Font size
WorksheetsPOST_TEST CCNP
Total questions: 20
Worksheet time: 10mins
What is a characteristic of a floating static route?
When it is configured, it creates a gateway of last resort.
OpIt is simply a static route with 0.0.0.0/0 as the destination IPv4 address.tion 2
It is used to provide load balancing between static routes.
It is configured with a higher administrative distance than the original dynamic routing protocol has.
Which route would be used to forward a packet with a source IP address of 192.168.10.1 and a destination IP address of 10.1.1.1?
C 192.168.10.0/30 is directly connected, GigabitEthernet0/1
O 10.1.1.0/24 [110/65] via 192.168.200.2, 00:01:20, Serial0/1/0
S* 0.0.0.0/0 [1/0] via 172.16.1.1
S 10.1.0.0/16 is directly connected, GigabitEthernet0/0
Which reason could cause an OSPF neighborship to be in the EXSTART/EXCHANGEstate?
mismatched OSPF link costs
mismatched MTU size
mismatched areas
mismatched OSPF network type
In OSPF, which LSA type is responsible for pointing to the ASBR router?
type 1
type 2
type 3
type 4
Which OSPF network types are compatible and allow communication through the twopeering devices?
point-to-multipoint to broadcast
broadcast to point-to-point
broadcast to nonbroadcast
point-to-multipoint to nonbroadcast
What is the difference between a RIB and a FIB?
The FIB is where all IP routing information is stored
The RIB maintains a mirror image of the FIB.
The RIB is used to make IP source prefix-based switching decisions
The FIB is populated based on RIB content
What is the correct sequence of attributes in BGP
Weight, Local Preference, Originate, AS Path, Origin code, MED, Paths, Router ID
Weight, Local Preference, Originate, AS Path, Router ID , Origin code, MED, Paths
Weight, Router ID , Local Preference, Originate, AS Path, Origin code, MED, Paths
Weight, Originate, AS Path, Origin code, MED, Paths, Router ID, Local Preference
Which of the following are VLAN Trunking protocols?
IEEE 802.1Q
Cisco ISL
VTP
STP
Which of the below are OSPF special Area Types?
Stub Area
Totally Stub Area
Totally Not So Stubby Area (Totally NSSA)
When a switch running RSTP receives an 802.1D BPDU, what happens?
The switch disables RSTP.
The switch begins to use 802.1D rules on that port.
An ICMP message is returned.
The BPDU is discarded or dropped.
Which DTP switch port mode allows the port to create a trunk link if the neighboring port is in trunk mode, or desirable auto mode?
Dynamic auto
Access
Dynamic desirable
Trunk
Which of the following is a valid EtherChannel negotiation mode combination between two switches?
PAgP auto, PAgP auto
on, PAgP auto
PAgP auto, PAgP desirable
LACP passive, LACP passive
Which one of the following commands enables the use of RSTP?
spanning-tree mode rapid-pvst
no spanning-tree mode pvst
spanning-tree rstp
spanning-tree mode rstp
None. RSTP is enabled by default.
How can the EtherChannel load-balancing method be set?
Per EtherChannel
Per switch port
Globally per switch
Can’t be configured
Which of the following is not a port state in RSTP?
Listening
Discarding
Learning
Forwarding
Which one of the following VTP modes does not allow any manual VLAN configuration changes?
Server
Client
Designated
Transparent
Where should the root bridge be placed on a network?
Closest to the most users
On the fastest switch
Closest to the center of the network
On the least-used switch
Which of these parameters should you change to make a switch become a root bridge?
Port priority
Bridge priority
Path cost
Switch MAC address
What is the purpose of VTP pruning?
Limit the size of the virtual tree
Limit the extent of broadcast traffic
Limit the number of VLANs in a domain
Stop unnecessary VTP advertisements
Where should the STP UplinkFast feature be enabled?
A distribution-layer switch.
An access-layer switch.
A core-layer switch.
All these answers are correct.
