Font size
WorksheetsDRawing Standards and Conventions
Total questions: 55
Worksheet time: 47mins
What is the use of Continuous thick line?
Used for visible outlines and edges.
Used for hidden outlines and edges.
Used for center lines.
Used for dimension lines.
What is the use of Continuous thin line?
Used for projection, dimensioning, leader lines, hatching and short centre lines.
Used for indicating hidden edges.
Used for cutting planes.
Used for center lines.
What is the use of Continuous thin straight with zigzags line?
Used for limits of partial or interrupted views and sections if the limit is not an axis.
Used for dimension lines.
Used for center lines.
Used for cutting planes.
What is the use of Dashed thin line?
Used for hidden outlines and edges.
Used for visible outlines and edges.
Used for dimension lines.
Used for center lines.
What is the use of Chain thin line?
Used for centre lines, lines of symmetry.
Used for dimension lines.
Used for hidden edges.
Used for cutting planes.
What is the use of Chain thin double dash line?
Used for ghost outlines and bend lines.
Used for dimension lines.
Used for center lines.
Used for section lines.
What is the use of Continuous thin irregular line?
Used as the limit to an interrupted view when an axis is not present.
Used to represent the center of circles and arcs.
Used to indicate hidden edges and surfaces.
Used to show the path of motion.
What is the use of Chain thin thick at both ends and changes in direction line?
Used on Cutting planes.
Used for dimension lines.
Used for center lines.
Used for hidden lines.
What is the length of the longest dimension in the diagram?
Identify the feature labeled as 'Small arrow' in the diagram.
Small arrow
Large arrow
Circle
Square
What is the purpose of the 'Short extension (Leader)' in the diagram?
To provide additional support
To connect different parts
To enhance visual appeal
To indicate direction
What is the largest dimension shown in the drawing?
3mm
50mm
100mm
25mm
The symbol for a square section is ____.
The symbol for a square section is a square shape.
The symbol for a square section is a circle shape.
The symbol for a square section is a triangle shape.
The symbol for a square section is a rectangle shape.
What is the main characteristic of parallel dimensioning?
It uses a common reference line for all dimensions.
It measures dimensions from different baselines.
It allows for flexible dimension placement.
It requires dimensions to be in a specific order.
Chain dimensioning should be used when:
there is a need for cumulative tolerance.
individual features need separate tolerances.
the design requires maximum material condition.
the features are unrelated.
Which dimensioning method is shown in the diagram with dimensions 25, 55, and 80?
What is the correct way to dimension radii according to the image?
Fill in the blank: The symbol ___ is placed in front of the dimension when dimensioning radii.
The symbol 'R' is placed in front of the dimension when dimensioning radii.
The symbol 'D' is placed in front of the dimension when dimensioning radii.
The symbol 'C' is placed in front of the dimension when dimensioning radii.
The symbol 'L' is placed in front of the dimension when dimensioning radii.
Explain the concept of dimensional tolerances as described in the image.
Dimensional tolerances refer to the permissible limit or limits of variation in a physical dimension.
Dimensional tolerances are the exact measurements required for a part.
Dimensional tolerances are not important in manufacturing.
Dimensional tolerances are only used in theoretical physics.
What is the tolerance of the button made for the TV remote as shown in the example?
0.5mm
1mm
0.25mm
0.75mm
In the example of the electrical plug pin, what is the basic height stated?
9.75mm
10mm
10.25mm
0.5mm
Fill in the blank: The tolerance applied to the height of the pin in the electrical plug example is ______.
0.25mm.
0.5mm.
1.0mm.
0.75mm.
What is the tolerance range for the length of the part of the clip?
The question has a diagram associated with it. The diagram has been stored separately.
±0.1 mm
±0.5 mm
±1.0 mm
Which of the following is an example of a functional dimension?
Height of the inside button
Length of the part of the clip
Remote button and electrical pin of the plug
Length of the pin
What is the difference between functional and non-functional dimensions?
Functional dimensions relate to specific tasks and processes, while non-functional dimensions relate to the overall system performance.
Functional dimensions are about the system's performance, while non-functional dimensions are about specific tasks.
Functional dimensions are related to hardware, while non-functional dimensions are related to software.
Functional dimensions are about user interface, while non-functional dimensions are about user experience.
Identify the type of tolerance shown in the diagram with a range of 20 ± 0.25.
