Font size
WorksheetsNCCER - Spring Modules
Total questions: 166
Worksheet time: 1hrs 23mins
When using an air wrench, or any power tool _____.
keep your body stance balanced
hold onto the compressor hose with one hand
hold the impact socket a few inches away from the material
use handheld sockets that are the right size
Before you plug any saw (or any power tool) into a power source, make sure the _____.
power switch is in the OFF position and switch lock it off
speed is set to LOW
work has been clamped down
lower blade guard is pulled back
The first step when using a pneumatically powered nailer (or any tool) for the first time is to
inspect the nailer for damage
load the nails into the nailer
check the air compressor
read the manfacturer's instructions
Saws with smaller blades that are excellent for delicate and intricate cutting are called _____.
abrasive saws
saber saws ( jig saw )
bandsaws
worm-drive saws
A pneumatic drill is used _____.
for work too heavy for an electric drill
to supply compressed air to clean the inside of pipes
when there is no source of electricity
for intricate work
If a pneumatic nailer ( or any power tool ) is not working properly, before you attempt repairs you must _____.
adjust the compressoer
disconnect the air hose (power source)
adjust the regulator
remove the booster
Never use a circular saw (or any power tool) that doesn't have its guards in place because the _____.
trigger lock will not work properly
saw will not cut cleanly
guard protects you from touching moving parts
saw kerf will be too wide
The tool rest on a bench grinder should be positioned no more than _____ inch from the wheel.
1/8
1/4
1/2
3/4
Some manufacturers suggest that each time you use their air tools, that the air inlet needs _____.
a few drops of oil
a few drops of water
a shot of compressed air to clear any dust
to be cleaned with a small wire brush
Before replacing parts such a bits, blades or discs on any tool, you must _____.
polish it with a fine steel wool
recharge the tools's battery
disconnect the power source
inspect them for cracks
Before connecting any power source, it is critical to ______.
make sure the tool has been cleaned and oiled
ask your supervisor for permission
confirm the power switch is set to OFF
confirm the condition of all the tool's attachments
When using power tool's, NEVER engage the _____.
locking spring
booster
bit shank
trigger lock
Before replacing parts such as bits, blades, or discs on any tool, it is important to ______.
disconnect the power source
recharge the tool's battery
polish it with fine steel wool
check the tool's oil level
The part of a drill that holds the drill bit in place is called the _____.
auger
ram
shank
chuck
When using an appropriate bit, variable speed drills can be used like a(n)_____.
hammer drill
impact driver
screwdriver
mag drill press
Before using a hammer drill or rotary hammer to drill into concrete, it is important to _____.
install a flying debris guard on the drill chuck
review silica exposure standards
confirm the location of coworkers
spray down the concrete surface with water
A pneumatic drill is commonly used ____.
when electricity is unavailable
to drill in tight, small areas
in areas where noise is a problem
to perform precision work
Never use a circular saw that does NOT have an upper blade guard because the _____.
trigger lock will not work properly
safety features will be disabled
exposed blade poses a danger
saw kerf will be too wide
The most important maintenance on a circular saw involves the ____.
upper blade guard
blade's sharpness
battery charge
lower blade guard
When using a circular saw, be sure to cut on the waste side of the cut mark to allow for the blade's ____.
uptake
stroke
angle
kerf
Saws with fine blades that are excellent for delicate and intricate cutting are called _____.
jigsaws
bandsaws
abrasive saws
worm-drive saws
The coarseness of a bandsaw's blade is rated in __?
Revolutions per minute
teeth per inch
length of the blade's teeth
hardness of the blade's teeth
A power miter saw combines a miter box with a __?
bandsaw
jigsaw
reciprocating saw
circular saw
Crosscutting means that you are cutting the wood __?
with the grain to a specific width
with the grain
across the grain to a specific length
before the wood cures
An angle grinder is used to grind ___?
hard, heavy materials
imperfections in wood
soft, porous materials
nonmetals only
The grinder type BEST suited to sharpening worn edges on cutting tools is the _____.
detail grinder
angle grinder
end grinder
bench grinder
The adjustable tool rest on a bench grinder should be positioned ____.
