Free Printable General applications and terms

Worksheets

General applications and terms

Total questions: 25

Worksheet time: 17mins

Name

Class

Date

For a component that will be subjected to vibration, how would be best to fix it in place?

Bolt and spring washer behind a nut

Nut and bolt with a plain washer

Bolt with tread lock

Where would you use a split pin?

as a temporary fastener on components that need to be separated,

as a permanent method to fix components in place.

as a method of ensuring material stability

Which tool would be best for hitting a chisel with for joinery?

Lump hammer

Pin hammer

Mallet

Claw hammer

Which units do we use to measure and mark out in the UK?

Metric

Imperial

10CM is the equivalent to...

1000mm

10mm

100mm

1mm

which chisel is a general all rounder?

firmer chisel

bevel edge chisel

mortice chisel

Paring chiesel

hand planes are generally for.....

cutting wood

shaping wood

assembling products

making a surface un-even

This plane is mainly used for squaring raw lumber

Block Plane

Bench Plane

Smoothing PLane

Jack Plane

Good for flattening and smoothing the face of a board.

Smooth

Jack

Block

Rabbet

10.

Ideal for trimming small areas

Block

Smooth

Smaller

Jack

11.

A block plane can be used to:

Flatten long surfaces

Prepare rough cut lumber

Square a rough board

"Fine tune" miter cuts

12.

The angle on the edge of the plane blade is ___________degrees.

30-35

25-30

13.

True or False- when planing end grain, one should start in the middle and plane towards the edge.

true

false

14.

What is the purpose of the metal ferrule around the top of a mortice chisel?

To aid stability when the handle is struck

To prevent the handle from ‘mushrooming’

To provide a nice finish to the handle

To prevent damage when the chisel is left in the tool box

15.

What is the best way of carrying chisels when they are not in use?

Taped together with duck tape

Thrown in a box

Wrapped in building paper

Stored in a chisel roll

16.

Which of the following best describes the correct method of using a handsaw?

Use short cutting strokes so that all the teeth of the saw are being used

Use long cutting strokes so that some of the teeth of the saw are being used

Use short cutting strokes so that some of the teeth of the saw are being used

Use long cutting strokes so that all the teeth of the saw are being used

17.

Which of the following best describes a ‘Rip saw’?

Mostly used for general-purpose crosscutting to length.

It is the largest handsaw, They are used for cutting along the grain only

It is the smallest of the handsaws .Used for cutting up sheet material.

It has teeth that retain their edge longer

18.

Why do accident Books need to be kept in any workplace ?

By law under HASAWA 1974 ?

Only if the company wants to ?

19.

Under HASAWA which of the following is the employee's responsibility?

To take reasonable care for their own health and safety.

Write their own risk assessments

Provide their own PPE.

To replace damaged PPE.

Page

20.

To mark out angles greater than 90 degrees, what marking tool would be used?

Marking gauge

Set square

Sliding bevel

Combination Square

21.

Which of the following ensures efficient production and profitability of a project?

There is a good setter out

All tasks are completed at the given time frame

The marker out is faster than other marker out people employer by the company

No one has any time off through sickness

22.

What type of glue is PVA?

Polyvinyl acetate

Polyvinylidene fluoride

Polyvinylcarbazole

Polyvbest

23.

The ______________ of a ship is a wheel used for steering.

helm

wharf

keel

24.

The kitchen on a boat is called the ________.

galley

deck

marina

25.

This powers the boat forward or backwards.

Hull

Propeller

Impeller

Rudder

Reset

General applications and terms

Total questions: 25

Worksheet time: 17mins

Similar Resources on Wayground