WorksheetsSummer Quiz 809 TD
Total questions: 68
Worksheet time: 34mins
Name
Class
Date
1.
What is a hot strip heater primarily used for?
a)
Shaping and bending plastic
b)
Drilling holes
c)
Cutting wood
d)
Sanding surfaces
2.
Which safety equipment should you wear when using a band facer?
a)
Gloves
b)
Ear protection
c)
Goggles
d)
Safety harness
3.
When using a pillar drill, what must you always do before starting?
a)
Select the correct drill bit
b)
Turn off safety guards
c)
Remove all clamps
d)
Increase speed
4.
What is the main use of a screwdriver?
a)
To measure angles
b)
To tighten or loosen screws
c)
To cut through metal
d)
To mix paint
5.
Which tool is used to smooth out surfaces of wood and plastic?
a)
Hammer
b)
Chisel
c)
Band facer
d)
Saw
6.
How should materials be secured when using a pillar drill?
a)
With your hand
b)
With a clamp
c)
Loosely on the table
d)
With adhesive
7.
What is the risk of not using a guard on a band facer?
a)
There is no risk
b)
Increased accuracy
c)
Decreased efficiency
d)
Injury from flying debris
8.
What should you check before using a hot strip heater?
a)
The material compatibility
b)
The colour of the machine
c)
The length of the cord
d)
The warranty period
9.
How can you prevent injury when using a band facer?
a)
Work without any distractions
b)
Use the machine at its highest speed
c)
Ignore safety warnings
d)
Leave guards in place
10.
What type of drill bit should be used in a pillar drill for metal?
a)
Wood bit
b)
Spade bit
c)
Masonry bit
d)
HSS bit
11.
Identify this tool
a)
Tenon saw
b)
Coping saw
c)
Band facer
d)
Hot strip heater
12.
Identify this tool
a)
Flat file
b)
Steel ruler
c)
Carpenters Ruler
d)
Measuring Tape
13.
Identify this tool
a)
Scriber
b)
Centre punch
c)
Ball pein hammer
d)
Flat file
14.
Identify this tool
a)
Band facer
b)
Hot strip heater
c)
Coping saw
d)
Tenon saw
15.
Identify this tool
a)
Steel ruler
b)
Try square
c)
Scriber
d)
Centre punch
16.
Identify this tool
a)
Pillar drill
b)
Ball pein hammer
c)
Tenon saw
d)
Coping saw
17.
Identify this tool
a)
Polishing Machine
b)
Vacuum Former
c)
Bandfacer
d)
Hot strip heater
18.
Identify this tool
a)
Marking Gauge
b)
Centre punch
c)
Nail
d)
Scriber
19.
Identify this tool
a)
Coping Saw
b)
Tenon Saw
c)
Mitre Saw
d)
Hack Saw
20.
Identify this Sign
a)
Toxic
b)
Electricity
c)
Explosive
d)
Flammable
21.
Identify this Sign
a)
No food or drink
b)
Acute Toxicity
c)
Corrosive
d)
Hazardous to the environment
22.
Identify this Sign
a)
Corrosive
b)
Gas under pressure
c)
Explosive
d)
Electrical
23.
Identify this Sign
a)
Emergency Stop
b)
Do not touch
c)
Acute Toxicity
d)
First Aid Kit
24.
Identify this Sign
a)
Do not look directly at laser
b)
Tie hair back
c)
Wear Welding Mask
d)
Wear Goggles
25.
Why is Brass listed as Non-Ferrous & Alloy?
a)
It is made from copper and zinc.
b)
It is a type of plastic.
c)
It is a type of wood.
d)
It is a ferrous metal.
26.
What type of wood is Mahogany?
a)
Hardwood
b)
Softwood
c)
Manufactured board
d)
Thermoplastic
27.
What's the main difference between Ferrous & Nonferrous metals?
a)
Ferrous metals contain iron.
b)
Ferrous metals do not contain iron.
c)
Nonferrous metals are magnetic.
d)
Nonferrous metals are not recyclable.
28.
Which plastic stays set when it is moulded?
a)
Thermoset
b)
Thermoplastic
c)
Polystyrene
d)
Acrylic
29.
How are manufactured boards produced?
a)
By pressing and gluing wood layers.
b)
By growing naturally.
c)
By melting and molding plastics.
d)
By extracting from mines.
30.
Brass is an alloy of which two metals?
a)
Copper and Zinc
b)
Copper and Tin
c)
Iron and Carbon
d)
Aluminium and Magnesium
31.
Explain the meaning of malleability.
a)
The ability to be reshaped without breaking.
b)
The ability to conduct electricity.
c)
The ability to resist rust.
d)
The ability to float on water.
32.
What two materials make up steel?
a)
Iron and Carbon
b)
Copper and Zinc
c)
Aluminium and Silicon
d)
Tin and Lead
33.
What two properties are added when carbon and iron are mixed to make steel?
a)
Toughness and tensile strength
b)
Flexibility and softness
c)
Brittleness and conductivity
d)
Hardness and weight
34.
Why is safety important in the workshop?
a)
To keep everyone safe from accidents.
b)
To complete tasks faster.
c)
To reduce costs.
d)
To impress the teacher.
35.
