After attaching four PCs to the switch ports, configuring the SSID and setting authentication properties for a small office network, a technician successfully tests the connectivity of all PCs that are connected to the switch and WLAN. A firewall is then configured on the device prior to connecting it to the Internet. What type of network device includes all of the described features?

standalone wireless access point

Which three steps should be taken before moving a Cisco switch to a new VTP management domain? (Choose three.)

Configure the switch with the name of the new management domain.

Select the correct VTP mode and version.

Configure the VTP server in the domain to recognize the BID of the new switch.

Download the VTP database from the VTP server in the new domain.

A network administrator is preparing the implementation of Rapid PVST+ on a production network. How are the Rapid PVST+ link types determined on the switch interfaces?

Link types are determined automatically.

Link types can only be configured on access ports configured with a single VLAN.

Link types can only be determined if PortFast has been configured.

Link types must be configured with specific port configuration commands.

How will a router handle static routing differently if Cisco Express Forwarding is disabled?

Ethernet multiaccess interfaces will require fully specified static routes to avoid routing inconsistencies.

It will not perform recursive lookups.

Static routes that use an exit interface will be unnecessary.

Serial point-to-point interfaces will require fully specified static routes to avoid routing inconsistencies.

Compared with dynamic routes, what are two advantages of using static routes on a router? (Choose two.)

They use fewer router resources.

They take less time to converge when the network topology changes.

They improve the efficiency of discovering neighboring networks.

What is the effect of entering the spanning-tree portfast configuration command on a switch?

It enables portfast on a specific switch interface.

It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.

Which two statements are characteristics of routed ports on a multilayer switch? (Choose two.)

In a switched network, they are mostly configured between switches at the core and distribution layers.

They are not associated with a particular VLAN.

The interface vlan command has to be entered to create a VLAN on routed ports.

They support subinterfaces, like interfaces on the Cisco IOS routers.

They are used for point-to-multipoint links.

Successful inter-VLAN routing has been operating on a network with multiple VLANs across multiple switches for some time. When an inter-switch trunk link fails and Spanning Tree Protocol brings up a backup trunk link, it is reported that hosts on two VLANs can access some, but not all the network resources that could be accessed previously. Hosts on all other VLANS do not have this problem. What is the most likely cause of this problem?

The protected edge port function on the backup trunk interfaces has been disabled.

The allowed VLANs on the backup link were not configured correctly.

Dynamic Trunking Protocol on the link has failed.

Inter-VLAN routing also failed when the trunk link failed.

Which command will start the process to bundle two physical interfaces to create an EtherChannel group via LACP?

interface range GigabitEthernet 0/4 – 5

What action takes place when a frame entering a switch has a multicast destination MAC address?

The switch will forward the frame out all ports except the incoming port.

The switch forwards the frame out of the specified port.

The switch adds a MAC address table entry mapping for the destination MAC address and the ingress port.

The switch replaces the old entry and uses the more current port.

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Check the configuration of the exit interface on the new static route.

Verify that there is not a default route in any of the edge router routing tables.

Check the configuration on the floating static route and adjust the AD.

Create a floating static route to that network.

A static route has been configured on a router. However, the destination network no longer exists. What should an administrator do to remove the static route from the routing table?

Remove the route using the no ip route command.

Change the administrative distance for that route.

Change the routing metric for that route.

Nothing. The static route will go away on its own.

What two default wireless router settings can affect network security? (Choose two.)

A well-known administrator password is set.

MAC address filtering is enabled.

The wireless channel is automatically selected.

A network administrator is configuring a WLAN. Why would the administrator change the default DHCP IPv4 addresses on an AP?

to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range

to restrict access to the WLAN by authorized, authenticated users only

to monitor the operation of the wireless network

to reduce the risk of interference by external devices such as microwave ovens

Which two functions are performed by a WLC when using split media access control (MAC)? (Choose two.)

frame translation to other protocols

association and re-association of roaming clients

packet acknowledgments and retransmissions

frame queuing and packet prioritization

On what switch ports should BPDU guard be enabled to enhance STP stability?

only ports that are elected as designated ports

only ports that attach to a neighboring switch

all trunk ports that are not root ports

Refer to the exhibit. What will router R1 do with a packet that has a destination IPv6 address of 2001:db8:cafe:5::1?

