CISCOExam

Consider the following output for an ACL that has been applied to a router via the access-class in command. What can a network administrator determine from the output that is shown?

• • Two devices connected to the router have IP addresses of 192.168.10. x .

• • Two devices were able to use SSH or Telnet to gain access to the router.

  
  

• • Traffic from one device was not allowed to come into one router port and be routed outbound a different router port.

  
  

• • Traffic from two devices was allowed to enter one router port and be routed outbound to a different router port.

  
  

Refer to the exhibit. A technician is configuring R2 for static NAT to allow the client to access the web server. What is a possible reason that the client PC cannot access the web server?

• • The IP NAT statement is incorrect.

• • Interface Fa0/1 should be identified as the outside NAT interface.

  
  

• Interface S0/0/0 should be identified as the outside NAT interface.
  

• • The configuration is missing a valid access control list.

  
  

Refer to the exhibit. Which address or addresses represent the inside global address?

• • 192.168.0.100

  
  

• • 10.1.1.2

  
  

• • any address in the 10.1.1.0 network

  
  

• • 209.165.20.25

  
  

Refer to the exhibit. Routers R1 and R2 are connected via a serial link. One router is configured as the NTP master, and the other is an NTP client. Which two pieces of information can be obtained from the partial output of the show ntp associations detail command on R2? (Choose two.)

• • Both routers are configured to use NTPv2.

  
  

• Router R1 is the master, and R2 is the client

  
  

• • The IP address of R2 is 192 168.1.2.

  
  

• • Router R2 is the master, and R1 is the client

  
  

• • The IP address of R1 is 192.168.1.2

  
  

Refer to the exhibit. If the network administrator created a standard ACL that allows only devices that connect to the R2 G0/0 network access to the devices on the R1 G0/1 interface, how should the ACL be applied?

• • inbound on the R2 G0/0 interface

  
  

• • outbound on the R1 G0/1 interface

  
  

• • inbound on the R1 G0/1 interface

  
  

• • outbound on the R2 S0/0/1 interface

  
  

Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

• • The DR can be reached through the GigabitEthernet 0/0 interface.

  
  

• • There have been 9 seconds since the last hello packet sent.

  
  

• • This interface is using the default priority.

  
  

• The router ID values were not the criteria used to select the DR and the BDR.
  

• • The router ID on the DR router is 3.3.3.3

Refer to the exhibit. A network administrator is configuring an ACL to limit the connection to R1 vty lines to only the IT group workstations in the network 192.168.22.0/28. The administrator verifies the successful Telnet connections from a workstation with IP 192.168.22.5 to R1 before the ACL is applied. However, after the ACL is applied to the interface Fa0/0, Telnet connections are denied. What is the cause of the connection failure?

• • The enable secret password is not configured on R1.

  
  

• • The IT group network is included in the deny statement.

  
  

• • The permit ACE specifies a wrong port number.

  
  

• • The permit ACE should specify protocol ip instead of tcp.

  
  

• • The login command has not been entered for vty lines.

  
  

Match the type of WAN device or service to the description. (Not all options are used.)

• 1Пусто

  2CPE

  3Local loop

  4Пусто

  5DTE

  6DCE

• Запомните последовательность вставки

Refer to the exhibit. R1 is configured for NAT as displayed. What is wrong with the configuration?

• • NAT-POOL2 is not bound to ACL 1.

  
  

• • Interface Fa0/0 should be identified as an outside NAT interface.

  
  

• • The NAT pool is incorrect.

  
  

• • Access-list 1 is misconfigured.

  
  

Refer to the exhibit. What method can be used to enable an OSPF router to advertise a default route to neighboring OSPF routers?

• • Use a static route pointing to the ISP and redistribute it.

  
  

• • Use the redistribute static command on R0-A.

  
  

• • Use the default-information originate command on ISP.

  
  

• • Use the default-information originate command on R0-A.