1/8 inch from the grinding wheel
1/4 inch from the upper wheel guard
1/2 inch from the lower guard
3/4 inch from the wheel arbor
When using a grinder, two of the most important pieces of PPE are ____.
hard hat and rubber footwear
face mask and ear protection
gloves and safety glasses
ear protection and gloves
A type of grinder accessory that can be used to provide a stable surface for flexible sanding discs or buffing pads to rest against is called a(n) _____.
flap disc
arbor shield
backing pad
tool rest
A compact tool that operates by moving attachments back and forth at very high speeds is the ______.
compound miter
oscillating multi-tool
impact driver
table saw
A low velocity fastening system used to drive steel pins or threatened studs into masonry and steel us a(n) _____.
pneumatic screw nailer
powder-actuated tool
air impact wrench
mini hammer drill
Compared with powder-actuated nailers, electric and pneumatic nailers ____.
are both stronger
require more training
do not require certification
are much slower
Before using a pneumatically powered nailer for the first time, is it important to _____.
disassemble the nailer for inspection
load the nails into the nailer
ensure it is plugged into a GFCI receptacle
read the manufacturer's manual
Most craftworkers who use pneumatic nailers operate their compressors at ___.
30 tp 80 psi
60 to 110 psi
70 to 120 psi
90 to 140 psi
A Porta-Power is an example of a(n) _____.
electric tool
pneumatic tool
hydraulic tool
battery-powered tool
Gridlines are used to _____.
indicate a cross-section of material
make it easy to refer to specific locations on the plan
indicate land boundaries on the site plan
indicate that an object has been broken off
A keynote is a number or letter that is used with a leader and arrowhead to identify a specific object; it usually appears in _____.
a square or circle
the upper right-hand corner
the upper left-hand corner
block letters
Site plans are developed using a(n) _____.
engineer's scale
architect's scale
1/4" = 1'-0" scale
NTS scale
Information about the structure or assembly is provided in the _____.
drawing area
border
title-block
legend
In the alphabet of lines, an area not included in the cutting line view is shown with _____.
object lines
section cuts
break lines
dimension lines
The identification of lines and other symbols on a construction drawing is called the _____.
index
title block
scale
legend
On the drawing, a project is identified by the _____ found in the title block.
sheet title
legend
scale
company logo
Plans used for work that has to do with construction in or on the earth are called _____ plans.
structural
architectural
exterior
civil
The architect's scale is used for drawing _____.
plot plans
floor plans
cut lines
specifications
To clarify any discrepancies in the plans, the foreman should use a(n) _____.
title block
RFI
index
legend
The material to be used for the walls would be found on the _____ plan.
civil
plumbing
structural
mechanical
To avoid confusion, the letters, I. O. and Q and the numbers 1 and 0 are sometimes omitted from the _____.
contour lines
grid-line system
NTS drawings
title block
A dimension is a measurement written as a _____.
range
number
symbol
letter
Break lines are used to show that _____.
only part of the object is represented to save space
an object will appear in a separated drawing
an object is not included on the cutting line view
an object is hidden
To clarify information that cannot be shown on the drawings, the architectural and engineering firm will prepare _____.
contracts
a proposal
specifications
a change order
What information in a drawing's title block identifies the project?
Sheet title
Company Logo
Drawing Number
Revision Block
The information needed to identify lines and other symbols on a construction drawing can be found in the ___.
Index
Title block
Legend
Scale
Break lines are used to show that___.
an object will appear in a separate drawing
an object is hidden
only part of an object is represented to save space
an object is not included on the cutting line view
Which statement concerning symbols used on plans is true?
only carpenters use symbols
the same symbols are used on all plans throughout the world
the symbols are to be noted on the title or introductory sheet
symbols are never replaced by keynotes
A dimension is a measurement written as a ___.
range
number
letter
symbol
On a site plan, the scale may read SCALE: 1" = 20' 0". This means that ___.
every inch represents 20 inches
every inch represents 20 feet
every foot represents 20 inches
every foot represents 20 feet
The triangular architect's scale is the most commonly used because___.
can combine multiple scales
provides greater accuracy due to its shape
is more rugged on job sites than other scales
is more accurate than other types of scales
Plans that show an aerial view of the building site location are called___.
civil plans
architectural renderings
structural foundations
exterior views
The materials to be used for the walls would be found in the ____?
plumbing plan
structural plan
civil plan
mechanical plan
What are engineered plans for motors, pumps, piping systems, and piping equipment called?
Instrumentation drawings
Detail drawings
Foundation plans
Mechanical plans
The maximum load weight that a sling is designed to carry is the ____?
top weight
carry weight
rated capacity
load capacity
Most alloy steel chain slings can be used in temperatures up to____?
200F
300F
400F
500F
When a tattle-tail has been pulled into the jacket of a synthetic sling, the sling most likely has been ___?
chemically damaged
overheated
overloaded
crushed
If a wire rope sling appears to be damaged, the decision to keep it in service must be made by a ___?
site supervisor
district manager
competent person
crane operator
Because of the need for increased toughness, shackles for most overhead lifting are made from ___?
cast steel
forged steel
drop iron
tempered aluminum
Which style of hook is designed to be used on alloy steel chain slings?
