NEW
Font size
S
M
L
XL
WorksheetsCore: M10 Material Handling
Total questions: 18
Worksheet time: 9mins
Name
Class
Date
1.
Of the following, what should be done first when attempting to lift any material?
a)
look for any protruding nails, wires, or sharp edges
b)
use safety harnesses
c)
ask supervisor for assistance
d)
make sure the staking ratio is no more than 3 to 1
2.
before you attempt to lower an overhead load,
a)
size up the load
b)
put on a back support
c)
shrink wrap the load
d)
set up a fall zone
3.
Describe the proper procedure to lift an object.
a)
lift with your legs, keep your back straight, and keep your head up.
b)
bend over with your knees straight, feet together,and then lift.
c)
lift with your back, keep your legs straight and keep your arms up
d)
lift with your arms, keep your legs straight, and keep you head up.
4.
When stacking bags, step back and cross key the bags...
a)
every 10 bags high
b)
in each tier above seven feet
c)
until the stack reaches four feet
d)
all the way to the top of the pile
5.
Never stack or store materials...
a)
on scaffolds
b)
in cabinets
c)
outdoors
d)
on pallets
6.
Name this knot.
a)
clove hitch
b)
two half hitches
c)
bowline
d)
square knot
7.
a common way to tie a clove hitch is...
a)
use 2 half hitches
b)
use slip knots
c)
use a square knot
d)
use 2 bowlines
8.
when moving a material cart on an inclinded or declined surface, be sure...
a)
the load does not exceed the labeled weight capacity
b)
hand break is within your reach
c)
hydraulic ram has been removed
d)
load is cushioned with moving pads to prevent slippage
9.
in order to transport a bottle of compressed gas, use a
a)
cylinder cart
b)
hand truck
c)
wheelbarrow
d)
tunnel buggy
10.
What device may have a rotating table surface and/or spikes on the table surface for a better grip?
a)
roller skid
b)
pallet jack
c)
pallet conveyor
d)
accumulating conveyor
11.
in order to work with motorized material handling equipment, a worker must be...
a)
trained, certified, and authorized
b)
experienced and knowledgeable
c)
a job foreman or supervisor
d)
licensed to drive
12.
How would you define the fall zone for a forklift.
a)
any area into which the lifted materials could potentially fall
b)
minimum of 30' diameter corcle around the forklift
c)
twice the length of the base of the forklift
d)
twice the width of the object being lifted
13.
in order to prevent a tip over when driving a rough terrain forklift, keep the load...
a)
low
b)
high
c)
light
d)
heavy
14.
When using hand signals...
a)
maintain eye contact with the operator
b)
stand on something at least 2 feet high
c)
wear reflective gloves
d)
make sure you can hear the backup alarm
15.
the forklift hand signal for "dog everything" means...
a)
to pause
b)
creep forward
c)
tilt mast up
d)
deflate tires
16.
Name this Knot
a)
Bowline
b)
SlipKnot
c)
Clove Hitch
d)
Square Knot
17.
Name this Knot
a)
Square knot
b)
Bowline
c)
Half hitch
d)
quadknot
18.
Name this Knot
a)
Two half hitches
b)
Clove hitch
c)
Bowline
d)
Square knot
Reset
