WorksheetsSteering and Suspension ASE 2
Total questions: 30
Worksheet time: 35mins
Name
Class
Date
1.
Name this component
a)
Ball joint
b)
tie rod end
c)
control arm
d)
socket
2.
Name this component
a)
radius arm
b)
control arm
c)
strut
d)
steering rack
3.
Name this component
a)
u bolt
b)
leaf spring
c)
sway bar
4.
Name this component
a)
Strut
b)
shock
c)
coil spring
5.
Name this component
a)
control arm
b)
sway bar
c)
steering knuckle
6.
Which angle does not affect tire wear?
a)
caster
b)
camber
c)
toe
7.
Technician A says a vehicle will pull to the side with the most positive camber. Technician B says that too much negative camber will result in excessive wear on the inside tread of the tire. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
8.
Two technicians are discussing inner and outer tie rods. Technician A says to turn the outer tie rod end to adjust the toe. Technician B says loose inner tie rod ends will cause a tire to feather. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
9.
On cold mornings, the warning lamp on a vehicle with a TPMS tire pressure monitoring system stays illuminated for several minutes before it goes out. Which of these is MOST likely the cause of this condition.
a)
Clogged TPMS sensor.
b)
Worn tread on one of the tires.
c)
TPMS initialization.
d)
Low tire pressure.
10.
Two technicians are performing a power steering pressure test. Technician A says a restriction in the high pressure line results in higher than normal test results. Technician B says if the pressure increases when the shutoff valve is closed, there's a problem with the power steering pump. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
11.
A vehicle with a ribbed serpentine belt makes a chirping noise when starting. Technician A says to check the belt with a belt wear gauge. Technician B says proper belt deflection is 1/2 inch per foot of belt span. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
12.
Two technicians are discussing the toe setting of a front wheel drive vehicle with four wheel independent suspension. The right rear wheel is 1.5 degrees toe-in from specifications. Technician A says to set the front toe on this vehicle before correcting the rear. Technician B says the right rear wheels toe setting is 1.5 degrees positive (+). Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
13.
A vehicle with a power rack and pinion steering system is binding during turns. Which of the following is LEAST likely to cause this condition.
a)
Strut mount bearing.
b)
Worn rack bushings.
c)
Worn rack and pinion gear.
d)
Lower ball joint.
14.
After installing a power steering gear, the vehicle's air bag light is illuminated. Technician A says the vehicle's wheel alignment needs to be adjusted to repair this light. Technician B says the clockspring has been damaged. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
15.
A vehicle pulls to the right and makes a clunking sound when the brakes are applied. During an alignment check the technician notices excessive negative caster on the right front wheel. Technician A says this is most likely caused by a seized brake caliper. Technician B says this is most likely caused by worn or missing strut rod bushings. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
16.
During the visual inspection of a light truck, the technician notices the left rear leaf spring has a broken center bolt. Technician A says this will affect the vehicle's thrust angle. Technician B says an incorrect thrust angle will affect the centering of the steering wheel. Who is correct?
a)
Technician A only
b)
Technician B only
c)
Both Technician A and B
d)
Neither Technician A nor B
17.
What component is number 1?
a)
Rim
b)
Wheelbearing
c)
Spindle
d)
Axle
18.
What component is number 2?
a)
Rim
b)
Wheelbearing
c)
Knuckle
d)
Axle
19.
What component is number 3?
a)
Torsion Bar
b)
Steering Bracket
c)
Caliper
d)
Strut
20.
What component is number 4?
a)
Coil Spring
b)
Strut Cover
c)
Leaf Spring
d)
Axle dampener
21.
What component is number 5?
a)
Coil Spring
b)
Strut Dust Bellow or boot
c)
Tie rod
d)
Pitman Arm
22.
What component is number 6?
a)
Baffle
b)
Strut Cover
c)
Upper strut mount
d)
Nut
23.
What component is number 9?
a)
K member
b)
Torsion Bar
c)
Axle Support
d)
Lower Control Arm
24.
What component is number 10?
a)
Ball joint
b)
Lower control arm bushing
c)
Arm bearing
d)
Flex seal
25.
What component is number 11?
a)
Strut Brace
b)
Brake Rod
c)
Subframe
d)
Stabilizer Bar
26.
What component is number 13?
a)
Stabilizer bar bushing
b)
Axle nut
c)
Tie rod
d)
Pitman Arm
27.
Name this component
a)
lock nut
b)
castle nut
c)
acorn nut
28.
Name this component
a)
hitch pin
b)
cotter pin
c)
anchor pin
29.
Name this component
a)
sway bar
b)
bushing
c)
tie rod
30.
Name this component
a)
Tie rod end
b)
inner tie rod
c)
hammer
100 %
