NEW
Font size
WorksheetsRevision V
Total questions: 20
Worksheet time: 3mins
The belt of an electric motor frayed. Which maintenance is appropriate?
Predictive maintenance. / Penyelenggaraan ramalan.
Corrective maintenance. / Penyelenggaraan pembetulan.
Scheduled maintenance. / Penyelenggaraan berjadual.
Preventive maintenance. / Penyelenggaraan pencegahan.
What is the function of the toolbar in Figure 9?
To zoom certain area. / Untuk zum kawasan tertentu.
To view isometric angle. / Untuk melihat sudut isometrik.
To adjust the dimension. / Untuk menyesuaikan dimensi.
To look at certain area of object. / Untuk melihat bahagian objek tertentu.
What is the function of SNAP in AutoCAD?
To design orthogonal drawing or rectangular drawing.
A step that will move the cursor on a specific drawing.
Aiming (target) at a particular point of a line derived from activated.
To set up and draw it with absolute or relative coordinates with drawing lines.
Which of the following, is NOT an advantages of AutoCAD?
Save money for drawing.
Improving quality of end product.
Faster editing, reviewing and designing.
Improving productivity, capability and accuracy.
Which is NOT refer to scheduled maintenance?
Examine machine.
Cleaning of water tank.
Whitewashing of building.
Repairing break down machine.
What is the main objective of carrying out Total Productive Maintenance?
Less idle time. / Kurang masa terbiar.
Zero downtime. / Tiada “downtime”.
Increase in productivity. / Meningkatkan produktiviti.
Maximize production cost. / Memaksimumkan kos pengeluaran.
What is the definition of on the job training (OJT)?
Trainings based on self study
Training conducted by consultants.
Training conducted at the place of work.
Training done at a location away from work place.
What is the function of the input interface module?
To connect data to CPU.
To connect input to output.
To enable input to be connected to PLC.
To enable input to be connected to memory.
Which of the following, statement is TRUE for Ladder Logic?
Coil is on the right.
Rungs are not numbered.
Same input cannot be used on other rungs.
Same coil contact can be used on other rungs.
Arrange the following steps for motor wiring from PLC.
I. Motor. / Motor.
II. Relay Coil. / Coil Relay.
III. PLC Output. / Output PLC.
IV. Relay Contact. / Contact Relay.
II, III, IV, I
II, III, I, IV
III, II, IV, I
III, IV, II, I
What is the total capacitance of circuit in Figure 1?
15pF
30pF
105 pF
160 pF
Which of the following is the best way to achieve good soldering joint?
Apply a lot of flux when soldering.
Apply the iron tip firmly until the solder wets.
Smoothen the solder by stroking with the iron tip.
Heat more than 10 seconds before applying the solder.
Which below is NOT types of CAD software?
Catia.
AutoCAD.
SolidWork.
CAD Design.
1. What is the function of the toolbar in Figure 2?
To extend the length of an object.
To increase the radius of an object.
To determine the shape of the object.
To determine the dimension of any object.
What is the process by means of which an instrument is aligned such that measuring deviation from the set point value is minimal, and within the allowable tolerances specified for the instrument?
Tuning. / Penalaan.
Correction. / Pembetulan.
Calibration. Penentukuran.
Adjustment. / Pelarasan.
What is the name of component shown in Diagram 7?
Diode. / Diod.
Capacitor. / Kapasitor.
Transistor. / Transistor.
Light Emitting Diode (LED). / Diod Pemancar Cahaya (LED).
Which is associated with what is termed a “limited calibration”?
Guaranteed calibration service.
Limited liability calibration service.
Warranty-covered calibration service.
Limited functional testing of instrument.
There are 8 pillars in TPM. What is meant by TPM?
Total Productive Maintenance. / Total Productive Maintenance.
Total Preventive Maintenance. / Total Preventive Maintenance.
Timeline Productive Maintenance. / Timeline Productive Maintenance.
Timeline Preventive Maintenance. / Timeline Preventive Maintenance.
What is NOT the primary purpose of monitoring and calibrating test equipment on a regular basis?
A. To maintain instrument accuracy.
A. To ensure equipment cost not downgraded.
A. To ensure measurement traceability to national standards.
To comply with ISO 9000-9004 series of standards requirements
What does number on the Figure 8 mean?
Total inputs. / Jumlah input.
Total outputs. / Jumlah output.
Total current. / Jumlah arus.
Total inputs and outputs. / Jumlah input dan output.
