wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

monthly test december 2024

Total questions: 40

Worksheet time: 3600secs

Name
Class
Date
1.
Which of the following is not part of the disc brake system
a)
Brake rotor
b)
Brake caliper
c)
Brake Shoe
d)
Brake pad
2.
What does the acronym ABS stand for?
a)
All Brakes Stopping
b)
Awesome Braking System
c)
Anti-lock Braking System
d)
Advanced Braking System
3.

Select appropriate answer for the image given

a)

Drum Brake Part

b)

Disc Brake Part

4.

Select appropriate answer for the image given

a)

Drum Brake Part

b)

Disc Brake part

5.

Select appropriate answer for the image given

a)

Drum Brake Part

b)

Disc Brake Part

6.

Select appropriate answer for the image given

a)

Drum Brake Part

b)

Disc Brake Part

7.

What does the braking system use to reduce the speed of a vehicle?

a)

grease

b)

speed

c)

friction

d)

torque

8.
What is this part?
a)
Wheel stud
b)
Wheelcylinder
c)
Wheel bearing
d)
Starter
9.
What is this part?
a)
Pads
b)
Shoes
c)
Drums
d)
Rotors
10.
What is this part?
a)
Master cylinder
b)
Brake shoe
c)
Brake rotor
d)
Brake pump
11.

Diesel fuel, compared to petrol is

a)

less difficult to ignite

b)

just about the same difficult to ignite

c)

more difficult to ignite

d)

highly ignitable

12.

Which of the following is not an automobile?

a)

Motor cycle

b)

passenger car

c)

Aeroplane

d)

Truck

13.

What are the common signs that indicate a need for suspension and steering maintenance?

a)

Uneven tire wear, steering wheel vibration, vehicle pulling to one side, knocking or clunking noises when going over bumps, leaking fluid from the shocks or struts

b)

Strong smell of gasoline inside the car

c)

Dashboard lights flickering

d)

Excessive engine noise

14.

What are the key components of a typical suspension system?

a)

springs, shock absorbers (dampers), struts, control arms, and anti-roll bars

b)

tires, exhaust system, steering wheel

15.

How does the suspension system contribute to a smooth ride for the vehicle?

a)

The suspension system absorbs shocks and vibrations from the road, allowing the wheels to move up and down independently.

b)

The suspension system reduces the visibility for the driver by lowering the vehicle.

c)

The suspension system increases fuel consumption by adding weight to the vehicle.

d)

The suspension system emits loud noises that disrupt the smooth ride.

16.

What is the purpose of the anti-lock braking system (ABS)?

a)

To prevent wheel lock-up during hard braking

b)

To improve tire traction on wet roads

c)

To increase fuel efficiency

d)

To enhance engine performance

17.
What is the purpose of a steering system in a vehicle?
a)
To regulate the engine power
b)
To control the vehicle's direction
c)
To maintain tire pressure
d)
2
18.
Which of the following is a common type of steering system used in most vehicles?
a)
Rack and pinion
b)
Clutch system
c)
Brake system
d)
Suspension system
19.
Which component in a steering system enables the driver to turn the wheels?
a)
Steering wheel
b)
Drive belt
c)
Brake pads
d)
Shock absorbers
20.
Which type of steering system provides better feedback and control to the driver?
a)
Power steering
b)
Manual steering
c)
Electric steering
d)
Hydraulic steering
21.
What is the purpose of power steering in a vehicle?
a)
To increase the vehicle's top speed
b)
To decrease fuel consumption
c)
To reduce the effort required to steer
d)
To improve braking performance
22.
How does a rack and pinion steering system work?
a)
It uses hydraulic fluid to turn the wheels
b)
It uses gears to convert steering wheel rotation into linear motion
c)
It uses an electric motor to control steering effort
d)
It uses a belt and pulley system to steer the wheels
23.
Which steering component connects the steering gearbox to the wheels?
a)
Pitman arm
b)
Tie rod end
c)
Idler arm
d)
Steering knuckle
24.