Grab Hook
Eye Hook
Sliding Hook
Short Hook
To lift heavy loads, all chain hoists us a(n) ___.
sprocket set
anchorage slide
gear system
hook retainer
A type of hand-operated winching device that should never be used for vertical overhead lifting is a ___.
chain hoist
come-along
block and tackle
ratchet lever hoist
Two choker hitches are recommended when lifting a load longer than ___.
6 feet
8 feet
10 feet
12 feet
If an emergency stop occurs during a rigging operation, who is allowed to five the emergency signal?
Only another crane operator close by
Only the signal person
Only a qualified rigger
Anyone who is in site of the crane operator
The advantage of a ______ is that they are flexible, light, and mold themselves to the shape of the load.
Synthetic Sling
Steel Chain Sling
Wire Rope Sling
Cable Sling
To let the rigger know is a sling has too much wear or damage, most slings are made with _____?
Red-core warning yarn
Tattle-tail
Small abrasion patch
Warning Tabs
If an alloy steel chain has a missing or illegible identification tag what must be done?
Remove it from service
Type up a new tag
Check with the safety supervisor
Nothing is required
If a sling or wire rope damaged who decides to discard it or use it?
Safety Supervisor
The Foreman
A Competent Person
Anyone on the ground can
What is the coupling device used to connect slings, ropes and other types of connectors
Shackle
Bull Nose
Coupler
Sling Ring
A configuration using two or more slings to connect a load to a single hoist hook.
Strand
Bridle
Load Control
A single ring used to attach multiple slings to a hoist
Load Stress
Sheave
Bull Ring
An individual who is capable of identifying existing and predictable hazards or
working conditions that are hazardous,
unsanitary, or dangerous to employees,
and who has authorization to take prompt,
corrective measures to eliminate or
control these hazards and conditions
Competent Person
Qualified Person
Hitch
A device used to move loads such as steel plates or concrete panels without
the use of slings.
The rigging configuration by which a sling connects the load to the hoist hook. The
three basic types of hitches are vertical,
choker, and basket.
Hoist
a device that applies a mechanical force for lifting or lowering a load
the total amount of what is being lifted, including all slings, hitches, and hardware
A device used to move loads such as steel plates or concrete panels without
the use of slings.
Hitch
Hoist
Lifting Clamp
The maximum load weight a sling or piece of hardware or equipment can hold
or lift. Also called lifting capacity, working
capacity, working load limit (WLL)
Rated Capacity
Load Rating
Load
A coupling device used to connect the rope to eye fittings, hooks, or connectors
Hook
Shackle
Bridle
Sling
Wire rope, steel chain, metal mesh fabric, and webbing that is made into forms used to handle loads
a surface in which a straight line joining two points lies wholly within that surface
a device that applies a mechanical force for lifting or lowering a load
Tattle Tail
The rigging configuration by which a sling connects the load to the hoist hook. The
three basic types of hitches are vertical,
choker, and basket.
A cord attached to the strands of an endless loop sling. It protrudes from the jacket. Used to determine if an endless sling has been stretched or overloaded.
A type of hand-operated winching device that should never be used for vertical overhead lifting is a ____
Chain Hoist
Come-Along
block and tackle
ratchet lever hoist
To lift heavy loads, all chain hoists use a(n)
Sprocket set
anchorage slide
gear system
hook retainer
a component of a sling that shows if the sling has suffered too much damage to be used. Normally this cannot be seen until damage has occurred.
warning yarn
wire emergency cord
unstranding
load control device
The type of rigging hook that are used on steel chain slings, the hook fits securely in the chain link.
Rigging Hook
Grab Hook
Eye Hook
Choker Hook
Special features in books that help you locate information include _____.
illustrations
dictionaries and encyclopedias
tables of content, indexes, and glossaries
footnotes
Talking on the phone in front of co-workers, supervisors, and customers is _____.
acceptable if you keep your voice low
necessary when ordering materials
effective communication
rude and unprofessional
If you do not understand what a speaker is saying, _____.
ignore that part of the conversation
try to figure it out on your own
ask someone else what they think the speaker means
ask the speaker questions for clarification
What is an important practice in writing to avoid errors that can cost time and money?
