wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

Engineering Drawing - SG Academy

Total questions: 60

Worksheet time: 1hrs 10mins

Name
Class
Date
1.

APAKAH LUKISAN KEJURUTERAAN

a)

SENI HALUS

b)

LUKISAN MENGGUNAKAN KOMPUTER

c)

GAMBARAN LUKISAN DALAM BENTUK GRAFIK

2.

BERIKUT ALATAN PENTING UNTUK LUKISAN KEJURUTERAAN KECUALI

a)

DRAWING BOARD

b)

INTERNET

c)

SET SQUARE

3.

APAKAH STANDARD SIZE KERTAS LUKISAN UNTUK LUKISAN KEJURUTERAAN

a)

A4

b)

A3

c)

A1

4.
Define orthographic projection?
a)
Showing a front view, side view and plan view
b)
Showing a front and a back view
c)
First and third angle
d)
Showing views of a complex object
5.
What is the purpose of a title block?
a)
To show all the information that is needed to read the drawing
b)
To include names and units of measurements
c)
To show all the parts of the drawing
6.
Most commonly used type of paper for drawing
a)
Isometric
b)
Quarter inch
c)
Graph paper
d)

Plain paper

7.
A plan view is
a)
Looking over the top of a drawing
b)
Looking underneath of a drawing
c)
Looking at the side of a drawing
8.

What type of projection is shown on the right?

a)

Sketch

b)

Isometric

c)

Orthographic

d)

Oblique

9.

What angle(s) do you use to draw an Isometric drawing?

a)

30/60 degrees

b)

45 degrees

c)

90 degrees

d)

45/45 degrees

10.

What projection is this object drawn in?

a)

First Angle

b)

Third Angle

11.

What projection is this object drawn in?

a)

First Angle

b)

Third Angle

12.
Define orthographic projection?
a)
Showing a front view, side view and plan view
b)
Showing a front and a back view
c)
First and third angle
d)
Showing views of a complex object
13.
What is the purpose of a title block?
a)
To show all the information that is needed to read the drawing
b)
To include names and units of measurements
c)
To show all the parts of the drawing
14.

The drawing shown below is an example of what type of drawing?

a)

Orthographic

b)

P&ID

c)

Cutaway

d)

Isometric

15.

________is a means of representing a three-dimensional object in two dimensions.

a)

Projection

b)

Orthographic Project

c)

Isometric Project

d)

2D drawing

16.

Is the drawing shown orthographic projection or isometric projection?

a)

Orthographic

b)

Isometric

17.

Is the drawing shown orthographic projection or isometric projection?

a)

Orthographic

b)

Isometric

18.

Is the drawing shown orthographic projection or isometric projection?

a)

Orthographic

b)

Isometric

19.

Is the drawing shown orthographic projection or isometric projection?

a)

Orthographic

b)

Isometric

c)

Both

20.

Identify the items included in an engineering drawing title box.

a)

Drawing Title

b)

Drawing Number

c)

Site

d)

Signatures

e)

References

21.

Isometric projections presents a single view of the component commonly from above and at a 30 degree angle.

a)

True

b)

False

22.

What type of projection is shown on the right?

a)

Sketch

b)

Isometric

c)

Orthographic

d)

Oblique

23.

What is the correct term for this drawing type?

a)

Isometric

b)

3D

c)

Orthographic

d)

Oblique

24.

What does ISO stand for when looking at conventional drawings?

a)

Institute for Standards

b)

International Science Organisation

c)

International Standards Organisation

d)

Independent Standards Organisation

25.
Define orthographic projection?
a)
Showing a front view, side view and plan view
b)
Showing a front and a back view
c)
First and third angle
d)
Showing views of a complex object
26.

Identify the scale that reads 1 inch on the drawing = 100 ft. actual.

a)

100:1

b)

1:100

c)

10:1/2

d)

1/2:10

27.

Using the diagram below identify the component represented.

a)

Transformer

b)

Resistor

c)

Capacitor

d)

Transistor

28.

Using the diagram below identify the electrical component shown.

a)

Fuse

b)

Single Pole Switch

c)

Transformer

d)

Relay

29.

Using the diagram below identify the electronic component shown.

a)

Transistor

b)

Diode

c)

Fixed Resistor

d)

Amplifier

30.

Using the diagram below identify the electronic component shown.

a)

Diode

b)

Transistor

c)

Fixed Resistor

d)

Amplifier

31.

Nyatakan jenis pensil yang sesuai digunakan untuk garisan keratan

a)

H

b)

2H

c)

3H

d)

4H

32.

Apakah yang ditunjukkan oleh gambar?

a)

Blok tajuk

b)

Senarai objek

c)

Bilangan bahan

d)

Jadual pengubahsuaian

33.

Apakah jenis pensel yang digunakan untuk membuat garisan objek, menghuruf dan mengangka?

a)

B/H

b)

B

c)

H

d)

HB

34.

Berakah sisi oktagon sekata?

a)

6

b)

10

c)

8

d)

9

35.

Pentagon mempunyai berapa bilangan sisi?

a)

4

b)

5

c)

6

d)

7

36.

Apakah garisan lukisan teknik seperti dalam gambarajah

a)

Garisan Pusat

b)

Garisan Susur

c)

Garisan Tersembunyi

d)

Garisan Dimensi

37.

