NEW
Font size
Worksheetsprop
Total questions: 35
Worksheet time: 18mins
With the propeller control switch in normal governing, what components maintain constant RPM?
Pulse generator, governor and synchrophaser
Synchrophaser, pulse generator and tach generator and governor
Speed bias motor, synchrophaser, pulse generator
Synchrophaser, speed bias motor and tach generator
What is the fuel governor check switches used to operationally check?
The pitchlock
Reverse torque
Servicing check
Rigging and adjustments
What is the difference between anti-icing and de-icing?
There is no difference
Anti-icing removes ice, while de-icing prevents ice
De-icing prevents ice and removes ice
Anti-icing prevents ice, while de-icing removesice
What unit sends the engine speed signal to the propeller synchrophaser ?
Pulse generator
Tach generator
Propeller governor
Tachometer indicator
Where are the control switches for the anti-icing and de-icing system located?
Co-pilot's side shelf panel
Pneumatic overhead panel
Throttle quadrant
Electrical overhead panel
When the propeller low warning light will come "ON" when the oil level is ?
8 quarts low
6 quarts low
4 quarts low
2 quarts low
What is the purpose of the fuel governorcheck switches?
Limit engine speed to 109%
Reset speeder spring tension to 106%
Set the fuel governor control for low speed ground idle
Limit the slave engine to a 2% drop in the event of master engine failure
When the ice detection system is inoperative, the propeller can be de-ic by placing the master switch to?
Off
Auto
Reste
Manual
What is the operating cycle foreach cycle for each propeller de-icing?
60 seconds ON, 30 seconds OFF
60 seconds ON, 60 seconds OFF
45 seconds ON, 15 seconds OFF
15 seconds ON, 45 seconds OFF
When the fuel governor check switch is used while performing?
Servicing check
Rigging adjustments
Pitch lock operational checks
Mastertrim box operational checks
What is the voltage that operates the heaters in the anti-icing system?
28 VDC
28 VAC
75 VDC
115 VAC
Where is the synchrophaser box located ?
In copilot side shelf
In Pilot side shelf
Under deck racK
Inside the front panel
Where is the propeller brake located?
At engine shaft
At the barrel assembly
In the reduction gear
In the control assembly
Where is the throttle beta switch located?
Throttle quadrant
Valve housing
Pump housing
Condition lever quadrant
Where is the magnetic pickup coil of the pulse generator located?
Valve housing
Pump housing
De-icercontactring
On the #1 blade
What are the positions on the anti-ice master switch?
Auto, off, on
Manual, auto, off
Reset, auto, manual
Reset, locked, on
What is the purpose of the air start position of the condition lever?
Unfeathering, servicing and ground checkout
Connect the synchrophaser in the beta range of operation
Allows the propellerto be stopped
Allows the propellerto be feathered
What system prevents the propeller from driving the engine?
Negative torque
Pulse generator
Synhcrophaser
Speed bias motor
How does the fire emergency feather the prop?
Electrically
Hydraulically
Mechanically
Mechanically and electrically
Where is the speed bias motor located in?
Valve housing
Pump housing
Engine
Synchrophase
What is the purpose of the synchrophazer ?
To increase noise and vibration
To adjust the propeller noise
To reduce noise and vibration
To help propeller speed
Where is the resynchrophaser switch located?
Throttle quadrant
Copilots side panel
Aft-end of the overhead panel
Electrical control and equipment
How many Prop. Governor control switch positions are there on the C-130 ?
6
3
2
1
What is used to select mechanical or normal mode of operation of prop
Mode select switch
Prop governor switch
Resynch switch
Mastertrim switch
Where the condition leveris placed to unfeather the propeller?
Run
Feather
Air start
Ground stop
What prevents engine RPM from exceeding 104%?
the fuel governor
the valv housing
To reduce noise and vibration
To help propeller speed
Where is the throttle beta switch located?
In the Dome Assy
In the valve housing
in the pump housing
in the throttle quadrant
Where is the N.T.S bracketlocated?
in the gearbox
in the valve huosing
in the grund position
in the flight position
Where can you adjust the blade angle?
in the valve huosing
Prop governor switch
in the dom assymply
in the pump huosing
Which shaft you pin when removing control from propeller?
beta shaft
alpha shaft
engine shaft
feathershaft
Where is the throttle anticipation located?
On the shaft
In the pump housing
In the barrel assembly
In the valve housing
What is the operating voltage of anti-icing system?
115 ACand 28 DC
95 AC and 24 DC M
95 AC and 24 DC C
120 AC and 40 DCElectrical control and equipment
Where is the master low oil light located?
Co-pilots side panel
Pilots instrument panel
Engine instrument panel
Co-pilots instrument panel
Where is the location of the main circuit breaker for de-icing and Anti-ic
resynch switch
in the Pilot isterement sid
over head panel
in the copilot rigth side
What is the purpose of the propeller?
lift the aircraft
drive the engine
control the engine
change the engine power to thrust
