NEW
Font size
S
M
L
XL
WorksheetsGeneral Automotive 1
Total questions: 25
Worksheet time: 16mins
Name
Class
Date
1.
A term used to identify the engine, transmission/transaxle, differential, axles, and wheels
a)
drive train
b)
drive shaft
c)
final drive
d)
flywheel
2.
Vehicle brakes are fitted to the wheels to provide a means of slowing down or stopping the vehicle and operate on the principle of________
a)
air pressure
b)
water pressure
c)
steam pressure
d)
hydraulic pressure
3.
What does ASE stand for?
a)
Automatic service engine
b)
Automotive service escape
c)
Automotive service excellence
d)
Automotive severe excellence
4.
a)
Ball pen hammer
b)
Super hammer
c)
Brass hammer
d)
sludge hammer
5.
If an engine is mounted Transverse (sideways) the vehicle will be "primarily" what drive type?
a)
RWD
b)
2WD
c)
4WD
d)
FWD
6.
Which of the following is NOT an engine configuration?
a)
HORIZONTAL
b)
INLINE
c)
V-
d)
VERTICAL
7.
Which of the following is NOT a stroke of a (four stroke) engine?
a)
Combustion
b)
Intake
c)
Exhaust
d)
power
8.
Tech A says that the automotive industry is highly technical and only a certain few people will find jobs. Tech B says the automotive industry is wide open with job opportunities for almost every level of skill. Who is correct? a. b. c. d.
a)
Tech A
b)
Tech B
c)
Both A and B
d)
Neither A nor B
9.
Tech A says that dealership technicians generally have access to manufacturers’ training to help prepare them as technicians. Tech B says that an independent shop works on a wide variety of equipment that requires a broad skill level in technicians. Who is correct? a. b. c. d.
a)
Tech A
b)
Tech B
c)
Both A and B
d)
Neither A nor B
10.
Which of the following drive types has a "transmission" rather than a "transaxle"?
a)
RWD
b)
FWD
c)
AWD
d)
Rear Mount
11.
The air conditioning compressor _____________ vaporized refrigerant and allows it to flow to the condenser.
a)
pressurizes
b)
cools
c)
supplies
d)
cleans
12.
Adding pressure to a liquid _______ its boiling point. Adding pressure to a vapor _______ its temperature.
a)
raises, raises
b)
lowers, lowers
c)
raises, lowers
d)
lowers, raises
13.
The Compressor discharge hose uses a _____________ diameter than the suction hose.
a)
larger
b)
smaller
c)
identical
d)
opposite
14.
What is the gear ratio in a simple gear train if the Driver has 17 teeth and the Driven has 53?
a)
0.32:1
b)
4.38:1
c)
3.11:1
d)
0.22:1
15.
When calculating gear ratios in a simple gear train, which is the correct formula?
a)
Driven divided by Driver
b)
Driver multiplied by Driven
c)
Driven multiplied by Driver
d)
Driver divided by Driven
16.
The component that acts as a switching device within a starter motor
a)
Commutator
b)
Armature
c)
Solenoid
d)
Pinion gear
17.
The gear ratio between the starter motor and the flywheel ring gear gives a reduction in…
a)
Speed
b)
Inertia
c)
Torque
d)
Charge
18.
During a starter current-draw test the following results were noted: Voltage—9.4 volts. Current draw—363 amps. The specifications for the maximum current draw are 180 amps.
a)
Technician A says the test results indicate that the battery may be defective and should be tested.
b)
Technician B says the test results indicate a faulty natural safety start switch circuit.
c)
Both are correct.
d)
Neither are correct
19.
Resistance in wire depends on how thick it is, how long it is and what it is made of.
a)
true
b)
false
20.
What is the resistance in this circuit?
a)
0.05Ω
b)
1.8Ω
c)
20Ω
21.
This is an example of a _______ circuit
a)
open
b)
series
c)
parallel
d)
square
22.
What is resistance measured in?
a)
Ω (Ohms)
b)
V (Volts)
c)
A (Amps)
d)
W (Watts)
23.
Which diagram shows two bulbs in a series?
a)
1
b)
2
c)
3
d)
4
24.
An electromagnet with a moving iron core that is used to cause mechanical motion.
a)
Solenoid
b)
Transistor
c)
Insulator
d)
Invertor
25.
A two-lead electronic component that allows current flow in one direction only.
a)
Ground
b)
Diode
c)
Switch
d)
Transistor
Reset