Use of industry jargon
Mastering composition
Accuracy
Writing long explanatory sentences
With email, nonverbal communication is lost and your message must be carefully composed to avoid being _____.
rejected as spam email
misinterpreted by the recipients
forwarded to others
legally binding
To make sure your points are understood in an email, you can ______.
use all capital letters to emphasize important items
copy other recipients so that they can explain any unclear items
write in a concise format using bulleted or numbered items
copy supporting documents into the email
When reading instructions or a series of steps, you should _____.
only reed the steps you don't know
perform the steps even if you don't understand them
read the directions completely
skim the directions quickly
An important attribute of an effective speaker is the ability to _____.
inject humor on the job site
explain and simplify complex topics
conduct multiple conversations with workers
correct workers who ask the wrong questions
When communicating on the job, you should _____.
finish quickly to avoid lost time on the project
assume that everyone is familiar with industry jargon
maintain eye contact and encourage listeners to take notes, if necessary
interrupt your co-workers, if necessary
When listening to instructions, the best way to make sure you get all the information is to _____.
take notes and compare them with other co-worker's notes
read a book about the topic later on
ask questions, but wait until the person has stopped talking
take notes, ask questions at appropriate times, and repeat a summary of the instructions.
In the study of communication, noise is best defined as ___.
people interrupting someone who is thinking
anything that interferes with the message being heard or understood
thoughts that distract the listener
discussing things that are off the main topic
Folding your arms in front of you make make it seem as if your are___.
warm and friendly
happy and relaxed
distant and unwilling to talk.
the group leader
If someone does not understand what a speaker is saying, he or she should ___.
ignore that part of the conversation
try to figure it out on your own
ask other people
ask the speaker questions
When listening to instructions, the bet way for listeners to make sure they get all the information is to ___.
take notes and compare them with other peoples notes
read a book about it later
ask questions, but wait until the person has stopped talking
take notes, ask questions and repeat a summary of the instructions
An important attribute of an effective speaker is the ability to ___.
inject humor on the job site with practical jokes
explain simplify complex topics
conduct multiple conversations with workers.
make others feel inferior.
Common documents that construction professionals need to read on the job include ___.
construction drawings, code books and manuals
legal briefs, permits and subpoenas
contracts, warrants and enecylopedias
literary reviews argumentation papers and essays
Special features in books that help readers locate information include ___.
drawings and photos
dictionaries and encyclopedias
table of content, index and glossary
safety-related cautions and warnings
When reading instructions or a series of steps, you should ___.
read only the steps you don't know
do the steps even if it doesn't make sense
read the directions completely
skim the directions quickly
The rough draft of a document you are writing should ___.
follow an outline and incorporate your research
be as close to perfect as possible
be complete before research is done
be complete before an outline has been created
What is an important practice in writing to avoid errors that can cost more time and money?
Handwriting the paper before using a computer
Write in the form of a question
Proofread the work for accuracy
Writing at a high reading level
If you see a potential source of delay on a project, _____.
Ask a co-worker to determine the problem
stop working on your task until the problem is solved
notify the supervisor immediately
monitor the problem until it reaches an urgent stage
The way you speak, act and interact is called _____.
work ethic
personal habit
professionalism
self-presentation
Being dependable means _____.
showing up for work on time, every day
reporting co-workers who stretch out lunch hours and breaks
leaving work early once you've finished a task
finishing tasks no earlier than their scheduled date
The process of interacting with another person or group is a _____.
partnership
clique
priority
relationship
You will never stop learning better ways to solve problems if you are open to _____.
overtime
promotion
change
evaluation
The contribution of each member of a group toward a common goal is called _____.
cooperation
collaboration
teamwork
distribution
A common problem on the job site that contributes to delays is _____.
closed-mindedness
fear of change
absenteeism
personality conflicts
Critical thinking is the process of _____.
evaluating information, then reaching a conclusion or making a decision
searching for jobs, then applying and interviewing
distrusting new ideas
evaluating the need, then developing business and marketing plans
Getting along with co-workers and thinking critically are examples of _____ skills.
interpersonal
technical
personal
behavioral
A company's documented philosophy is called its ___.
business plan
administrative structure
organizational structure
mission statement
The time to learn about potential employer is ___.
before the application is submitted
before the interview
during the interview
during the first week of employment
When preparing a resume, you should___.
use a font that is very creative and expressive
format the information chronologically
avoid any use of bulleted lists
not mention any certifications until an interview
During a job search, it is a good practice to___.
apply for positions that require less skill to better your chances
apply for positions that require greater skills to show your potential
avoid any job that will likely require additional learning
look for jobs that match your skills and experience
Before employment begins, candidates for construction jobs must often___.
pass a rescue's and first aid test
take and pass a drug test
pass a driving test
be capable of lifting their own weight
Most employers advertise job openings ___.