Apakah jenis garisan seperti dalam gambarajah?

a)

Garisan Tersembunyi

b)

Garisan Keratan

c)

Garisan Binaan/unjuran

d)

Garisan susur/sebenar

38.

Alat lukisan yang digunakan untuk melukis semua garis mendatar dan ufuk, menyokong peralatan lain untuk melukis garis sudut

a)

Set jangka lukis dan pembahagi

b)

Sesiku-T

c)

Sesiku Segitiga 60°, 30° dan Sesiku Segitiga Boleh Laras

d)

Template

39.

Alatan ini digunakan untuk mendapatkan ukuran dalam skala penuh, mengecil atau membesar. Apakah alatan ini?

a)

Pembaris Besi

b)

Pembaris Segitiga

c)

Pembaris Plastik

d)

Pita Pengukur

40.

Garis tebal berterusan dipanggil sebagai ...................

a)

Garisan Objek

b)

Garisan Tersembunyi

c)

Garisan PEngelasan

d)

Garisan Tengah

41.

The diagram shows the remaining solid when a cube is cut and removed from a cuboid.Which of the following is the orthogonal projection of the remaining solid to the vertical plane as viewed from X?

a)
b)
c)
d)
42.

The orthogonal projection of the object on a horizontal plane as viewed from Z is

a)
b)
c)
43.

The orthogonal projection of the object on a horizontal plane as viewed from Y is

a)
b)
c)
44.

The orthogonal projection of the object on a horizontal plane as viewed from X is

a)
b)
c)
45.

What type of drawing is this?

a)

Orthogonal

b)

Isometric

c)

Oblique

d)

I don't know

46.

Identify the type of pictoral

a)

Isometric

b)

Perspective

c)

Oblique

d)

Orthogonal

47.

What is an isometric projection?

a)

Isometric drawing is way of presenting designs/drawings in three dimensions.

b)

Isometric drawing is way of presenting designs/drawings in two dimensions.

c)

I don't know

48.

What is the angle set out for isometric projection?

a)

90-degree angles

b)

40-degree angles

c)

30-degree angles

d)

I don't know

49.

Apa tujuan perisai pemadam dalam lukisan kejuruteraan?

a)

Untuk melindungi kertas

b)

Untuk melukis garis lurus

c)

Untuk mengukur sudut

d)

Untuk memadam garis yang tidak diingini dengan tepat

50.

Apakah alat yang digunakan untuk membuat garis lengkung yang tidak dapat dilukis oleh jangka lukis dalam lukisan kejuruteraan?

a)

Pemisah

b)

T-kuasa

c)

Lengkung Perancis

d)

Penggaris sudut

51.

Apakah kelebihan utama menggunakan pensel mekanikal dalam lukisan kejuruteraan?

a)

Ia lebih mudah untuk dipegang

b)

Ia lebih tahan lama

c)

Ia mencipta garisan yang lebih tebal

d)

Ia tidak memerlukan pengasahan

52.

Mengapa kertas lukisan perlu ditutup apabila tidak digunakan dalam lukisan kejuruteraan?

a)

Untuk mengelakkan kesan comot

b)

Untuk mengekalkan kehangatan

c)

Untuk menyembunyikan kesilapan

d)

Untuk kelihatan kemas

53.

Apa kegunaan divider dalam lukisan kejuruteraan?

a)

Untuk membahagikan jarak dengan sama

b)

Untuk memadam garisan

c)

Untuk melukis bulatan

d)

Untuk mengukur sudut

54.

Bagaimanakah pensel mekanikal patut dibersihkan sebelum digunakan dalam lukisan kejuruteraan?

a)

Menggunakan pemadam

b)

Menggunakan kain

c)

Menggunakan berus

d)

Menggunakan air

55.

Apa yang harus digunakan untuk mengeluarkan habuk dan sisa pemadam dari kertas lukisan dalam lukisan kejuruteraan?

a)

Pemadam

b)

Kain

c)

Berus

d)

Tangan

56.

Mengapa penting untuk mengangkat T-square sebelum menggerakkannya dalam lukisan kejuruteraan?

a)

Untuk membersihkan T-square

b)

Untuk mengekalkan garis lurus

c)

Untuk mengelakkan T-square rosak

d)

Untuk mengelakkan kertas menjadi kotor

57.

Apa tujuan berus dalam lukisan kejuruteraan?

a)

Untuk membersihkan kertas

b)

Untuk memadam kesilapan

c)

Untuk melukis garis

d)

Untuk melukis warna

58.

Mengapa pensel mekanikal tidak sepatutnya digigit dalam lukisan kejuruteraan?

a)

Untuk membuatnya tahan lebih lama

b)

Untuk mengelakkan kesan dakwat

c)

Untuk mengelakkan patahnya dakwat

d)

Untuk menjaga kebersihannya

59.

Apa tujuan pemadam dalam lukisan kejuruteraan?

a)

Untuk mencipta bayangan

b)

Untuk memadam kesilapan

c)

Untuk melukis garisan yang lebih tebal

d)

Untuk mengukur jarak

60.

Bagaimana T-square sepatutnya dipindahkan untuk mengelakkan kertas daripada kotor dalam lukisan kejuruteraan?

a)

Tariknya dengan cepat

b)

Guna sebagai pembaris

c)

Angkat sebelum digerakkan

d)

Tekan dengan kukuh