NEW
Font size
WorksheetsShop Review
Total questions: 50
Worksheet time: 33mins
When is a push stick used on a band saw?
Only when cutting thin wood
Only when cutting round objects
Whenever possible
Only with the machine off
Which is greater in terms of measurement?
1 5/16"
1 1/12"
1 3/4"
1 7/8"
What is half of 3/8"?
1.5mm
3/16"
5/32"
none of the above
What is the smallest unit of measurement on a standard tape measure?
1 mm
1/16"
1/8"
1/2"
How can you quickly determine if a ruler is Standard or Metric?
Metric ruler has 10 divisions
Standard ruler has 15ths.
Standard ruler is based on a system of tens
Metric ruler has inches
What units of measure are shown on the ruler?
Centimeters
Standard
Scientific
Metric
1 inch is...
equal to 1.275 centimeters.
shorter than 1 centimeter.
longer than 1 centimeter.
No correct answer available
Never use a power tool or equipment that has a _________ power cord.
electrically grounded
plugged in
damaged
short
What is the measurement shown on the ruler?
(Assuming that the bar started at 0.)
4 8/8"
4 3/4"
4 7/16"
4 1/2"
What is the measurement shown on the ruler?
(Assuming that the bar started at 0.)
3 3/16"
3 2/4"
1 1/8"
3 1/8"
What is the measurement shown on the ruler?
(Assuming that the bar started at 0.)
11 12/8"
11 3/8"
11 5/8"
11 3/4"
What is the measurement shown on the ruler?
(Assuming that the bar started at 0.)
10 3/8"
10 3/16"
10 1/4"
No answer available
What is the measurement shown on the ruler?
(Assuming that the bar started at 0.)
10 3/8"
10 5/16"
2 5/16"
10 5/8"
Most accidents are caused by...
human error
expensive tools
machine failure
tool failure
The best PPE for the prevention of eye injuries is...
safety glasses
dust mask
closed toed shoes
hard hat
Always ______ your machine to make adjustments or measurements.
speed up
turn off
slow down
turn on
Before operating a machine tool, you should...
think about what you are about to do
ALL answers are correct
make sure all safety guards are in place
remove rings and other jewelry
It is always important that the first impression of an interview be...
a lasting positive one
happy
not important
long
What is the purpose of the Compound Miter Saw?
cut materials to length
measure angles on dimensional lumber
cut metal materials
Cut handheld pieces shorter than 6"
The blades, knife, or bits used with power tools must be ___________ and in good condition.
dull
electrically grounded
overloaded
sharp
A piece of walnut that measure 1" thick by 12" wide by 24" long has______.
1 board foot
2 board feet
1.5 board feet
.5 Board foot
Safety glasses should be worn...
only when working on machines
most of the time
the entire time you are in the shop
no correct answers present
Which of the following is the responsibility of OSHA?
restrict the use of asbestos or other harmful materials in the workplace
figure out the hospital costs associated with workplace injuries
determine career salaries
ensure safe and healthy working conditions in the workplace around the world
Flip flops(and/or slides) are a violation of OSHA safety rules for Manufacturing and Construction areas.
TRUE
FALSE
On the compound Miter saw you should always...
Secure your workpiece to the fence and table
Cut curved shapes and circles
cut steel with a forceful quick motion
hold short pieces(less than 6") close to the blade
If you hear an unusual noise coming from the machine, what should you do?
Alert a coworker nearby
Ignore it and continue working
Fix the machine yourself
Turn the machine OFF and let your Supervisor know
The first consideration by the potential employer should be your...
knowledge of current events
qualifications and experience
religious beliefs
racial heritage/ethnicity
A 2x6x8 is used for a project. You cut 65 5/8" off for the project. What is the length of the leftover scrap piece?
57 5/8"
26 7/8"
32 1/8"
30 3/8"
A productive employee (team member) always...
contributes ideas
expresses respect and support
does his/her share
all are correct
Detailed information regarding the possible hazards associated with a product is contained in the...
Welding Procedures Specification (WPS)
Safety Data Sheet (SDS)
Confined Space Entry Permit (CSEP)
Confined Space Entry Permit (CSEP)
Which of the following is the responsibility of OSHA?
making sure every individual wears safety glasses
restrict the use of asbestos or other harmful materials in the workplace
figure out the hospital cost associated with workplace injuries
determine career salaries
"Abrasive" is another term for sandpaper.
True
False
If you find a hazard like a loose or broken guard on a machine, you should_____.
Fix it and continue
Ignore it
Turn the machine off and let your Supervisor know
Use duct tape and cover it
Which of the following tool parts keep body parts from moving bits, belts, and blades?
Protective guards
Safety glasses
GFCI extension cord
All answers are CORRECT
Safety is the responsibility of...
Employee
Supervisor
CEO
EVERYONE
You cut a piece of pipe into four equal parts. If the pipe was 36 inches long, how long is each piece?
9 in
8 in
10 in
12 in
The __________ must be turned on in the shop whenever someone is using the wood shop.
radio
dust collector
water sprinklers
alarm
Avoid using compressed air to clean chips from machine tools because...
it does the job to quickly
flying chips can get blown into the machine itself causing damage
it can cause a dangerous mist
no answer provided is correct
On sawblades, TPI stands for...
Tracked Incremental Processing
Teeth Per Inch
Total Performance Indicator
Treated Power Indexing
Flammable or oily rags should be disposed of in a....
metal container with a lid
open trash can
plastic bin with a lid
pile on the floor
Which of the following MUST be reported to your Instructor/Supervisor?
only major injures
only incidents and minor injuries
only near misses and minor injuries
ALL answers provide are correct
Safety glasses are required in manufacturing, construction, and fabrication areas because...
eye injuries are easily prevented
they match the company dress code
older workers have vision problems
NO answer provided is correct
When using a bandsaw to make a curved cut in wood, the best thing the operator can do to prevent breaking the blade is to:
Back the wood out of a running cut if it gets stuck
Force the wood into the blade to keep a steady pace
Make several relief cuts before cutting tight curves
Turn the wood sharply while the blade is moving
The best eye protection when using a mini-lathe is:
face shield AND safety glasses
Before operating a machine tool, you should...
make sure guards are in place
think about what you are about to do
remove jewelry
ALL answers are correct
When drilling a hole in wood, the operator using a drill press should:
Use a claw hammer to start the hole
Use high speed and no lubricant
Use a slower speed and apply cutting fluid
Push down with full force to drill faster
When applying for a job, which is NOT acceptable to provide on a resume?
previous employer's contact info
list of certifications
short job-seeing objectives
family members contact info as a reference
What should you do if you notice a strange noise coming from a machine?
Ignore it and continue working
Report it at the end of the day
Turn off the machine and inform the instructor
Increase the speed to see if it stops
Which of the following is NOT a safe practice when using power tools?
Following the manufacturer's instructions
Keeping the work area clean
Using protective eyewear
Wearing loose clothing
What is the first step in performing a safety check on a machine?
Read the user manual
Turn on the machine
Inspect the safety guards
Check the sharpness of the blade
