NEW
Font size
S
M
L
XL
WorksheetsWoods I - Final Exam Review
Total questions: 22
Worksheet time: 11mins
Name
Class
Date
1.
Rounded to two decimal places, how many board feet is a board that measures ¾” x 20 1/2” x 25 ¼”?
a)
3.65
b)
a. 2.73
c)
2.70
d)
525
2.
With the wood species and cost per board foot given in the table, what is the cost for the Top?
a)
$6.91
b)
$6.90
c)
$2.18
d)
$2.17
3.
This defect is when there is bark or an absence of wood along an edge.
a)
wane
b)
split
c)
knots
d)
warp
4.
Which species of wood is a heavy, open grained, hardwood with its heartwood being a reddish brown color.
a)
White Ash
b)
White Oak
c)
Red Oak
d)
Eastern Red Cedar
5.
Which species of wood is a dense, heavy, hardwood, with its heartwood being chocolate brown and its sapwood being white? It is also an open grained wood that finishes nicely.
a)
Walnut
b)
Hard Maple
c)
Red Oak
d)
Cherry
6.
4/16 =
a)
3/4
b)
1/2
c)
1/4
d)
1/8
7.
10/16 =
a)
3/4
b)
5/8
c)
1/2
d)
3/8
8.
What is the easiest way to divide a fraction in half?
a)
Cut the denominator in half
b)
double the numerator
c)
Double the denominator
d)
Double the denominator and numerator
9.
What is half of 7/8?
a)
7/16
b)
3/8
c)
1/2
d)
5/16
10.
Which line is 3/16?
a)
B
b)
C
c)
D
d)
E
11.
Which is NOT a specific name for the pairs that make up the six sides to a board?
a)
side
b)
end
c)
surface/face
d)
edge
12.
Square cutting and crosscutting length makes which sides parallel?
a)
Ends
b)
Surfaces/faces
c)
Edges
d)
Sides
13.
Our stock comes surfaced on two sides, which means they come parallel to each other, thus allowing us to move the planing step to wherever it will be most efficient.
a)
True
b)
False
14.
What should you do to eliminate sharp corners on edges and ends?
a)
Cut with a dull blade on the miter saw
b)
Use 120 grit on a sanding block to ease the edges
c)
Use a 3/8” round over bit on all edges
d)
Use an orbital sander with 80 grit to round off edges
15.
Straight edges and ends should be sanded with which sander in order to remove blade marks and chipping/jointer chatter.
a)
Drum Sander
b)
Edge Sander
c)
Oscillating Spindle Sander
d)
Disc Sander
16.
The lower the grit, the smaller the particles, the smoother the finish.
a)
True
b)
False
17.
When using the orbital or random-orbit sander, always sand slowly (about 1 inch/sec) to help avoid pigtails and produce better results.
a)
True
b)
False
18.
What grit paper should be used to knock off the grain that raises to the surface between coats of finish?
a)
220
b)
120
c)
80
d)
180
19.
It’s okay to let any stain that doesn’t absorb into the wood grain to sit and dry on the surface.
a)
True
b)
False
20.
You should sand after your last coat of finish for a nice smooth surface.
a)
True
b)
False
21.
Necessary dry time between each coat of finish is:
a)
4 hrs
b)
24 hrs
c)
½ hr
d)
Whatever the container says
22.
What must be done before bringing your project into the finishing room?
a)
Keep door closed
b)
Turn on ventilation blower
c)
Put on gloves
d)
Remove all dust and particles from the project using a tack cloth or compressed air
Reset