What must you wear for protection in the workshop?
a)
Apron and goggles
b)
Sunglasses
c)
Sandals
d)
Hat and scarf
36.
What colour are mandatory signs?
a)
Blue
b)
Red
c)
Green
d)
Yellow
37.
What do prohibition signs indicate?
a)
Actions that must not be done
b)
Actions that must be done
c)
Areas that are safe
d)
Emergency exits
38.
Which plastic is used for making water taps and lamps due to its properties?
a)
Melamine
b)
Polystyrene
c)
Brass
d)
Polyethylene
39.
What is smog composed of?
a)
Smoke, gases, and moisture
b)
Water vapor and oxygen
c)
Dust and sand
d)
Car exhaust and sunlight
40.
What is a more eco-friendly way to get around compared to cars?
a)
Bicycles
b)
Motorcycles
c)
Airplanes
d)
Personal helicopters
41.
What should you do if you are unsure about using a machine in the workshop?
a)
Ask the teacher
b)
Use it anyway
c)
Ask a classmate
d)
Look it up online
42.
Why should you not distract a person using a machine?
a)
It is a safety hazard.
b)
They might get angry.
c)
It is rude.
d)
They might lose their concentration.
43.
What should you do in the event of an accident in the workshop?
a)
Report it immediately
b)
Keep it a secret
c)
Try to fix it yourself
d)
Ignore it
44.
What does 'SMART' stand for in the technology and design department rules?
a)
Safety, Management, Attitude, Respect, Tidiness
b)
Safety, Make sure, Always try, Respect, Tidy up
c)
Smartness, Maturity, Alertness, Readiness, Tidiness
d)
Sensible, Mature, Alert, Ready, Tidy
45.
What are the three different types of materials used in Technology?
a)
Wood, Plastic, Metal
b)
Paper, Cloth, Glass
c)
Leather, Rubber, Stone
d)
Clay, Sand, Cement
46.
What are most plastics made from?
a)
Oil
b)
Wood
c)
Metal
d)
Stone
47.
What is a thermoplastic?
a)
A plastic that can be reheated and reshaped.
b)
A plastic that cannot be reshaped after molding.
c)
A type of metal.
d)
A type of wood.
48.
What is a thermosetting plastic?
a)
A plastic that sets permanently after molding.
b)
A plastic that can be reheated and reshaped.
c)
A type of fabric.
d)
A type of glass.
49.
Which plastic is an example of a thermosetting plastic?
a)
Melamine Formaldehyde
b)
Polystyrene
c)
Polyethylene
d)
Nylon
50.
Name a product made from Melamine Formaldehyde.
a)
Electrical insulation
b)
Water bottles
c)
Window frames
d)
Food containers
51.
What are two ways that thermoplastics can be shaped?
a)
Melting and molding
b)
Cutting and gluing
c)
Bending and heating
d)
Pressing and painting
52.
Why are plastics harmful to our environment?
a)
They take a long time to decompose.
b)
They decompose quickly.
c)
They release oxygen.
d)
They are good for wildlife.
53.
Which tool is used to mark out metal?
a)
Scriber
b)
Pencil
c)
Chisel
d)
Saw
54.
What tool is used for smoothing plastic?
a)
Hand file
b)
Hammer
c)
Screwdriver
d)
Wrench
55.
What does a pillar drill do?
a)
Drill holes
b)
Cut wood
c)
Shape metal
d)
Paint surfaces
56.
What is the first step before using a machine?
a)
Asking for permission
b)
Turning it on
c)
Reading a book
d)
Watching TV
57.
Why is it important to use a template when shaping metal?
a)
To ensure accuracy
b)
To save time
c)
To impress others
d)
To waste materials
58.
Why should you use the strip heater for shaping plastic?
a)
To make it flexible
b)
To cool it down
c)
To change its colour
d)
To harden it
59.
Which plastic is known for its use in musical instruments due to its acoustic properties?
a)
Nylon
b)
Acrylic
c)
Polyethylene
d)
Brass
60.
What is the property of a material that allows it to be reshaped easily called?
a)
Malleability
b)
Conductivity
c)
Hardness
d)
Brittleness
61.
What is the purpose of an apron in the workshop?
a)
To protect your clothes
b)
To look professional
c)
To keep you warm
d)
To show rank
62.
What is a try square used for?
a)
Marking out wood
b)
Cutting wood
c)
Measuring angles
d)
Drilling holes
63.
What is the main use of plywood in manufacturing?
a)
Strengthening structures
b)
Creating flexible shapes
c)
Insulating heat
d)
Conducting electricity
64.
Why is MDF often used in furniture making?
a)
It is strong and cheap.
b)
It is very expensive.
c)
It has a natural grain.
d)
It is difficult to shape.
65.
What is the main benefit of recycling plastic?
a)
Saves resources
b)
Increases pollution
c)
Produces more waste
d)
Reduces job opportunities
66.
What is the significance of using renewable resources?
a)
They are unlimited.
b)
They are cheaper.
c)
They deplete quickly.
d)
They are non-recyclable.
67.
What is resistance measured in?
a)
Amps
b)
Ohms
c)
Volts
d)
millimetres
68.
Click the correct statement
a)
LEDs are brittle
b)
LEDs are energy efficient
c)
LEDs only come in one colour
d)
LEDs are hot to touch
100 %