Font size
WorksheetsAEU Knowledge Check
Total questions: 13
Worksheet time: 26mins
What is the length of the CCM Address Extension Unit - AEU (ATU-PVT-SBM1)?
690 mm
310 mm
500 mm
1000 mm
800 mm
How many CCM units does the AEU (ATU-PVT-SBM1) count for power supply calculation?
5 units
3 units
4 units
1 unit
2 units
Which units can be installed downstream of AEU (ATU-PVT-SBM1)?
Choose all that apply.
ATU-PVT-TT
ATU-PVT-LC (03, 05, 07, 10)
ATU-PVT-SBM1
ATU-PVT-LBF05
ATU-PVT-AOB
What are the benefits of using the AEU (ATU-PVT-SBM1) in a CCM Solution?
Choose all that apply.
Fast rerun before storing or sending out the rack
Optimized distribution of rack among mirrored systems
Creation of a rack-position link sent to middleware
Increase the number of possible primary targets (analyzers) reached by the rack
More efficient add-on testing as recursive flowMore efficient add-on testing as recursive flow
What happens when ALL 5 sample tubes AND rack barcodes cannot be identified?
Independent from the AEU settings, it will always trigger a STOP alarm
It will always send the rack to the configured default destination
Rack will be sent to the upstream unit connected to AEU
Rack will be forwarded to the same path as received from upstream CCM unit
Depending on the AEU settings, it can either display a STOP alarm or forward the rack to the configured default destination
What is the purpose of the barcode labels brackets located on the pull-in conveyor of AEU (ATU-PVT-SBM1)?
To inform the rack ID
To detect / inform, if the specific rack position is empty or occupied by sample tube
To inform the sample ID
To adjust the rack ID barcode reader
To adjust the sample ID barcode reader
Which functionalities apply to the AEU (ATU-PVT-SBM1)?
Choose all that apply.
Rack barcode identification
Communication to middleware
Assignment of new path to racks
Communication to analyzer
Availability of path (rack-jam/RTR signal) is sent to middleware
Which procedure must be performed after replacing the rack ID barcode reader with a new one?
Choose all that apply.
Self-driven BCR reading stop position adjustment
Configuration of the readable barcode types
Rack ID reading position adjustment
Rack ID BCR initial setting
Self-driven BCR reading start position adjustment
What is the jumper setting for JP610 on the drive board UN201 to "bridge" the sensor of the protective cover during the adjustment procedure?
JP610 to 2-3 short
JP610 to 1-2 short
JP610 3-4 short
What is the expected time for AEU to receive the "Respond Path Message" from middleware?
10 ms
7 s
30 ms
10 s
12 s
Is the timeout to receive the "Respond Path Message" of the AEU configurable?
No
Yes
Depends on the AEU mode (initial rack pairing or normal mode)
The offline button is activated on the AEU (ATU-PVT-SBM1). Which statements regarding the unit behavior are correct?
Choose all that apply.
If initial-rack pairing mode is configured, rack will be forwarded to the configured default destination address
If normal mode is configured, rack will remain on the AEU
If initial-rack pairing mode is configured, rack will be forwarded to the same path received from the upstream unit
If initial rack pairing mode is configured, the rack will remain on AEU
If normal mode is configured, rack will be forwarded to the configured default destination address
What kind of information is exchanged between the AEU (ATU-PVT-SBM1) and the middleware?
Choose all that apply.
Patient specific data (name, age, tests, etc)
Rack ID and sample ID
Sample tube position on rack
Path availability (rack-jam / RTR signal) from downstream units of AEU
New destination (path number) assigned to the rack