Common
Symmetrical
Asymmetrical
What does the scale 1:1 represent in a drawing?
Fill in the blank: When we carry out a drawing and reduce all the sizes by a factor of 2, this is called scaling ______ the drawing.
down
up
sideways
backwards
What does the scale 2:1 indicate about the size of the drawing compared to the actual object?
What is the scale if the size of an object is increased by a factor of 10?
5
10
20
100
Which of the following is a recommended scale for reduction in engineering drawings?
2:1
1:5
10:1
50:1
Which of the following is a recommended scale for enlargement in engineering drawings?
A) 1:2
B) 1:10
C) 5:1
D) 1:100
The purpose of sectional views in drawings is to:
show the exterior of an object
illustrate the internal features of an object
provide a 3D view of an object
highlight the color scheme of an object
Which line is used to show the cutting plane in sectioned drawings?
Cutting Plane Line
Hidden Line
Center Line
Dimension Line
Fill in the blank: Where parts are cut by the cutting plane, they are hatched using a thin line drawn at ____.
45 degrees
30 degrees
60 degrees
90 degrees
Which of the following parts are not normally sectioned?
Shafts
Ribs
Webs
All of the above
What is the convention for drawing stepped section views?
Use a continuous line for the cutting plane
Use a broken line for the cutting plane
Use a zigzag line for the cutting plane
Use a dotted line for the cutting plane
Which of the following is a type of DTP software package?
MS Publisher
AutoCAD
SolidWorks
SketchUp
List the types of DTP software packages mentioned in the text.
Adobe InDesign, QuarkXPress, Microsoft Publisher
CorelDRAW, Adobe Photoshop, GIMP
AutoCAD, SketchUp, Revit
Microsoft Word, Google Docs, LibreOffice Writer
What is a Revolved Section?
A) A section that is turned through 90 degrees to show the reader what the section looks like.
B) A section that is removed from the drawing.
C) A section that shows only part of the component.
What does a Removed Section show?
A) The entire component.
B) The cut section out with the actual drawing.
C) Only part of the component sectioned.
A Part Section is used to show hidden detail such as a _______.
blind hole.
solid block.
visible hole.
transparent cover.
The purpose of a Woodruff Key in mechanical assemblies is to:
transmit torque between a shaft and a component
provide electrical insulation
act as a lubricant
reduce noise in machinery
Identify the type of thread shown in the diagram labeled 'Internal threads (Blind hole)'.
Explain the difference between a blind hole and a through hole in the context of internal threads.
A blind hole is partially drilled and does not go through the entire material, while a through hole goes completely through.
A blind hole is used for external threads, while a through hole is used for internal threads.
A blind hole is larger in diameter than a through hole.
A blind hole is used in softer materials, while a through hole is used in harder materials.
What is the simplified view of a spring as shown in the diagram?
Identify the conventional break lines for a solid shaft from the diagram.
The conventional break lines for a solid shaft are typically represented by zigzag lines or a series of short, straight lines that indicate where the shaft is broken or interrupted in the diagram.
The conventional break lines for a solid shaft are represented by dashed lines that run parallel to the shaft.
The conventional break lines for a solid shaft are shown as wavy lines that curve around the shaft.
The conventional break lines for a solid shaft are depicted by dotted lines that form a circular pattern around the shaft.
What is the dimension labeled as '1.5D' in the bolt diagram?
1.5 times the diameter
2 times the diameter
1.5 times the length
2.5 times the diameter
What is the pattern shown on the leftmost part of the diagram?
Straight knurl
Diamond Pattern knurl
Roller Bearing
Thread
Identify the component labeled as 'Roller Bearing' in the diagram.
Roller Bearing
Ball Bearing
Gear
Shaft
The purpose of the 'Chamfer' in mechanical components is to:
reduce stress concentration
increase material strength
improve thermal conductivity
enhance electrical insulation
Which type of screw is shown with a cross slot in the diagram?
A) Hexagon head screw
B) Countersunk screw, slot
C) Countersunk screw, cross slot
What is the simplified representation of a flat surface in the diagram?
Plane
Line
Point
Circle
What information must a Title Block always have when producing CAD drawings?
The purpose of the third angle projection symbol in CAD drawings is to:
indicate the scale of the drawing
show the method of projection used
represent the dimensions of the object
illustrate the material of the object
