WorksheetsQuiz #2
Total questions: 31
Worksheet time: 4hrs 53mins
Which one of the following statements is true regarding the Clutch Cover?
It is splined onto the input shaft
It is splined to the Clutch Disc
It is bolted to the Flywheel
It is bolted to the Input Shaft
What is the purpose of the springs in the image shown?
Absorbs shocks when the drive is taken up
Pushes the hub away from the Flywheel
Allows an increased clamping force
Prevent Clutch slip when the drive is taken up
In regards to Clutch Operating Cylinder; which one of these statements is true?
It's sealed and never needs a fluid level check
It's attached to the Clutch drive plate
It uses air as the operating medium
It's attached to the Clutch Release Mechanism
What is the first thing to check when a hydraulically operated clutch fails to disengage?
Pressure Plate
Transmission Leaks
Clutch fluid level
Cable Adjustment
Identify this component
Wheel
Flywheel
Dual Mass Flywheel
Clutch
What component can temporarily disengage drive from the engine to the gearbox?
Transmission
Cogs
Flywheel
Clutch
What component connects the rotating clutch with the stationary release mechanism?
Shell bearing
Wheel bearing
Release bearing
Release fork
What does a clutch allow?
engine to provide a braking force downhill
means of giving an overdrive ratio in 5th gear
decrease in engine power as engine speed decreases
gradual take up of drive from the engine
What is the purpose and function of a transmission?
Allows the vehicle to accelerate up a hill
Allows the engine to accelerate the vehicle
Allows engine speed to be reduced at higher speeds to save fuel
All of the above
Which part is splined to the clutch disc?
Main shaft
Countershaft (lay shaft)
Main gear
Cluster shaft
In a manual transmission, engine torque is applied to the ________ when the engine is running and the clutch is engaged.
Cluster gear
Input shaft
Main gear
All of the above
The free rotating gears on the main shaft of a RWD manual transmission are called ________ gears.
Hypoid
Speed
Fixed
Floating
Which part of a synchronizer is splined to a shaft?
Synchronizer sleeve
Hub
Speed gear
Synchronizer blocker ring
A customer complained of hard shifting, particularly into first gear and reverse. Technician A says that the blocking ring maybe worn. Technician B says that the clutch may be defective or out of adjustment. Which technician is correct?
Technician A only
Technician B only
Both technicians
Neither technician
A five-speed transmission is in third gear. Which is correct?
The 1-2 synchronizer is in neutral
The 3-4 synchronizer is moved to engage third gear
Both A and B
Neither A nor B
A four-speed transmission is making a grinding noise only while shifting into second gear. This could be caused by ________.
A damaged main drive gear
A faulty 1-2 synchronizer sleeve
Either A or B
Neither A nor B
When one synchronizer is shifted into gear, the movement of the other shifter forks is blocked by the ________.
Detents
Interlocks
Both A and B
Neither A nor B
A five-speed manual transaxle is noisy in all gears. Which is the least likely cause?
A pilot bearing
An input shaft bearing
An output shaft bearing
Final drive side (differential) bearings
The idler gear is used for which gear?
Second
Reverse
Third
First
10. A ball nut on bearings is meshed with the worm gear and screws up and down relative to the movement of the worm is called ________.
worm and sector steering
ball joints
recirculating ball steering
tie rod ends
The type of the steering system shown in the figure is a/an :
- Front-wheel steering system:
- Rear-wheel steering system:
- Four-wheel steering system:
The type of the steering system shown in the figure is a/an :
- Front-wheel steering system:
- Rear-wheel steering system:
- Four-wheel steering system:
The type of the steering system shown in the figure is a/an :
Rack and pinion steering system
Linkage (pitman arm) type
The component shown in the figure is a steering
Steering wheel
Pitman arm
Steering column:
Steering gearbox:
The component shown in the figure is a steering
Tie-rod
Idler arm
Drop arm
Track rod
Identify the steering system component in the image.
Steering box
Steering rack gaitor
Steering column
Track rod end (TRE)
Identify the steering system component in the image.
Steering box
Steering rack gaitor
Steering column
Track rod end (TRE)
Identify the steering system component in the image.
Steering column
Steering box
Steering rack
Track rod end (TRE)
Identify the steering system component in the image.
Steering box
Steering rack gaitor
Steering column
Track rod end (TRE)
Identify the steering system component in the image.
Steering Wheel
Steering rack gaitor
Steering column
Track rod end
Identify the steering system component in the image.
Steering Wheel
Steering rack gaitor
Steering knuckle/Hub Assembly
Track rod end
