WorksheetsIMI G0102k Health and Safety Quiz
Total questions: 44
Worksheet time: 22mins
Name two of your responsibilities under the Health and Safety at Work Act 1974.
Take care of machine guards and report any problems.
Ignore health and safety policies.
Damage machinery for fun.
Avoid using PPE at all times.
What is COSHH and what does it relate to?
Control of Substances Hazardous to Health Regulations 2002
Control of Safe Handling of Heavy Equipment
Control of Safety and Health Hazards
Control of Substances and Hazardous Materials
Name three workshop activities that could potentially pollute your environment.
Incorrect disposal of an oil filter
Proper recycling of waste
Correct disposal of antifreeze
Using eco-friendly materials
What is PPE and when should you use it?
Personal protective equipment, used to protect from accidents
Public protective equipment, used for public events
Personal prevention equipment, used for preventing theft
Public prevention equipment, used for public safety
What does PUWER refer to? Name one employer responsibility under this regulation.
Provision and Use of Work Equipment Regulations 1998
Provision and Use of Workplace Environment Regulations
Provision and Use of Work Energy Resources
Provision and Use of Work Efficiency Regulations
What is a prohibition notice and who issues it?
A notice to stop work immediately due to safety risks, issued by the Health and Safety Executive Inspectorate/Inspector.
A notice to increase work hours, issued by the employer.
A notice to change work procedures, issued by the team leader.
A notice to hire more staff, issued by the HR department.
When should you wear approved safety glasses?
Only when working with chemicals.
Whenever there is danger to the eyes, such as sanding or working at height.
Only during welding.
Only when working outdoors.
Why are latex gloves used?
To keep hands warm.
To prevent grease, oil, and dirt from entering the skin.
To improve grip on tools.
To protect against electrical shocks.
What type of mask must you use when replacing brake linings?
A surgical mask.
A dust particle mask.
A gas mask.
A cloth mask.
What three types of vehicle protective equipment (VPE) must you use when working inside a vehicle?
Helmet, gloves, and boots.
Foot mat cover, steering wheel cover, and seat cover.
Safety glasses, earplugs, and respirator.
Apron, face shield, and knee pads.
What is the difference between a hazard and a risk?
Hazard is a potential cause of harm; risk is the likelihood of harm being realized.
Hazard is a certain cause of harm; risk is the prevention of harm.
Hazard is the likelihood of harm; risk is the potential cause of harm.
Hazard and risk are the same.
How should you dispose of waste oil and why?
Pour it down the drain to get rid of it quickly.
Burn it to eliminate waste.
Process and refine it to prevent environmental harm.
Store it indefinitely in containers.
Give examples of three different toxic substances used in a workshop.
Water, air, and sand.
Paints, fuels, and fumes from welding.
Wood, plastic, and rubber.
Soap, detergent, and vinegar.
Accidents are often caused by a mixture of factors. List three factors.
Human, occupational, and environmental
Mechanical, electrical, and chemical
Physical, biological, and chemical
Social, economic, and political
What type of fire extinguisher has a black label?
Water
Foam
CO₂ (carbon dioxide)
Dry powder
What is the meaning of flash point?
The highest temperature at which a liquid can ignite
The lowest temperature at which a liquid turns into a vapor to form an ignitable mixture in the air
The temperature at which a solid becomes a liquid
The point at which a gas becomes a liquid
What is the 1, 2, 3 system of risk assessment?
A method to categorize risks into low, medium, and high
A system to rate the severity and likelihood of injury on a scale of 1 to 3, then multiply for a risk rating
A process to evaluate risks based on past incidents
A checklist to ensure all safety measures are in place
What is a control measure?
A control measure is introduced when a hazard or risk is not adequately controlled.
A control measure is a type of warning sign.
A control measure is a method to increase electricity usage.
A control measure is a tool for vehicle maintenance.
What color are mandatory warning signs?
Blue
Red
Green
Yellow
Why do you need to turn off the light in a storeroom when it is not being used?
To save electricity
To increase brightness
To reduce noise
To improve air quality
What effect does the wasting of resources have on a business?
Increases bills and reduces profit
Decreases bills and increases profit
Has no effect on bills or profit
Improves employee satisfaction
What should you use to scrub your hands with when using a bench drill?
Soap and water
Hand sanitizer
Oil and water
Dry cloth
Name three sources of technical information used in the workshop.
Other staff, Service manual, Vehicle handbook
Newspapers, Magazines, Television
Social media, Blogs, Podcasts
Fiction books, Novels, Comics
Which of the following is a document a technician needs to use in the workshop?
Job cards
Blueprints
Warranty cards
Sales receipts
Why is customer authorization needed for additional work on a vehicle?
To ensure the customer is informed and agrees to the work
To increase the cost of the service
To avoid legal issues with the manufacturer
To speed up the repair process
Which of the following is an example of non-verbal communication?
Facial expressions
Telephone
Voicemail
What is a method of electronic communication?
Telephone
Hand gestures
Face-to-face conversation
Body posture
What is a barrier to communication?
Not listening
Clear instructions
Effective feedback
Active engagement
Which tool can measure inside diameter, outside diameter, and depth?
Vernier caliper
Ruler
Tape measure
Protractor
What is meant by the pitch of a hacksaw blade?
The width of the blade
The distance from the tip of one tooth to the tip of the next
The thickness of the blade
The length of the blade
What does the M signify on a M12 x 1.5 x 60 bolt?
Millimeter
Metric
Metal
Measurement
Which hammer should you use to avoid damaging components when dismantling?
Rubber mallet
Copper and hide hammer
Steel hammer
Wooden mallet
What should you do to ensure correct reassembly of a component before you dismantle it?
Use a screwdriver to mark components
Use a centre punch with a hammer to mark components
Use a marker pen to label components
Use a chisel to engrave components
What type of force is used to hold a component in a hand vice?
Tension
Compression
Shear
Torsion
Under the Provision and Use of Work Equipment Regulations (PUWER), who has the main responsibility for ensuring that all equipment supplied for use in the workshop is in safe working order?
Your employer
Trade union officials
You
The Health and Safety Executive inspector
What is the correct PPE to wear when charging a battery?
helmet, heat-resistant gloves, apron and overalls, safety boots
goggles, Kevlar gloves, overalls, safety boots
helmet, full face mask, ear defenders, latex gloves, apron, safety boots
goggles, chemical-resistant gloves, mask, overalls, apron, safety boots
Which of the following is the correct definition of a hazard?
something that has the potential to cause harm or damage
the likelihood of an accident happening
a serious accident resulting in an injury
an unexpected and unplanned event in the workplace
Which of the following types of fire extinguisher should not be used on fires involving flammable liquids?
cream label – foam
black label – carbon dioxide
blue label – powder
red label – water
The chemical name for poisonous vehicle exhaust fumes is:
carbon dioxide
carbon monoxide
epoxy resin
trichloroethylene
If there is a serious accident and the person is bleeding severely, the first action to take would be:
make them a cup of tea
apply pressure to the wound
put a plaster on the wound
apply a tourniquet
Which one of the following is the correct way of lifting a weight from the ground?
back bent, legs straight
back bent, knees on the ground
back straight, knees bent
back straight, legs straight
Some nuts are fitted with a nylon insert in order to:
allow the nut to be loosened easily
lubricate the thread as the nut is fitted
keep the tightened nut in place
protect the thread on the bolt
The most effective equipment for raising a vehicle a short distance from the ground is:
a pulley block
a winch
a hydraulic jack
a lifting chain
When a metal has become hard due to cold working, it can be changed to its softest state by:
annealing
tempering
nitriding
normalising
