wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

Ase Practice Engine Performance

Total questions: 16

Worksheet time: 16mins

Name
Class
Date
1.
A misfire is detected at the #3 cylinder of a COP ignition system. There is no power at the Bat+ terminal of the coil. Which of the following is the MOST likely cause of this condition?
a)
Resistance in the primary circuit
b)
An open between the coil and power source
c)
A leak in secondary insualation
d)
Resistance in the secondary circuit
2.
Technician A says a (TPI) throttle position sensor is a potentiometer that indicates throttle angle. Technician B says a throttle position sensor can be tested for resistance with an ohmmeter. Who is correct?
a)
Tech A
b)
Tech B
c)
Both
d)
Neither
3.

After performing a wet compression test, the pressure in each of the cylinders increased, but remained below specifications. Tech A says this is caused by incorrect valve timing. Tech B says this is caused by worn piston rings. Who is correct?

a)

TECH A

b)

TECH B

c)

BOTH A and B

d)

NEITHER

4.

A vacuum gauge is connected to a port on the intake manifold of an engine with poor performance. The needle on the gauge fluctuates between 15 ''hg and 20 ''hg vacuum at idle. This vacuum gauge reading indicates...

a)

a normal condition

b)

late ignition valve or timing

c)

a burned exhaust valve

d)

a restricted exhaust

5.

The PCM uses all of these inputs to calculate air flow ratio and speed control EXCEPT...

a)

An engine coolant temperature sensor (ECT

b)

An exhaust gas recirculation valve (EGR

c)

An intake air temperature sensor (AIT

d)

A throttle position sensor (TPS

6.

Two techs are discussing a turbocharged engine. Tech A says the wastegate is a component used to control boost pressure. Tech B says when opened, the wastegate diverts exhaust gas from the turbine wheel. Who is correct?

a)

Tech A

b)

Tech B

c)

Both A and B

d)

Neither

7.

Tech A says when the vacuum hose is disconnected from the vacuum operated fuel pressure regulator, fuel pressure should increase. Tech B says a restricted fuel return line will cause low fuel rail pressure. Who is correct?

a)

TECH A

b)

TECH B

c)

BOTH A AND B

d)

NEITHER

8.
The MAP sensor's vacuum hose is loose and cracking. Technician A says this sensor measures air mass to establish the fuel injector's base pulse width. Technician B says this sensor measures changes in intake manifold pressure. Who is correct?
a)
Tech A
b)
Tech B
c)
Both
d)
Neither
9.
A cylinder power balance test is being performed on a vehicle with sequential port fuel injection. Two adjacent cylinders are under performing. Technician A says this could be caused by a restriction in the fuel injectors. Technician B says this could be caused by leaking secondary insulation. Who is correct?
a)
Tech A
b)
Tech B
c)
Both A and B
d)
Neither A or B
10.
Technician A says the MAP sensor is located on the intake manifold and informs the PCM of intake manifold pressure. Technician B says the MAF sensor senses air flow in the air tube. It's signal indicates engine load to the PCM. Who is correct?
a)
Tech A
b)
Tech B
c)
Both A and B
d)
Neither A or B
11.
A vehicle has a check engine light with codes indicating a problem with the enhanced evaporative emission system and a rich fuel condition. Technician A says a defective evaporative purge valve will cause a rich air fuel ratio. Technician B says the tank pressure sensor will notify the PCM of excessive tank pressure. Who is correct?
a)
Tech A
b)
Tech B
c)
Both
d)
Neither
12.
A COP ignition system has no spark at any of the coils. Which of these is MOST likely causing this loss of spark?
a)
A faulty PCM driver
b)
Excess resistance in the primary circuit
c)
Excess resistance in the secondary circuit
d)
No power to PCM BAT+
13.

An engine does not reach operating temperature while being driven. Which of these could be the cause?

a)

A slipping water pump belt

b)

A stuck open thermostat

c)

A stuck closed thermostat

d)

A clogged radiator passage

14.

Which engine valve configuration has the camshaft in the cylinder block.

a)

Over Head Valve (OHV)

b)

Over Head Cam (OHC)

c)

Dual Over Head Cam (DOHC)

d)

This is a trick question Mr. Gregoire

15.

What are the two types of cooling systems:

a)

Air and Vent

b)

Vent and Electric

c)

Liquid and Electric

d)

Liquid and Air

16.

True or False: An engines cooling system is designed to transfer excess heat from the engine to the atmosphere.

a)

True

b)

False

Similar Resources on Wayground

U r mom ashley

13 questions

U r mom ashley

quiz

Worksheet

•

9th - 12th Grade

Interesting Bird Facts

11 questions

Interesting Bird Facts

quiz

Worksheet

•

KG - Professional Dev...

Indovina le proprietà del vetro

17 questions

Indovina le proprietà del vetro

quiz

Worksheet

•

6th Grade - University

Keyboard Shortcuts

18 questions

Keyboard Shortcuts

quiz

Worksheet

•

5th - 12th Grade

Google Workspace for Education

15 questions

Google Workspace for Education

quiz

Worksheet

•

10th - 12th Grade

Analog and Digital

20 questions

Analog and Digital

quiz

Worksheet

•

9th - 12th Grade

Medidas de almacenamiento

11 questions

Medidas de almacenamiento

quiz

Worksheet

•

11th Grade

Conecta IF

18 questions

Conecta IF

quiz

Worksheet

•

9th - 12th Grade