forward the packet out Serial0/0/0

forward the packet out GigabitEthernet0/0

forward the packet out GigabitEthernet0/1

Refer to the exhibit. Currently router R1 uses an EIGRP route learned from Branch2 to reach the 10.10.0.0/16 network. Which floating static route would create a backup route to the 10.10.0.0/16 network in the event that the link between R1 and Branch2 goes down?

ip route 10.10.0.0 255.255.0.0 209.165.200.225 100

ip route 10.10.0.0 255.255.0.0 Serial 0/0/0 100

ip route 10.10.0.0 255.255.0.0 209.165.200.226 100

ip route 10.10.0.0 255.255.0.0 209.165.200.225 50

Refer to the exhibit. R1 was configured with the static route command ip route 209.165.200.224 255.255.255.224 S0/0/0 and consequently users on network 172.16.0.0/16 are unable to reach resources on the Internet. How should this static route be changed to allow user traffic from the LAN to reach the Internet?

Change the destination network and mask to 0.0.0.0 0.0.0.0

Add an administrative distance of 254.

Change the exit interface to S0/0/1.

Add the next-hop neighbor address of 209.165.200.226.

Refer to the exhibit. Which static route command can be entered on R1 to forward traffic to the LAN connected to R2?

ipv6 route 2001:db8:12:10::/64 S0/0/1 fe80::2

ipv6 route 2001:db8:12:10::/64 S0/0/0

ipv6 route 2001:db8:12:10::/64 S0/0/0 fe80::2

ipv6 route 2001:db8:12:10::/64 S0/0/1 2001:db8:12:10::1

Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0?

The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation.

The default gateway address is not provided in the pool.

No clients have communicated with the DHCPv6 server yet.

The IPv6 DHCP pool configuration has no IPv6 address range specified.

Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?

the virtual IP address and the virtual MAC address for the HSRP group 1

the virtual IP address of the HSRP group 1 and the MAC address of R1

the virtual IP address of the HSRP group 1 and the MAC address of R2

the IP address and the MAC address of R1

Refer to the exhibit. How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?

SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.

SW1 forwards the frame directly to SW2. SW2 floods the frame to all ports connected to SW2, excluding the port through which the frame entered the switch.

SW1 floods the frame on all ports on the switch, excluding the interconnected port to switch SW2 and the port through which the frame entered the switch.

SW1 drops the frame because it does not know the destination MAC address.

Refer to the exhibit. A network administrator has connected two switches together using EtherChannel technology. If STP is running, what will be the end result?

STP will block one of the redundant links.

The switches will load balance and utilize both EtherChannels to forward packets.

The resulting loop will create a broadcast storm.

Both port channels will shutdown.

Refer to the exhibit. Host A has sent a packet to host B. What will be the source MAC and IP addresses on the packet when it arrives at host B?

Source MAC: 00E0.FE91.7799 Source IP: 10.1.1.10

Source MAC: 00E0.FE10.17A3 Source IP: 10.1.1.10

Source MAC: 00E0.FE10.17A3 Source IP: 192.168.1.1

Source MAC: 00E0.FE91.7799 Source IP: 10.1.1.1

Source MAC: 00E0.FE91.7799 Source IP: 192.168.1.1

Refer to the exhibit. Based on the exhibited configuration and output, why is VLAN 99 missing?

because VLAN 99 has not yet been created

because VLAN 99 is not a valid management VLAN

because there is a cabling problem on VLAN 99

because VLAN 1 is up and there can only be one management VLAN on the switch

Refer to the exhibit. Which route was configured as a static route to a specific network using the next-hop address?

S 10.17.2.0/24 [1/0] via 10.16.2.2

S 0.0.0.0/0 [1/0] via 10.16.2.2

S 10.17.2.0/24 is directly connected, Serial 0/0/0

C 10.16.2.0/24 is directly connected, Serial0/0/0

Refer to the exhibit. What can be concluded about the configuration shown on R1?

R1 is configured as a DHCPv4 relay agent.

R1 is operating as a DHCPv4 server.

R1 will broadcast DHCPv4 requests on behalf of local DHCPv4 clients.

R1 will send a message to a local DHCPv4 client to contact a DHCPv4 server at 10.10.10.8.

Refer to the exhibit. R1 has been configured as shown. However, PC1 is not able to receive an IPv4 address. What is the problem?

The ip helper-address command was applied on the wrong interface.

R1 is not configured as a DHCPv4 server.

A DHCP server must be installed on the same LAN as the host that is receiving the IP address.

The ip address dhcp command was not issued on the interface Gi0/1.

