What is the purpose of fitting a valve to every supply pipe supplying water to premises?

To enable the supply to be shut off to those premises without shutting off the supply to any other premises

Where must a stop valve be sited at the boundary of the property?

Immediately as the supply enters the premises

At the highest point of the property

At the lowest point of the property

How close should the internal stop valve be to the point of entry?

As close as possible to the point of entry

As far as possible from the point of entry

Where should servicing valves be installed according to the provided learning material?

On inlets to all float-operated valves, washing machines and dishwashers, cisterns, water heaters, water softeners, hot water distribution pipes, and cold-feed pipes

Only on washing machines and dishwashers

Only on hot water distribution pipes

What is the primary purpose of fitting servicing valves as close as reasonably practicable to float-operated valves or other inlet devices of an appliance?

To ensure they are readily accessible

On larger installations, servicing valves or stop valves should be fitted to:

Isolate pipework on different floors

Isolate various parts of an installation

Isolate branch pipe to a range of appliances

Drinking-water supply shall be supplied with water from:

A pump delivery pipe drawing water from a supply pipe

A distributing pipe drawing water exclusively from a storage cistern supplying wholesome water

What is the primary function of a cistern in a cold water storage system?

To store water at atmospheric pressure

In a high-rise building, why might it be necessary to install a pump or booster system?

To ensure water supply to higher flats

To increase the water pressure for lower flats

To reduce the water pressure in the supply pipe

To prevent water leakage in the building

What is the purpose of the large capacity of water in the pneumatic pressure vessel?

To stop the pump operating for short time periods

To increase the water temperature

What is the purpose of a break cistern in a water supply system?

To separate the incoming supply from the boosted supply

To store water for emergency use

To filter impurities from the water

To heat the water before distribution

What component is used to control the pump in a break cistern system?

A pressure sensor with a membrane

Where is drinking water taken from in a break cistern system when the mains pressure is sufficient?

Directly from the break cistern

What is the function of the duplicate pumps in a break cistern system?

To provide redundancy in case one pump fails

What triggers the pumps to start in the break cistern system?

When the water level falls to a predetermined level

When the water level rises to a predetermined level

When the water temperature reaches a certain point

What is recommended to keep the interior of a cistern when drinking water is supplied directly from it?

It should be filled to the top.

Why should the quantity of stored water in a cistern be restricted to the minimum essential amount required?

To maximize the throughput of water.

To prevent the cistern from overflowing.

To keep the water temperature high.

What should be done to a cistern to ensure it is properly insulated and ventilated?

It should be fitted with a screened warning/overflow pipe.

It should be filled to the top.

What is the purpose of an overflow pipe in a cistern?

To discharge any overflowing water to a position where it will not cause damage to the building.

To give warning to the owners or occupiers of a building that a cistern is overflowing.

To prevent water from entering the cistern.

To filter the water entering the cistern.

What is the recommended action for cisterns with a capacity greater than 1000 litres?

Provide both a warning pipe and an overflow pipe.

Provide only a single warning/overflow pipe.

No additional pipes are required.

Where should all warning pipes discharge?

In the same position as the overflow pipe

What is the function of a warning pipe in a cistern?

To give warning to the owners or occupiers of a building that a cistern is overflowing

To discharge any overflowing water to a safe position

To filter the water entering the cistern

To prevent water from entering the cistern

What is the primary function of an overflow/warning pipe in a cistern?

To remove excess water from the cistern

To heat the water in the cistern

To filter the water in the cistern

Where should warning pipes discharge?

In a conspicuous position, preferably in an external location

What must feed and expansion cisterns have in relation to warning pipes?

Separate warning pipes from those servicing cold water cisterns

Shared warning pipes with cold water cisterns

Warning pipes only for hot water

How should the warning or overflow pipe be arranged when there are two or more cisterns?

So that the cisterns are isolated from each other

So that one cistern can discharge into the other

So that the water flows in a loop

So that the water is stored in both cisterns equally

What should be included in the installation of a cistern with a capacity greater than 5000 litres?

A level indicator and an audible or visible alarm

At what water level should the audible or visible alarm operate in a cistern with a capacity greater than 5000 litres?

25mm below the opening of the overflow

10mm below the opening of the overflow

50mm below the opening of the overflow

75mm below the opening of the overflow

What is an alternative method to a warning pipe for cisterns larger than 5000 litres?

A float-operated water level indicator

Cold Water Systems in Buildings

Authored by Zoheir Kichou

Architecture

Professional Development

Used 1+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

66 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is one of the principles of operation of cold water system component layouts used in multi-storey buildings?

They use gravity to distribute water.

They rely on solar power for heating.

They are designed to minimize water pressure.

They use wind energy for water distribution.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is a requirement for large scale storage cisterns?

They must be made of metal.

They should be able to store a large volume of water.

They need to be underground.

They must be transparent.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the function of components used in boosted cold water systems in multi-storey buildings?

To heat the water.

To increase water pressure.

To filter the water.

To reduce water usage.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is one method of treating water for use in buildings?

Boiling the water.

Using chemical disinfectants.

Filtering through sand.

Exposing to sunlight.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the method of operation of different types of boosted cold water supply systems for buildings?

They use solar panels.

They rely on electric pumps.

They use wind turbines.

They depend on manual pumping.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

In what situations might rainwater harvesting be appropriate?

In areas with frequent rainfall.

In desert regions.

In places with abundant groundwater.

In urban areas with no rainfall.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the purpose of stop valves in a multi-storey system layout?

To regulate the flow of water to individual properties

To increase the water pressure in the building

To provide heating to the building

To control the electrical supply to the building

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

65 questions

History of Architecture

Quiz

•

Professional Development

Popular Resources on Wayground

8 questions

Spartan Way - Classroom Responsible

Quiz

•

9th - 12th Grade

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

14 questions

Boundaries & Healthy Relationships

Lesson

•

6th - 8th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

3 questions

Integrity and Your Health

Lesson

•

6th - 8th Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

9 questions

FOREST Perception

Lesson

•

20 questions

Main Idea and Details

Quiz

•

5th Grade

Discover more resources for Architecture

15 questions

LOTE_SPN2 5WEEK3 Day 2 Itinerary

Quiz

•

Professional Development

6 questions

Copy of G5_U6_L5_22-23

Lesson

•

KG - Professional Dev...

10 questions

March Quiz

Quiz

•

Professional Development

5 questions

Copy of G5_U6_L8_22-23

Lesson

•

KG - Professional Dev...

10 questions

suffixes FUL OR LESS

Quiz

•

Professional Development

Cold Water Systems in Buildings

What is one of the principles of operation of cold water system component layouts used in multi-storey buildings?

What is a requirement for large scale storage cisterns?

What is the function of components used in boosted cold water systems in multi-storey buildings?

What is one method of treating water for use in buildings?

What is the method of operation of different types of boosted cold water supply systems for buildings?

In what situations might rainwater harvesting be appropriate?

What is the purpose of stop valves in a multi-storey system layout?

In the recommended locations of stop valves for a block of flats fed from a common supply pipe, where is the main internal stop valve located?

Where must the internal stop valve be located in a premises?

What is the purpose of fitting a valve to every supply pipe supplying water to premises?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Architecture