in the local newspaper only
at the front desk
on the Internet
directly on organization chart
Conflict resolution is considered to be___.
an importation relationship skill
a sign of good welder
unacceptable in the workplace
a sign of weakness
To resolve a conflict with a co-worker, it is best to___.
immediately tell your supervisor
first admit there is conflict
ignore it
think about it for while
It is not professional to offer construction criticism if you___.
do not know the other person
cannot get along with the other person
cannot suggest an alternative method
give an opinion
A worker verbally abusing another worker consistently, sometimes physically, and there is an imbalance of power between the two. This likely falls into the category of ___.
racism
age discrimination
sexual harassment
bullying
Working with other to meet common goals is an example of ___.
teamwork
technical skills
critical thinking
behavior skills
Being self-confident and a effective communicator are signs that a worker may be a(n) ___.
bully
leader
ineffective craftworker
undependable
Critical thinking is the process of ___.
evaluating information, then making a decision
searching for jobs, then applying and interviewing
distrusting new ideas
evaluating the need, then developing business
You will never stop learning better ways to solve problems if you are open to __.
overtime
promotion
change
evaluation
When a problem-solving team includes a close-minded person, that individual is one who ___.
does not get along with others
lacks work ethics
tries to sabotage the project
distrusts any new ideas and resist change
The first step to solving a problem is to ___.
find a solution
define it
ask for help
have a plan
A common problem on the job site that contributes to delays is ___.
close-mindedness
fear of change
absenteeism
personality conflicts
If you see a source of delay on a project ___.
ask a co-worker to determine the problem
stop working on your task until the problem is solved
notify your supervisor immediatly
monitor the problem
The way you speak, act and interact with others is referred to as your ___.
work ethic
fear of change
professionalism
self-presentation skills
Being dependable means ____.
showing up for work on time, every day
reporting co-workers who stretch out lunch breaks
leaving work early once you've finished a task
finishing task no earlier than their scheduled date
To lower the center of gravity when moving materials, you should always place the _____.
lightest load on the bottom
longest load on top
heaviest load on the bottom
heaviest load on top
What is the appropriate vehicle to use for lifting and moving heavy loads on smooth surfaces?
Georgia buggy
Industrial forklift
Pipe transport
Powered wheelbarrow
What is the proper procedure to lift objects?
Bend over with your knees straight, feet together, and then lift.
Lift with your back, keep your legs straight, and keep your arms up.
Lift with your legs, keep your back straight, and keep your head up.
Lift with your arms, keep your legs straight, and keep your head up.
In order to work with motorized materials-handling equipment, you must be _____.
trained, certified, and authorized
experienced and knowledgeable
a job foreman or supervisor
licensed to drive
Before attempting to lift any material, you should _____.
look for any protruding nails, wires, or sharp edges
use a safety harness
ask your supervisor for help
ensure the stacking ratio is no greater than 3:1
What non-motorized materials-handling device uses force applied with a lever, screw, or hydraulic press to raise heavy objects?
Industrial forklift
Porta-Power
Hand truck
Jack
Before using a materials handling device, you must ______.
inspect it
clean it
lubricate it
charge it
When moving a material cart on an inclined or declined surface, you must be sure _____.
the load does not exceed the labeled weight capacity
the hand brake is within you reach
the hydraulic ram has been removed
the load is cushioned with moving pads to prevent slippage
When using hand signals, you must always _____.
be certified and authorized
wear reflective gloves
keep eye contact with the operator
make sure you can hear the backup alarm
What is the diameter of the fall zone when working around a forklift?
A minimum of thirty feet
Twice the length of the base of the forklift
Twice the height of the object being lifted
Twice the width of the object being lifted
What device may have a rotating table surface and/or spikes on the table surface for better grip?
Roller skids
Pallet jack
Pallet conveyor
Accumulating conveyor
In materials-handling jargon, the quantity of materials that can be transported at one time by a machine or vehicle is called a _____.
stack
load
shipment
consignment
To prevent a tip-over when driving a rough terrain forklift, keep the load ___.
Light
Low
High
Heavy
The forklift hand signal for "dog everything" means ___.
to lower the tines
to tilt the mast back
to creep forward
to pause
When stacking bags of material that are the same width, step back and cross key the bags ___.
each tier above seven feet
until the stack reaches four feet
every 10 bags high
all the way to the top
NEVER stack or store materials ___.
in cabinets
on scaffolds
outdoors
on pallets
The knot shown in the figure provided is a ___.
square knot
clove hitch
half hitch
bowline