CISCO 2 FINAL EXAM Part 1/3

Authored by sahil jamsa

Computers

University

Used 20+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

44 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which option shows a correctly configured IPv4 default static route?

ip route 0.0.0.0 255.255.255.0 S0/0/0

ip route 0.0.0.0 0.0.0.0 S0/0/0

ip route 0.0.0.0 255.255.255.255 S0/0/0

ip route 0.0.0.0 255.0.0.0 S0/0/0

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

6. What is a method to launch a VLAN hopping attack?

introducing a rogue switch and enabling trunking

sending spoofed native VLAN information

sending spoofed IP addresses from the attacking host

flooding the switch with MAC addresses

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which statement is correct about how a Layer 2 switch determines how to forward frames?

Frame forwarding decisions are based on MAC address and port mappings in the CAM table.

Only frames with a broadcast destination address are forwarded out all active switch ports.

Unicast frames are always forwarded regardless of the destination MAC address.

Cut-through frame forwarding ensures that invalid frames are always dropped.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which statement describes a result after multiple Cisco LAN switches are interconnected?

The broadcast domain expands to all switches.

One collision domain exists per switch.

There is one broadcast domain and one collision domain per switch.

Frame collisions increase on the segments connecting the switches.

Unicast frames are always forwarded regardless of the destination MAC address.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

An administrator is trying to remove configurations from a switch. After using the command erase startup-config and reloading the switch, the administrator finds that VLANs 10 and 100 still exist on the switch. Why were these VLANs not removed?

Because these VLANs are stored in a file that is called vlan.dat that is located in flash memory, this file must be manually deleted.

These VLANs cannot be deleted unless the switch is in VTP client mode.

These VLANs are default VLANs that cannot be removed.

These VLANs can only be removed from the switch by using the no vlan 10 and no vlan 100 commands.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is a secure configuration option for remote access to a network device?

Configure an ACL and apply it to the VTY lines.

Configure 802.1x.

Configure SSH.

Configure Telnet.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which wireless encryption method is the most secure?

WPA2 with AES

WPA2 with TKIP

WEP

WPA

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

40 questions

MS office 2016

Quiz

•

1st Grade - Professio...

40 questions

Computer Network

Quiz

•

12th Grade - University

45 questions

Pagtatapos Isa

Quiz

•

University

40 questions

ENG-103 Vocab

Quiz

•

University

47 questions

MS Word Preliminary Examination

Quiz

•

10th Grade - University

40 questions

ICT-Department-Grade4-November

Quiz

•

4th Grade - University

40 questions

Cisco Packet Tracer

Quiz

•

University

40 questions

Discrete Structure (COS 203) CA

Quiz

•

University

Popular Resources on Wayground

8 questions

Spartan Way - Classroom Responsible

Quiz

•

9th - 12th Grade

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

14 questions

Boundaries & Healthy Relationships

Lesson

•

6th - 8th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

3 questions

Integrity and Your Health

Lesson

•

6th - 8th Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

9 questions

FOREST Perception

Lesson

•

20 questions

Main Idea and Details

Quiz

•

5th Grade

Discover more resources for Computers

20 questions

Disney Trivia

Quiz

•

University

7 questions

Fragments, Run-ons, and Complete Sentences

Interactive video

•

4th Grade - University

7 questions

Renewable and Nonrenewable Resources

Interactive video

•

4th Grade - University

10 questions

DNA Structure and Replication: Crash Course Biology

Interactive video

•

11th Grade - University

7 questions

Force and Motion

Interactive video

•

4th Grade - University

20 questions

Implicit vs. Explicit

Quiz

•

6th Grade - University

14 questions

Ch.3_TEACHER-led

Quiz

•

University

7 questions

Comparing Fractions

Interactive video

•

1st Grade - University

CISCO 2 FINAL EXAM Part 1/3

Which option shows a correctly configured IPv4 default static route?

6. What is a method to launch a VLAN hopping attack?

Which statement is correct about how a Layer 2 switch determines how to forward frames?

Which statement describes a result after multiple Cisco LAN switches are interconnected?

An administrator is trying to remove configurations from a switch. After using the command erase startup-config and reloading the switch, the administrator finds that VLANs 10 and 100 still exist on the switch. Why were these VLANs not removed?

What is a secure configuration option for remote access to a network device?

Which wireless encryption method is the most secure?

What protocol or technology disables redundant paths to eliminate Layer 2 loops?

Which two VTP modes allow for the creation, modification, and deletion of VLANs on the local switch? (Choose two.)

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers