WorksheetsPost-Mechatronics Safety Test
Total questions: 33
Worksheet time: 31mins
What type of fire extinguisher should be used on a grease or oil fire?
Class A
Class B
Class C
Class D
EPA regulations are designed to protect you from which of the following hazards?
Airborne and waterborne contaminants
Slips, trips, and falls
Fires
Mechanical hazards
The Clean Water Act is enforced by which agency?
OSHA
NIOSH
EPA
State Regulatory Agencies
Which agency certifies Personal Protective Equipment for workplace use?
OSHA
EPA
NIOSH
EPCRA
Standard operating procedures (SOP) are detailed documents that __________.
Provide a map of the plant or workplace
Explain each step in a work process
Provide several options to get the job done
Explain why safety is important
Which of the following is a common cause of workplace death?
Falls
Overexertion
Spilling chemicals on your body
Failure to wear Personal Protective Equipment
The process of identifying potential hazards in the workplace is known as a __________.
PPE analysis
injury analysis
hazard assessment
workplace inspection
Hard hats are NOT designed to protect you from electrical shock. Is this statement TRUE or FALSE?
True
False
Eye and face protection must protect you from the specific hazards that you may encounter in your workplace. Is this statement TRUE or FALSE?
True
False
What protection does a metatarsal guard provide?
Arm protection
Shin protection
Face protection
Foot protection
Synthetic material, such as rubberized fabric, is NOT an appropriate choice of PPE for an environment where fire is present. Is this statement TRUE or FALSE?
True
False
__________ are chemicals that fuel the combustion of other materials.
Flammables
Accelerants
Oxidizers
Explosives
Safe handling procedures of chemicals are found in the __________ document.
DOT
GHS
SDS
HMZ
__________ is a system that rotates chemical stock to ensure they are used within their shelf life.
Just in time
First in, first out
Supply and demand
Stock rollover
The __________ provides guidelines for disposal of chemicals without dumping or discarding.
DOJ
EMT
NRA
EPA
When you are securing your load, that action is called?
Rigging
Fingerling
Gigging
Trapping
A sensor that stops a machine if a door is opened is an example of a(n) __________.
Barrier interlock
Guard interlock
Electrical interlock
mechanical interlock
when carrying a load on a forklift where you CANNOT see forward, you should
Drive in reverse while looking over your shoulder
Drive slowly and carefully
drive forward and use the horn often
drive forward and turn on your lights
The industrial truck that lifts the operator up to pick parts from high shelves is called a?
picker truck or narrow aisle picker
Sit down forklift
Stand up forklift
Walkie pallet low lift
A Type A fire consists of
wood and paper, anything that leaves an ash when burned
Oils and gasoline
Electrical equipment
exotic metals
what type of extinguisher is used for special electronics
Halon
Water
Carbon Dioxide (CO2)
pressurized water
a class C fire is
From Electrical equipment
from Paper and wood
from Oil and Gas
From exotic metals like Lithium
A(n) __________ prevents a machine from operating without the proper guards in place.
Deadman switch
hard stop
interlock
Lockout
When using the fire extinguisher use the PASS method which means?
pull, aim, squeeze, sweep
push, arrive, survey, sound the alarm
pull, announce, settle down, seal
pick extinguisher, arrive at fire, see the fire, shout "FIRE!"
If an operator knows a safety problem exists with a machine, the operator should __________.
Try to correct the problem
Use caution while operating the machine
Operate the machine normally
Notify a supervisor immediately
when you hear the fire alarm
turn off your equipment, exit quickly and safely
if you are first to the exit door, you should hold it open for others
Look around to see if others are leaving
Wait for your supervisor to tell you what to do
If you are the only person at the scene of an injured coworker, first you should
Call 911 or tell another person to call 911
move the injured person if they are on the ground
check for a pulse
Ask questions so you know what happened
If you see someone injured by electrical shock and they are still touching live electrical wires, you should
attempt to knock the person away from the electrical source using a wooden board or other non-conductive object
Grab them with your finger tips to avoid a full shock of electrical energy
splash water on them
push them away with your non-conductive shoe
where eye wash stations are needed, they should be no farther away than
25 to 50 feet
5 feet
less than 100 feet but more than 10 feet
in reach from your work station
A machine __________ is a device that is designed to keep the operator clear of dangerous machine parts.
Barrier
guard
Rest
emergency stop
A(n) __________ prevents someone from powering up a machine while it is being serviced by someone else.
emergency stop
cycle halt
Lockout
interlock
The __________ warns others not to restore power to a machine.
cycle halt
Tagout
Lockout
interlock
Who is authorized to remove a lockout/tagout from a machine?
The person who installed it
The lead technician on the service team
The foreman supervision the machine service
The plant manager