State the type of gear shown in the picture.

a)

Bevel Gear

b)

Spur Gear

c)

Helical Gear

d)

Hearring Bone Gear

25.

Name the type of gear.

a)

Rack & Pinion Gear

b)

Spur Gear

c)

Helical Gear

d)

Hearring Bone Gear

26.

Name the type of gear.

a)

Bevel Gear

b)

Spur Gear

c)

Helical Gear

d)

Hearring Bone Gear

27.

____ gears are used to transfer drive on a 90 degrees angle.

a)

Bevel

b)

Rack and pinion

c)

Worm

d)

Compound

28.

A _______ is a wheel with teeth that meshes with another similar gear that is typically larger or smaller.

a)

gear

b)

tyre

c)

pulley

d)

rack and opinion

29.
What is the purpose of the tread on a tyre?
a)
To provide grip and traction
b)
To keep the wheel balanced
c)
To reduce air pressure
d)
To enhance the appearance
30.
What is the purpose of wheel balancing?
a)
To evenly distribute weight around the wheel and reduce vibrations
b)
To increase the speed of the vehicle
c)
To improve fuel efficiency
d)
To enhance cornering abilities
31.
What does the "R" stand for in tyre size designations such as 205/55R16?
a)
Reinforced
b)
Radial
c)
Round
d)
Rim
32.
What is the purpose of tyre rotation?
a)
To change the direction of the grooves on the tread
b)
To extend the lifespan of the tyres by promoting even wear
c)
To increase fuel efficiency
d)
To improve braking performance
33.
What is the purpose of tyre tread wear indicators?
a)
To indicate the tyre's speed rating
b)
To alert the driver when the tyre's tread has worn down to a dangerous level
c)
To provide decorative elements on the tyre surface
34.
Which type of tyre is best suited for off-road driving?
a)
Highway tyres
b)
Performance tyres
c)
All-terrain tyres
d)
Winter tyres
35.

The power actually developed inside the engine cylinder is called as

a)

Indicated power

b)

Brake power

c)

Frictional power

d)

None of these

36.

If the air-fuel mixture in a spark ignition engine is too rich, then air-fuel ratio is about

a)

17:1

b)

15:1

c)

13:1

d)

10:1

37.

In a Diesel engine, the function of a fuel injector is to

a)

Mix the fuel and air

b)

Ignite the air-fuel mixture

c)

 Provide flame front for ignition

d)

Spray atomized fuel in the cylinder

38.

The cam shaft in an engine is always mounted

a)

Parallel to the crankshaft

b)

Perpendicular to the crankshaft

c)

Inclined to the crankshaft

d)

None of these

39.

The sequence order of events in a four stroke engine is

a)

Suction exhaust power compression

b)

Suction power compression exhaust

c)

Suction compression power exhaust

d)

Exhaust compression power suction

40.

Which of the following is not a part of the chassis?

a)

Wheels

b)

Front axle

c)

Steering system

d)

Seats

Similar Resources on Wayground

3.2.1 - Teamwork in Engineering

40 questions

3.2.1 - Teamwork in Engineering

quiz

Worksheet

•

10th Grade - University

Basic Electricity Concepts

40 questions

Basic Electricity Concepts

quiz

Worksheet

•

9th Grade - University

IED - 2024

40 questions

IED - 2024

quiz

Worksheet

•

10th Grade - University

PKKR

35 questions

PKKR

quiz

Worksheet

•

12th Grade

ASAS Ganjil PSPTKR 12 2025/2026

40 questions

ASAS Ganjil PSPTKR 12 2025/2026

quiz

Worksheet

•

12th Grade

AutoCAD Certified User Practice Quiz 2

35 questions

AutoCAD Certified User Practice Quiz 2

quiz

Worksheet

•

11th Grade - University

SISTEM MEKANIKAL

40 questions

SISTEM MEKANIKAL

quiz

Worksheet

•

9th - 12th Grade