PROTECH PRACTICE

1.       The following statements refer to replacing the steering rack boot. Select the statement that is False.

• a. To separate the tie rod end from the steering knuckle, tap the steering knuckle with a plastic hammer.

• b.      For installation of the tie rod end, align the matchmark applied when removing the lock nut and tie rod end, and tighten the lock nut to the specified torque after adjusting toe-in.

• c.       When installing the steering rack boots on the rack ends, confirm that the boots are not twisted or distorted using the joint lines on the boots.

• d.      Make sure to use a new cotter pin to fasten the castle nut after tie rod end installation.

The following statements refer to the inspection for fuel leaks performed after the fuel sedimeter filter on a diesel engine is replaced. Select the statement that is True.

• a.      Turn the ignition switch to the ON position and make sure that fuel does not leak from the filter installation surface and switch installation surface.

• b. Push the priming pump until it becomes hard and make sure that fuel does not leak from the filter installation surface and switch installation surface.

• c. Start the engine once and stop it. After leaving it for a period of time, make sure that fuel does not leak from the filter installation surface and switch installation surface.

• d.      After warming up the engine, stop it and then make sure that fuel does not leak from the filter installation surface and switch installation surface.

The following statements refer to replacing ATF. Select the statement that is False.

• a.      Use of ATF other than the specified type may result in shift shock transitions as well as worsening fuel economy.

• b.            ATF in the torque in the torque converter can be drained from the drain plug of the oil pan.

• c.       ATF is classified as a periodically replaced part, so it is necessary to replace it on a regular basis.

• d.      Low fluid levels may lead to insufficient lubrication of the automatic transaxle mechanism, causing seizure.

Which of the following statements about the drive shaft is True?

• a.      The drive shaft boots clamp can be reused as long as there is no serious damage.

• b.      In the drive shaft replacement procedure, the grease that comes with the boots kit is not measured, so measure the amount of grease before adding.

• c. Generally, the outboard joint on the drive shaft is a non-disassembly part..

• d.            For the drive shaft boots, generally the inboard side is more easily damaged than the outboard side.

Which of the following statements about drive shaft boots replacement is True?

• a.      When separating the tie rod end from the steering knuckle, separate it by hitting the tie rod end with a hammer.

• b. When removing the drive shaft from the transaxle, one person supports the drive shaft and the other removes the drive shaft using SST.

• c.             When removing the tripod joint roller, remove the tripod joint roller by hitting the roller.

• d.      When applying grease to the outboard joint, apply new grease on the old grease.

Which of the following statements about the battery charge is True?

• When the battery fluid level is low, add tap water.
• When performing battery charge, disconnect only the battery negative terminal.
• During battery charge, pay attention so that the battery fluid temperature does not exceed 80 degrees Celsius.
• Stop battery charging immediately in these cases: Voltage or specific gravity doesn't increase; gas doesn't generate properly; the temperature increases significantly.

Which of the following statements about brake shoe replacement is True?

A: Foot brake sharing type parking brake should be adjusted after the brake shoe is replaced.

B: If the brake lining has gone because of wear, the brake drum could be damaged.

• Only A is true
• Only B is true
• Both A and B are true
• Both A and B are false

Which of the following statements about air bleeding in the brake line is True?

• When bleeding the air, always observe the brake fluid level in the master cylinder, and fill with fluid when the reservoir tank becomes empty.
• When bleeding the air, perform the procedure of filling the fluid. This is because air will enter the master cylinder when the reservoir tank becomes empty.
• When bleeding the air, close the bleeder plug while the assistant is not depressing the brake pedal. When depressing the brake pedal, air may enter the brake line.
• For the air bleeding procedure, after bleeding all the fluid in the brake line, perform with the brake fluid filling into the master cylinder reservoir tank.

Which of the following statements about wiper rubber installation and inspection is True?

• The length of the wiper rubber can be adjusted by cutting the rubber on the side with no fixing hole.
• When installing a wiper rubber with backing plate, install the backing plate on the wiper rubber first and then install the wiper blade.
• When installing a wiper rubber with no backing plate, pass the side of the rubber with no small protrusion through the notch on the wiper blade
• When completing wiper rubber replacement, place sand, etc., on the glass and check the wiping performance.

Which of the following statements about bulb replacement is False?

• Attaching oil at the bulb terminal causes terminal corrosion, so hold the bulb on the glass side.
• When replacing the bulb with a new one, use the same wattage of bulb as the removed one.
• After bulb replacement, be sure to check the operation.
• After the bulb is removed, leaving the lamp assembly for a long time could allow foreign objects or moisture to get in, so immediate replacement is required.