a robot safety device?
a)
Barricades
b)
Light curtains
c)
Deadman switches
d)
Steel-toed boots
28.
Many of the safety devices for the robot are designed to protect the human interaction with the robot. Which device can detect when a person is near the robot arm or if the arm has touched a person?
a)
Emergency stop
b)
Light curtains
c)
Barricades
d)
Collaborative robot system
29.
When an operator must be inside the work cell to teach points with a teach pendant, which additional safety rule(s) should be followed?
a)
The robot must be in the teach mode.
b)
A swift jogging speed must be set.
c)
No other workers should be present.
d)
All of the above
30.
Which of the following is responsible for most robot-related, industrial accidents?
a)
Sudden, unexpected movement
b)
Improper interlock systems
c)
Poor training practices
d)
Incorrect teach pendant programming
31.
What is rigging?
a)
Moving an unbalanced load
b)
Securing a load in order to move it
c)
The use of furls, eye sockets, and tethers
d)
The use of forks, levels, and nylon cables
32.
What type of safety device is used to stop welding robots?
a)
Proximity sensor
b)
Spark hammer
c)
Kerf curtain
d)
Welding mask
100 %
