wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

Aircraft 123

Total questions: 22

Worksheet time: 11mins

Name
Class
Date
1.

What does the backup generator converter do?

a)

Changes variable voltage into 115V/400H2

b)

Converts DC power to AC

c)

Changes variable frequency into 115V/400H2

2.

Which power management panel gets power from the hot battery bus?

a)

P300 APU auxiliary panel

b)

P10O power panel

c)

P310 standby power panel

3.

Which unit controls the no-breaks power transfer?

a)

Bus power control unit (BPCU)

b)

Backup converter

c)

Generator control unit (GCU)

4.

With AC power on the airplane, what happens when you place the standby power switch to the BAT position?

a)

The static inverter comes on and powers the standby AC bus

b)

A DC/standby self check starts

c)

Nothing will happen

5.

On which version of the 777 will you find the P330 panel?

a)

All versions

b)

200/300

c)

Freighter

6.

Which of the following statements is true?

a)

The 777 line replaceable units (LRUs) and line replaceable modules (LRMs) use different databuses

b)

The 777 line replaceable units (LRUs) and line replaceable modules (LRMs) use the same databuses

c)

The 777 line replaceable units (LRUs) and line replaceable modules (LRMs) do not use databuses

7.

Pneumatic bleed air is supplied by:

a)

APU only

b)

2 stages of the low pressure compressor

c)

2 stages of the high pressure compressor

8.

Empennage and body section 48 located at zone:

a)

300

b)

500

c)

400

9.

Where is engine fire extinguisher bottle located?

a)

Engine pylon

b)

Fwd cargo bay

c)

Landing gear wheel well

10.

How is a fire in the lavatory waste compartment indicated?

a)

By red discharge indicator disk.

b)

By warning light on the flight deck

c)

By temperature-indicator

11.

Where is the forward cargo door manual latch drive located?

a)

On the fuselage, forward of the door

b)

Upper forward corner of the door

c)

In the lock handle housing

12.

Which parts of the rudder are NOT made from composite materials?

a)

Rudder tab

b)

Rudder hinge

c)

Front and rear spar.

13.

What determines the grip length of the spring clips which secure the passenger compartment windows?

a)

The number of the windows installed

b)

The location in the fuselage

c)

The size of the window

14.

What type of door is the forward large cargo door?

a)

Plug type-door

b)

Non-plug type door

c)

A hinged door.

15.

The leading edge, trailing edge and wing tip are all part of the wing:

a)

Secondary structure

b)

Primary structure

c)

Flight control surfaces

16.

The inspection method which uses a liquid to detect cracks is called:

a)

X-ray inspection

b)

Magnetic particle

c)

Penetrant inspection

17.

Which of the following inspection methods requires only basic tools and materials, such as a mirror and magnifying glass?

a)

Detailed inspection.

b)

Penetrant inspection

c)

Special detailed inspection.

18.

During an engine start on ground with air conditioning pack operating, the pack switch OFF light was observed to stay on for about 2 minutes. It means:

a)

This is normal because the packs stay off for 2 minutes to allow time to start the engines

b)

The related air conditioning system is faulty as the OFF light should not be illuminated

c)

The related pack flow valve is suspected to be sluggish in operation

19.

What percent of the total air outflow goes out through the forward and aft outflow valves when you set the two outflow valves to the automatic mode, usual position of the valves?

a)

20% and 80%

b)

80% and 20%

c)

50% and 50%

20.

When will the pack operate in backup mode?

a)

When switched to backup mode from the cockpit

b)

When one pack fails during ground operation

c)

When only battery power or standby power is available

21.

What type of air cycle machine is used on the B 777?

a)

Twin compressor and twin turbine

b)

Single compressor and twin turbine

c)

Single compressor and single turbine

22.

What does the flow sensor measure?

a)

Duct pressure and temperature

b)

Pack inlet pressure and inlet differential pressure

c)

Pack outlet pressure and temperature