Worksheetsrec 107 week 6 quiz
Total questions: 27
Worksheet time: 14mins
When replacing an intermediate aluminum sidewall panel
it is not necessary to remove all panels below
specialized tools are required
the vehicle must be raised, blocked, and leveled
a new panel must be glued into place
When mounting a replacement exterior aluminum panel, it must
be butted tightly into the seam
have a 1/16 to 1/8 seam gap
be mounted at the bottom edge of seam
be inserted no more than 1/4 into seam
what is pictured
L molding
corner molding
J molding
insert molding
When installing Vertical trim molding, the one sealant type that would NEVER be used is
exterior grade tube seal
self-leveling sealer
Butyl tape
silicone caulking
Installation of plastic or fiberglass components may require the use of
pilot holes
sticky-back tape
washer-head fasteners
self-tapping screws
When repairing a large gouge in a flat fiberglass panel, the technician typically uses
polyester body filler, sand and finish
fiberglass mat, resin, fill and finish
ABS cement
a fiberglass welding kit
Damaged fiberglass components should
always be replaced
be replaced with plastic parts
be completely re-fabricated and painted
be repaired if not exceeding the cost of replacement
When repairing a fiberglass cap, it is always necessary to
paint the entire cap
remove the entire cap
remove all appurtenances of the cap
check the cap for stress cracks to surrounding areas caused by the damage
Rear fiberglass caps mounted on inner back wall are
made of fiberglass or ABS plastic and mostly cosmetic
molded fiberglass and glued to the plastic support post
installed to add stability and strength to the unit
fastened to the roof through laminated panel
The inner back wall is generally
a laminated panel which can be repaired or rebuilt
made of aluminum bonded material and can only be replaced
held in position with steel dowel rods
repaired with fiberglass welding kit
When there is damage to the rear end trim of RV's
only the affected trim pieces need to be replaced
the entire rear end trim must be replaced
the trim can be repaired with silicone and gray tape
The wiring for the head lights is often damaged and will need repair
the picture is of
slide-out seals
slide out fascia
slide out railing
slide out block extension
The purpose of slide-out molding is to do all of the following EXCEPT
finish the appearance of the room and the sidewall opening
cover and protect wall corners and seal the room and sidewall
to keep the tires contained under an RV in case of blowout
clear debris from the room as it slides into its closed travel position
Which maintenance is required of molding and trims
petroleum-based lubrication
apply sealant
abrasive cleaners
enamel based cleaner
When replacing molding and trim on a travel trailer, always
reuse original sealant if it looks to be in good condition
remove old sealant, clean and replace with new
always relace corner blocks
replace the anti-wick seal
In order to obtain a replacement entry door, the technician must
have the VIN number
identify the vendor of the original door
measure the rough opening in the vehicle sidewall
identify the hinge location
To eliminate visible fasteners on the outside of the door, compartment doors can also be mounted
through the jamb with screws into the wall
using epoxy
vertically
using double sided tape
What is NOT required criteria of a secondary emergency escape
red handles
exit sticker
window style
size of opening
Weep holes are a component of a
propane container door
window
roof vent
bay door
Which of the following appliances in an RV do NOT require exterior venting
absorption refrigerator
forced air furnace
microwave/convection
water heater
Exterior vents (i.e. propane burning appliances) must be sealed in order to prevent
air leaks
water loss
heat loss
mold
Whenever an exterior lamp is repaired or replaced, what other areas should be inspected and checked for proper operation
entire DC electrical system
circuit wiring and switching
battery bank
alternator output
When replacing exterior lamps, what color of lamps are mounted to the rear for directional marketing
red lamps
yellow lamps
clear lamps
green lamps
A key factor in awning repair or replacement is
the color
the brand
the mounting
the method of deployment
After installing a slide topper awning, the top of slide room does not extend and seal properly due to
excessive tension on awning spring
incorrect size awning installed
incorrect brand of awning installed
lack of tension of awning spring
When replacing powered driver's mirrors, all of the following features should be checked EXCEPT
remote adjustment
deicing heaters
reflectivity
turn indicators
When replacing exterior lamps, what color of lamps are mounted to the front for directional marking
red lamps
amber lamps
clear lamps
green lamps
