What is the function of the HV-rated cut-off switch in a vehicle's tractive system?

To provide power to the safety appliances and auxiliaries

What happens to the reverse light and reverse alarm when the Kill switch is activated?

They may or may not work, depending on the design of the vehicle

What happens to the Brake Light when the Kill switch is pressed?

It works only when the Kill switch is deactivated

It works only when the vehicle is moving

Which of the following is a requirement for the angle between the LDB members and the RRH vertical members?

The angle must be greater than or equal to 20 degrees.

The angle must be less than 20 degrees.

The angle must be exactly 20 degrees.

There is no specific requirement for the angle.

Which of the following describes the height requirements for the SIM members in relation to the inside seat bottom, as shown in Figure ?

The SIM members must be between 203 mm (8 in.) and 356 mm (14 in.) at all positions between points S and D.

The SIM members must be below 203 mm (8 in.) at all positions between points S and D.

The SIM members must be above 356 mm (14 in.) at all positions between points S and D.

The height requirements for the SIM members do not vary between points S and D.

Which of the following describes the required total weld length of a gusset, in relation to the circumference of the primary material used?

The total weld length should be twice the tubing circumference.

The total weld length should be equal to the tubing circumference.

The total weld length should be half the tubing circumference.

The total weld length should be four times the tubing circumference.

Which of the following describes the minimum thickness required for the material used for plate gussets, as compared to the thickness of the primary material used?

The thickness of the plate gusset must be greater than or equal to the thickness of the primary material.

The thickness of the plate gusset must be less than the thickness of the primary material.

The thickness of the plate gusset must be equal to the thickness of the primary material.

There is no specific thickness requirement for the plate gusset material.

Which of the following describes the criteria for determining whether tubes need to be sleeved when joined at an angle?

Tubes need not be sleeved when joined at an angle greater than 5 degrees.

Tubes must be sleeved when joined at any angle, regardless of the degree.

Tubes need not be sleeved when joined at an angle less than 5 degrees.

Tubes need to be sleeved when joined at an angle less than or equal to 5 degrees.

Which of the following describes the minimum length requirement for a linear weld used to secure a sleeve inside a joint, including the butt joint and the rosette welds?

C) The minimum length requirement for the linear weld is 102 mm (4.0 in.).

A) The minimum length requirement for the linear weld is 50 mm (2.0 in.).

B) The minimum length requirement for the linear weld is 76 mm (3.0 in.).

D) There is no specific minimum length requirement for the linear weld.

What is the mandatory type for both the Kill Switches in a vehicle's tractive system?

"PUSH TO KILL" type & "ROTATE TO ENERGIZE" type

"PUSH TO KILL" type & "ROTATE TO DE-ENERGIZE" type

Which of the following describes the requirements for the primary roll cage members and bracing?

The primary roll cage members and bracing must be made from circular steel tubing with an outside diameter of 25 mm (1.0 in), a wall thickness of 3 mm (0.120 in.), and a carbon content of at least 0.18%.

The primary roll cage members and bracing can be made from any material.

The primary roll cage members and bracing must be made from circular steel tubing with an outside diameter of 25 mm (1.0 in) and a wall thickness of 3 mm (0.120 in.).

The primary roll cage members and bracing must be made from steel with a carbon content of at least 0.18%.

What is the requirement for reinforcing frame members that need to be drilled for mounting fasteners or routing accessories?

Frame members should be reinforced with a weld-in sleeve.

Reinforcement is not necessary.

Frame members should be reinforced with a bolt-on sleeve.

Frame members should be replaced with thicker material.

What is the function of an anti-submarine belt?

To positively locate the buckle and prevent the driver from riding under the lap belts.

To prevent the driver from steering out of control.

To provide additional support to the driver's back.

To prevent the driver from sliding forward in the seat during a collision.

What are the requirements for driver restraint systems?

The material of shoulder and lap belts shall be of Nylon or Dacron polyester and in new or like-new condition, 76 mm in width, and free from injurious defects. Anti-submarine belts shall meet the same conditions but have a minimum width of 51 mm.

The material of shoulder and lap belts shall be of Nylon or Dacron polyester and in new or like-new condition, 51 mm in width, and free from injurious defects.

The material of shoulder and lap belts shall be of Nylon or Dacron polyester and in new or like-new condition, 76 mm in width, and free from injurious defects. Anti-submarine belts are not requ

The material of shoulder and lap belts shall be of Nylon or Dacron polyester and in new or like-new condition, 76 mm in width, and free from injurious defects. Anti-submarine belts shall meet the same conditions but have a minimum width of 76 mm.

What is the requirement regarding the placement of Accumulator(s) containers?

It must be placed behind the firewall.

It must be placed in the cockpit area.

It must be placed ahead of the firewall.

It can be placed anywhere in the vehicle.

What is the maximum and minimum position for the shoulder belt mounting point (A) with respect to the driver's shoulders?

No higher than the driver's shoulders and no lower than 102 mm (4.0 in.) below the shoulders

No higher than 102 mm (4.0 in.) above the driver's shoulders and no lower than the driver's shoulders

No higher than 76 mm (3.0 in.) above the driver's shoulders and no lower than 127 mm (5.0 in.) below the shoulders

No higher than 203 mm (8.0 in.) above the driver's shoulders and no lower than 152 mm (6.0 in.) below the shoulders

Which of the following is true regarding the securing of anti-submarine belts?

