Which of the following are NOT included in pressure compounding with the comparison from the velocity compounding?

If the pressure drops take place in the nozzles, which are located in a nozzle or diaphragm block ahead of the row of blades, it is being called?

Which of the following are shaped in such a way that the space through which the steam passes is smaller than that through which steam enters?

It refers to a steam is supplied to a set of fixed nozzles wherein the steam pressure falls and gains in velocity?

It refers to the blades shaped that the entrance to a row of blades is of the same approximate size and shape as the exit from the row of blades?

It refers to a steam passes through the fixed blading and gains in velocity, it then impinges upon the moving blades to give an impulsive effect?

What is the basic principle behind the operation of a steam turbine?

Which type of steam turbine is commonly used for low to medium power applications due to its simplicity and cost-effectiveness?

Which type of steam turbine is characterized by a single set of stationary nozzles and moving blades?

What is the primary function of the blades in a steam turbine?

Which of the following types of seal consist of annular rings machined on the shaft which ride in projections of the labyrinth packing strip?

It refers to permit axial adjustment of the turbine rotor of the steam turbine engine?

Which of the following type of coupling couplings consist of a flange provided with external claws running parallel to the shaft to which it is secured?

Which of the following a steel band fitted at the outer circumference of the blades for the following purposes to reinforce the entire blading assembly?

Which of the following is contains the turbine and protect the device component from external influence and damage and it may also support the bearings on which the shafts rest to provide rigidity to the shaft?

If this wire is passed through the mating hole in the blading about its mid length and crimped at each end, it is being called?

It refers to have two spur gears on flanges mounted on each shaft. Teeth on these gears are continually in mesh with corresponding internal gears machined on a sleeve?

It refers to a devices used in maneuvering or for minor changes in speed, varies the steam chest pressure for controlling the speeds of turbine?

It refers to a ring or series of ring fitted in a turbine shaft at high pressure end, the purpose of the dummy piston is to prevent the rotor from shifting longitudinally?

It refers to the power transmitting device and is used to transmit the rotational movement of the blades connected to it at one end via the rotor to the coupling?

It refers to be used to connect turbine and driven shafts for the following reasons to allow for differences in expansion?

Which of the following type consist of a number of coupling bolts secured to one half of the coupling; these bolts pass through rubber or leather bushing secured to the other half of the coupling?

Which of the following device used to minimize leakage of steam through the clearance provided between moving and stationary parts of turbine?

It refers to attached into the wheel of the shaft or to the enlarge portion of the shaft called drum?

Which of the following are designs in such a way as to produce maximum rotational energy by directing the flow of the steam along its surface?

Which of the following are frequently used to seal the diaphragms of an impulse turbine from the shaft, in which case they consist of only one ring?

It refers to main components of rankine cycle that supplied high pressure of feed water into the boiler for generation?

It refer to the enthalpy of wet steam at given pressure or temperature in rankine cycle?

Which of the following main components of the rankine cycle store exhaust steam from the expansion system of the turbine?

If the difference between the enthalpy of superheated vapor at given pressure and temperature minus the enthalpy of saturated wet steam at given pressure or temperature, it being called

It refers to the entropy of saturated liquid at .010 Mpa from table 2?

If the ratio of the difference between the turbine work out put and the pump  work divided by the heat added, it is being called?

Which of the following process if the high pressure liquid enters a boiler where it is heated at constant pressure by an external heat source to become a dry saturated vapour?

If the ratio of the difference between the turbine work out put and the pump  work divided by the heat added, it is being called? 

Which of the following process if the wet vapours enter a condenser where it is condensed at a constant pressure to become a saturated liquid?

It refers to a enthalpy of superheated vapor at given pressure or temperature of rankine cycle?

Which of the following refers to a cycle is an idealized thermodynamic cycle of a heat engine that converts heat into mechanical work?

It refers to an intricate array of alternate stationary and rotating aero foil-section blades?

Which of the typically made up of a ring of fuel injectors that inject a steady stream of fuel into combustion chambers where it mixes with the air?

It refers to draws air into the engine, pressurizes it, and feeds it to the combustion chamber at speeds of hundreds of miles per hour?

Which of the following device or machine used to convert superheated steam to de-superheated mounted on rankine cycle process?

Which of the following components used into energy of steam and convert into electrical energy?

Which of the following refer to work out of the pump express the unit of kj/kg?

If the ratio of the difference between the turbine work out put and the pump  work divided by the heat added, it is being called? 

It refers to a machine or equipment used to convert low pressure of fresh water to high pressure and supplies to the boiler in rankine cycle process?

If the working fluid is pumped from low to high pressure. As the fluid is a liquid at this stage the pump requires little input energy, it refers to?

It refers to work output of turbine express in unit of kj/kg in rankine cycle?

Which of the following type of bearing is similar to shaft bearings used on reciprocating engines, are used only on small turbines?

Which of the following is consists of the turbine shaft and the attached moving blade and the absorb energy from working fluid (steam, gas, water etc) and converts that energy into mechanical energy?

Which of the following type of bearing must absorb a much greater amount of end thrust?

It refers to a type of seal that consist of a centrifugal pump runner secured to the turbine shaft and rotating in a chamber which is machined into the turbine casing?

Which of the following where the blades are shaped in such a way that the space through which the steam passes is smaller than that through which steam enters?

What effect does an increase in steam pressure have on the efficiency of a steam turbine?

Which of the following device use to prevent leakage of high-pressure steam to the atmosphere and of air, into the low pressure side?

If the alternate row of fixed and moving blades attached to the casing and the rotor respectively, form passageways which serve fixed and free nozzle, these being called?

It refers to a term applied only to impulse turbines which the stage is consists of two or more rows of moving impulse blades separated by rows of stationary blades?

Which of the following blades are secured to the casing; the moving blades, to a wheel; and a bank of nozzles directs steam against the first row of moving blades?

Which of the following types of engine in which the mechanical device extracts thermal energy from pressurized steam, and converts it into rotary motion?

Which of the following listed below is NOT included for the disadvantages of a turbine?

If the pressure drops take place in the nozzles, which are located in a nozzle or diaphragm block ahead of the row of blades, it is being called?

It refers to a steam is supplied to a set of fixed nozzles wherein the steam pressure falls and gains in velocity?

Which of the following is NOT belongs on velocity compounding with the comparison into the pressure compounding?

It refers to the dry saturated vapor expands through a turbine, generating power. This decreases the temperature and pressure of the vapour?

If the ratio of the difference between the turbine work out put and the pump  work divided by the heat added, it is being called?

It refers to a machine or equipment used to convert low pressure of fresh water to high pressure and supplies to the boiler in rankine cycle process?

It refers to the entropy of saturated liquid at .010 Mpa from table 2?

If the working fluid is pumped from low to high pressure. As the fluid is a liquid at this stage the pump requires little input energy, it refers to?

Which of the following main components of the rankine cycle store exhaust steam from the expansion system of the turbine?

It refer to the enthalpy of wet steam at given pressure or temperature in rankine cycle?

It refers to main components of rankine cycle that supplied high pressure of feed water into the boiler for generation?

It refers to work output of turbine express in unit of kj/kg in rankine cycle?

Which of the following process if the high pressure liquid enters a boiler where it is heated at constant pressure by an external heat source to become a dry saturated vapour?