WorksheetsSafety Quiz
Total questions: 20
Worksheet time: 10mins
Name
Class
Date
1.
a)
planer
b)
thicknesser
c)
circular saw
d)
sawbench
2.
a)
bandsaw
b)
drillpress
c)
drill
d)
saw
3.
a)
workbench
b)
jointer surfacer
c)
planer
d)
saw
4.
a)
cordless drill
b)
bandsaw
c)
drillpress
d)
workbench
5.
a)
planer
b)
mortise machine
c)
sawbench
d)
lathe
6.
Which of the following is the most effective method of keeping the workshop dust free?
a)
· Regular sweeping up
b)
· Putting water down before cleaning up
c)
· Doing dusty jobs outside
d)
· Using a suitable vacuum cleaner
7.
When, if at all, is it acceptable to operate a circular saw for a sawing operation without a guard?
a)
· When the saw is required for rebating
b)
· When the saw is required for deep cutting
c)
· When the timber is particularly badly bowed
d)
· It is not acceptable under any circumstances
8.
What is the function of a jointer?
a)
to make a rip cut on a board
b)
a woodworking machine used to produce a flat surface along a board's length and edge.
c)
to make a crosscut on a board
d)
All of the above
9.
What surface should you machine first on a board?
a)
Face
b)
Edge.
c)
End
d)
None of the above
10.
Identify the red part displayed in the photo??
a)
Guard for the belt sander
b)
Guard for the cutter head
c)
Guard for the miter saw
d)
Guard for the table saw
11.
Identify this part on this woodworking equipment.
a)
Infeed table
b)
Guard
c)
Fence
d)
Outfeed table
12.
You should avoid jointing an _______ on a board
a)
Face
b)
Edge
c)
End
d)
None of the above
13.
Check all wood for knots, splits, nails or metal and other imperfections
a)
Knots
b)
Splits
c)
Nails
d)
All of the above
14.
Stock to be planed of a jointer should be at least _____ inches long.
a)
12"
b)
9"
c)
16"
d)
18"
15.
What is the final step to squaring a board?
a)
Cut to length (always last) using miter saw
b)
Check for squareness
c)
Cut to length (always last) using radial arm saw
d)
Joint the other edge
16.
What is the maximum cut for surfacing stock?
a)
1/32”
b)
1/8”
c)
1/4"
d)
1/16”
17.
How far away must your hand or fingers be in order to not use a push block on the table saw?
a)
3 inches
b)
4 inches
c)
1 foot
d)
You do not need to use a push block.
18.
When may the operator leave a machine?
a)
When the operator pushes the off button.
b)
Whenever the operator wants to.
c)
When the blade has stopped.
d)
When Mr. Donmoyer says clean up.
19.
What should you do before you start the Jointer.
a)
Make sure the infeed table is 1/16" below the outfeed table.
b)
Test the blade guard to make sure it goes back to its starting position.
c)
Make sure the fence is perpendicular to the table.
d)
All of the above.
20.
How far above should the Table Saw blade be above your work?
a)
1/2"
b)
1"
c)
3/4"
d)
1/4"
100 %