Anti-submarine belts should not be secured with eyebolts.

Anti-submarine belts should be secured with eyebolts.

Anti-submarine belts can be secured with any type of bolt.

Anti-submarine belts can only be secured with carabiners

Which of the following statements is true about the seat back angle for an upright seating position?

It is between 65 deg and 90 deg.

In what scenarios is it required to protect tractive system parts by a fully triangulated structure?

When the tractive system parts have clearance from the ground < 350mm

When the tractive system parts have clearance from the ground < 150mm

When the tractive system parts have clearance from the ground < 250mm

When the tractive system parts have clearance from the ground < 450mm

Which of the following is a requirement for the TSAL (Traffic Signal Aircraft Warning Light)?

It must be a round beacon type with an amber flashing light (>350 Lumens per unit, IP65 rated) with a frequency of 2Hz-5Hz.

It must be a rectangular beacon type with a blue flashing light.

It must be a round beacon type with a red flashing light.

It can be any shape and color as long as it is visible in all directions.

What is the recommended placement for the TSAL (Traffic Signal Aircraft Warning Light)?

It should be fitted behind the BLC in the middle to ensure visibility from all directions.

It should be placed on top of the BLC (Building Line Control).

It should be placed on the side of the BLC to avoid interference.

It should be placed at the bottom of the BLC for better visibility.

The BAJA vehicle must be capable of carrying one (1) person

75 inches tall weighing 250 lbs

67 inches tall weighing 250 lbs

Secondary members must be steel tubes having a minimum wall thickness of -------- and a minimum outside diameter of -----

0.89 mm (0.035 in) & 25.4 mm (1.0 in)

0.89 mm (0.037 in) & 25.4 mm (1.0 in)

0.88 mm (0.035 in) & 25.8 mm (1.0 in)

eBAJA 2024 Team Selection Exam

Authored by vinod mummina

Other

Professional Development

Used 2+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

80 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the definition of "High Voltage" in automotive engineering?

Voltage in the range of 30 to 1000 VDC RMS

Voltage in the range of 60 to 1500 VDC

Voltage in the range of 30 to 1000 VAC RMS or 60 to 1500 VDC

Voltage in the range of 30 to 1500 VAC RMS

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the maximum voltage allowed between any two terminals of the Low Voltage system in a vehicle?

10V DC

15V DC

10V AC

15V AC

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the maximum voltage allowed between any two terminals of the tractive system in a vehicle?

30V DC

30V AC

60V DC

60V AC

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the function of the tractive system in a vehicle?

To control the speed of the vehicle

To provide power to the accessories in the vehicle

To provide power to the motor that propels the vehicle

To regulate the temperature of the vehicle's battery

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What type of DC-DC converter should teams use in their vehicle?

Optoisolated marine grade

Optoisolated automotive grade

Non-isolated automotive grade

Non-isolated industrial grade

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Where should the HV-rated cut-off switch be located in the vehicle's tractive system?

Between the DC-DC Converter and the motor controller

Between the tractive system Accumulator(s) and the DC-DC Converter

Between the tractive system Accumulator(s) and the motor controller

Between the charging system and the tractive system Accumulator(s)

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What happens to the safety appliances and auxiliaries when the HV-rated cut-off switch and GLV ignition/master switch are on?

They are also turned off

They continue to work irrespective of the kill switch position

They only work when the kill switch is activated

They work only when the vehicle is moving

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

85 questions

Old Question Paper 2023 as on July 2024

Quiz

•

Professional Development

80 questions

MECHANIC

Quiz

•

Professional Development

78 questions

Kosakata Modul Bab 4

Quiz

•

Professional Development

84 questions

চুক্তি আইন কুইজ

Quiz

•

Professional Development

75 questions

High Availability / Gate Load Balancing SAA Quiz

Quiz

•

Professional Development

77 questions

CPQ Exam_v3

Quiz

•

Professional Development

80 questions

PembaTIK 2023 Level 2

Quiz

•

Professional Development

79 questions

final exam

Quiz

•

Professional Development

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

10 questions

Probability Practice

Quiz

•

4th Grade

15 questions

Probability on Number LIne

Quiz

•

4th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

6 questions

Appropriate Chromebook Usage

Lesson

•

7th Grade

10 questions

Greek Bases tele and phon

Quiz

•

6th - 8th Grade

Discover more resources for Other

20 questions

Black History Month Trivia Game #1

Quiz

•

Professional Development

20 questions

90s Cartoons

Quiz

•

Professional Development

12 questions

Mardi Gras Trivia

Quiz

•

Professional Development

7 questions

Copy of G5_U5_L14_22-23

Lesson

•

KG - Professional Dev...

12 questions

Unit 5: Puerto Rico W1

Quiz

•

Professional Development

42 questions

LOTE_SPN2 5WEEK2 Day 4 We They Actividad 3

Quiz

•

Professional Development

15 questions

Balance Equations Hangers

Quiz

•

Professional Development

31 questions

Servsafe Food Manager Practice Test 2021- Part 1

Quiz

•

9th Grade - Professio...